From: Tomi Valkeinen <tomi.valkeinen@xxxxxx> J721E common processor board can be interfaced with the infotainment expansion board[0] to enable the following audio/video interfaces in addition to the peripherals provided by the common processor board: - Two Audio codecs each with three Stereo Inputs and four Stereo Outputs - Audio input over FPD Link III - Digital Audio Interface TX/RX - HDMI/FPD LINK III Display out - LI/OV Camera input Add support for TFP410 HDMI bridge located on the Infotainment Expansion Board (connected to J46 & J51). Add a HDMI connector node and connect the endpoints as below: DSS => TFP410 bridge => HDMI connector Also add the pinmux data and board muxes for DPI. Rest of the peripherals are not added as of now. [0]: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx> [j-choudhary@xxxxxx: minor cleanup] Signed-off-by: Jayesh Choudhary <j-choudhary@xxxxxx> --- Testlog: <https://gist.github.com/Jayesh2000/45f75cf075cc969d1dfc9015c6f23fd4> Changelog v1->v2: - rebased on next-20240613 - add dtbo in ascending order in Makefile - Mention in commit message that other peripherals on the expansion board are not added as of now. v1 patch: <https://lore.kernel.org/all/20240227120310.661579-1-j-choudhary@xxxxxx/> arch/arm64/boot/dts/ti/Makefile | 4 + ...-j721e-common-proc-board-infotainment.dtso | 164 ++++++++++++++++++ 2 files changed, 168 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index d956372a7163..5c6701897f31 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -83,6 +83,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb # Boards with J721e SoC k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb +dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board-infotainment.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-pcie0-ep.dtbo @@ -151,6 +152,8 @@ k3-am68-sk-base-board-csi2-dual-imx219-dtbs := k3-am68-sk-base-board.dtb \ k3-j721e-sk-csi2-dual-imx219.dtbo k3-am69-sk-csi2-dual-imx219-dtbs := k3-am69-sk.dtb \ k3-j721e-sk-csi2-dual-imx219.dtbo +k3-j721e-common-proc-board-infotainment-dtbs := k3-j721e-common-proc-board.dtb \ + k3-j721e-common-proc-board-infotainment.dtbo k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-common-proc-board.dtb \ k3-j721e-evm-pcie0-ep.dtbo k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \ @@ -182,6 +185,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \ k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \ k3-am68-sk-base-board-csi2-dual-imx219.dtb \ k3-am69-sk-csi2-dual-imx219.dtb \ + k3-j721e-common-proc-board-infotainment.dtb \ k3-j721e-evm-pcie0-ep.dtb \ k3-j721e-sk-csi2-dual-imx219.dtb \ k3-j721s2-evm-pcie1-ep.dtb \ diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso new file mode 100644 index 000000000000..65a7e54f0884 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0-only OR MIT +/* + * Infotainment Expansion Board for j721e-evm + * User Guide: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf> + * + * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#include "k3-pinctrl.h" + +&{/} { + hdmi-connector { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + ddc-i2c-bus = <&main_i2c1>; + digital; + /* P12 - HDMI_HPD */ + hpd-gpios = <&exp6 10 GPIO_ACTIVE_HIGH>; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; + + dvi-bridge { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tfp410"; + /* P10 - HDMI_PDn */ + powerdown-gpios = <&exp6 8 GPIO_ACTIVE_LOW>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint { + remote-endpoint = <&dpi_out0>; + pclk-sample = <1>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint { + remote-endpoint = + <&hdmi_connector_in>; + }; + }; + }; +}; + +&main_pmx0 { + main_i2c1_exp6_pins_default: main-i2c1-exp6-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x264, PIN_INPUT, 7) /* (T29) MMC2_DAT2.GPIO1_24 */ + >; + }; + + dss_vout0_pins_default: dss-vout0-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x58, PIN_OUTPUT, 10) /* (AE22) PRG1_PRU1_GPO0.VOUT0_DATA0 */ + J721E_IOPAD(0x5c, PIN_OUTPUT, 10) /* (AG23) PRG1_PRU1_GPO1.VOUT0_DATA1 */ + J721E_IOPAD(0x60, PIN_OUTPUT, 10) /* (AF23) PRG1_PRU1_GPO2.VOUT0_DATA2 */ + J721E_IOPAD(0x64, PIN_OUTPUT, 10) /* (AD23) PRG1_PRU1_GPO3.VOUT0_DATA3 */ + J721E_IOPAD(0x68, PIN_OUTPUT, 10) /* (AH24) PRG1_PRU1_GPO4.VOUT0_DATA4 */ + J721E_IOPAD(0x6c, PIN_OUTPUT, 10) /* (AG21) PRG1_PRU1_GPO5.VOUT0_DATA5 */ + J721E_IOPAD(0x70, PIN_OUTPUT, 10) /* (AE23) PRG1_PRU1_GPO6.VOUT0_DATA6 */ + J721E_IOPAD(0x74, PIN_OUTPUT, 10) /* (AC21) PRG1_PRU1_GPO7.VOUT0_DATA7 */ + J721E_IOPAD(0x78, PIN_OUTPUT, 10) /* (Y23) PRG1_PRU1_GPO8.VOUT0_DATA8 */ + J721E_IOPAD(0x7c, PIN_OUTPUT, 10) /* (AF21) PRG1_PRU1_GPO9.VOUT0_DATA9 */ + J721E_IOPAD(0x80, PIN_OUTPUT, 10) /* (AB23) PRG1_PRU1_GPO10.VOUT0_DATA10 */ + J721E_IOPAD(0x84, PIN_OUTPUT, 10) /* (AJ25) PRG1_PRU1_GPO11.VOUT0_DATA11 */ + J721E_IOPAD(0x88, PIN_OUTPUT, 10) /* (AH25) PRG1_PRU1_GPO12.VOUT0_DATA12 */ + J721E_IOPAD(0x8c, PIN_OUTPUT, 10) /* (AG25) PRG1_PRU1_GPO13.VOUT0_DATA13 */ + J721E_IOPAD(0x90, PIN_OUTPUT, 10) /* (AH26) PRG1_PRU1_GPO14.VOUT0_DATA14 */ + J721E_IOPAD(0x94, PIN_OUTPUT, 10) /* (AJ27) PRG1_PRU1_GPO15.VOUT0_DATA15 */ + J721E_IOPAD(0x30, PIN_OUTPUT, 10) /* (AF24) PRG1_PRU0_GPO11.VOUT0_DATA16 */ + J721E_IOPAD(0x34, PIN_OUTPUT, 10) /* (AJ24) PRG1_PRU0_GPO12.VOUT0_DATA17 */ + J721E_IOPAD(0x38, PIN_OUTPUT, 10) /* (AG24) PRG1_PRU0_GPO13.VOUT0_DATA18 */ + J721E_IOPAD(0x3c, PIN_OUTPUT, 10) /* (AD24) PRG1_PRU0_GPO14.VOUT0_DATA19 */ + J721E_IOPAD(0x40, PIN_OUTPUT, 10) /* (AC24) PRG1_PRU0_GPO15.VOUT0_DATA20 */ + J721E_IOPAD(0x44, PIN_OUTPUT, 10) /* (AE24) PRG1_PRU0_GPO16.VOUT0_DATA21 */ + J721E_IOPAD(0x24, PIN_OUTPUT, 10) /* (AJ20) PRG1_PRU0_GPO8.VOUT0_DATA22 */ + J721E_IOPAD(0x28, PIN_OUTPUT, 10) /* (AG20) PRG1_PRU0_GPO9.VOUT0_DATA23 */ + J721E_IOPAD(0x9c, PIN_OUTPUT, 10) /* (AC22) PRG1_PRU1_GPO17.VOUT0_DE */ + J721E_IOPAD(0x98, PIN_OUTPUT, 10) /* (AJ26) PRG1_PRU1_GPO16.VOUT0_HSYNC */ + J721E_IOPAD(0xa4, PIN_OUTPUT, 10) /* (AH22) PRG1_PRU1_GPO19.VOUT0_PCLK */ + J721E_IOPAD(0xa0, PIN_OUTPUT, 10) /* (AJ22) PRG1_PRU1_GPO18.VOUT0_VSYNC */ + >; + }; +}; + +&exp1 { + p14-hog { + /* P14 - VINOUT_MUX_SEL0 */ + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "VINOUT_MUX_SEL0"; + }; + + p15-hog { + /* P15 - VINOUT_MUX_SEL1 */ + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "VINOUT_MUX_SEL1"; + }; +}; + +&main_i2c1 { + /* i2c1 is used for DVI DDC, so we need to use 100kHz */ + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + + exp6: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_exp6_pins_default>; + interrupt-parent = <&main_gpio1>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + p11-hog { + /* P11 - HDMI_DDC_OE */ + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "HDMI_DDC_OE"; + }; + }; +}; + +&dss { + pinctrl-names = "default"; + pinctrl-0 = <&dss_vout0_pins_default>; +}; + +&dss_ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + dpi_out0: endpoint { + remote-endpoint = <&tfp410_in>; + }; + }; +}; -- 2.25.1
