[PATCH 1/2] arm64: dts: qcom: sm7225-fairphone-fp4: Configure PM8008 regulators

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



PM8008 regulators are used for the cameras found on FP4. Configure the
chip and its voltages.

Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts | 109 +++++++++++++++++++++-
 1 file changed, 108 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
index 6d7ab931e56b..a74f3ac09a5e 100644
--- a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
+++ b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
@@ -117,6 +117,25 @@ active-config0 {
 				};
 			};
 		};
+
+		pm8008-thermal {
+			polling-delay-passive = <100>;
+			thermal-sensors = <&pm8008>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
 	};
 };
 
@@ -404,7 +423,79 @@ &i2c8 {
 };
 
 &i2c10 {
-	/* PM8008 PMIC @ 8 and 9 */
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pm8008: pmic@8 {
+		compatible = "qcom,pm8008";
+		reg = <0x8>;
+
+		interrupts-extended = <&tlmm 59 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+
+		vdd-l1-l2-supply = <&vreg_s8e>;
+		vdd-l3-l4-supply = <&vreg_bob>;
+		vdd-l5-supply = <&vreg_bob>;
+		vdd-l6-supply = <&vreg_s2a>;
+		vdd-l7-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm8008_default>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&pm8008 0 0 2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		#thermal-sensor-cells = <0>;
+
+		regulators {
+			vreg_l1p: ldo1 {
+				regulator-name = "vreg_l1p";
+				regulator-min-microvolt = <528000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l2p: ldo2 {
+				regulator-name = "vreg_l2p";
+				regulator-min-microvolt = <528000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l3p: ldo3 {
+				regulator-name = "vreg_l3p";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vreg_l4p: ldo4 {
+				regulator-name = "vreg_l4p";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2904000>;
+			};
+
+			vreg_l5p: ldo5 {
+				regulator-name = "vreg_l5p";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2900000>;
+			};
+
+			vreg_l6p: ldo6 {
+				regulator-name = "vreg_l6p";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vreg_l7p: ldo7 {
+				regulator-name = "vreg_l7p";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <3140000>;
+			};
+		};
+	};
+
 	/* PX8618 @ 26 */
 	/* SMB1395 PMIC @ 34 */
 	/* awinic,aw8695 @ 5a */
@@ -717,6 +808,22 @@ qup_uart1_sleep_tx: qup-uart1-sleep-tx-state {
 		 */
 		bias-pull-up;
 	};
+
+	pm8008_default: pm8008-default-state {
+		int-pins {
+			pins = "gpio59";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		reset-n-pins {
+			pins = "gpio58";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
 };
 
 &uart1 {

-- 
2.45.2





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux