On Thu, Jun 6, 2024 at 5:52 PM Andre Przywara <andre.przywara@xxxxxxx> wrote:
>
> On Wed, 5 Jun 2024 13:53:39 -0500
> Chris Morgan <macroalpha82@xxxxxxxxx> wrote:
>
> > From: Chris Morgan <macromorgan@xxxxxxxxxxx>
> >
> > The Anbernic RG35XXSP is almost identical to the RG35XX-Plus, but in a
> > clamshell form-factor. The key differences between the SP and the Plus
> > is a lid switch and an RTC on the same i2c bus as the PMIC.
> >
> > Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/allwinner/Makefile | 3 +-
> > .../sun50i-h700-anbernic-rg35xx-sp.dts | 145 ++++++++++++++++++
> > 2 files changed, 147 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-sp.dts
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> > index 0db7b60b49a1..00bed412ee31 100644
> > --- a/arch/arm64/boot/dts/allwinner/Makefile
> > +++ b/arch/arm64/boot/dts/allwinner/Makefile
> > @@ -49,5 +49,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb
> > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
> > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
> > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb
> > -dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-plus.dtb
> > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-h.dtb
> > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-plus.dtb
> > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-sp.dtb
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-sp.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-sp.dts
> > new file mode 100644
> > index 000000000000..a1d16b65ef5d
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-sp.dts
> > @@ -0,0 +1,145 @@
> > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +/*
> > + * Copyright (C) 2024 Ryan Walklin <ryan@xxxxxxxxxxxxx>.
> > + * Copyright (C) 2024 Chris Morgan <macroalpha82@xxxxxxxxx>.
> > + */
> > +
> > +#include <dt-bindings/input/gpio-keys.h>
> > +#include "sun50i-h700-anbernic-rg35xx-plus.dts"
> > +
> > +/ {
> > + model = "Anbernic RG35XX SP";
> > + compatible = "anbernic,rg35xx-sp", "allwinner,sun50i-h700";
> > +
> > + gpio-keys-lid {
> > + compatible = "gpio-keys";
> > +
> > + lid-switch {
> > + label = "Lid Switch";
> > + gpios = <&pio 4 7 GPIO_ACTIVE_LOW>; /* PE7 */
> > + linux,can-disable;
> > + linux,code = <SW_LID>;
> > + linux,input-type = <EV_SW>;
> > + wakeup-event-action = <EV_ACT_DEASSERTED>;
> > + wakeup-source;
> > + };
> > + };
> > +};
> > +
> > +/delete-node/ &r_rsb;
>
> I don't think deleting the *RSB* node is right here, if at all, I'd expect
> status="disabled", and then maybe deleting the axp717 node within?
> Or maybe factor the AXP node out into a separate file, and include it from
> the -2024.dts and from this one?
Doesn't quite work because the unit address is different.
> Or move every board to I2C?
Doesn't this depend on the bootloader also running in RSB mode? My memory
is a bit foggy on this, but IIRC we did a conversion on some other boards
before?
> What do people think about this?
"disabled" in RSB node and deleting the axp717 node is probably the right
thing to do.
> Cheers,
> Andre
>
> > +
> > +&r_i2c {
> > + pinctrl-0 = <&r_i2c_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +
> > + axp717: pmic@34 {
> > + compatible = "x-powers,axp717";
> > + reg = <0x34>;
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + interrupt-parent = <&nmi_intc>;
> > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > +
> > + vin1-supply = <®_vcc5v>;
> > + vin2-supply = <®_vcc5v>;
> > + vin3-supply = <®_vcc5v>;
> > + vin4-supply = <®_vcc5v>;
> > +
> > + regulators {
> > + reg_dcdc1: dcdc1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <900000>;
> > + regulator-max-microvolt = <1100000>;
> > + regulator-name = "vdd-cpu";
> > + };
> > +
> > + reg_dcdc2: dcdc2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <940000>;
> > + regulator-max-microvolt = <940000>;
> > + regulator-name = "vdd-gpu-sys";
> > + };
> > +
> > + reg_dcdc3: dcdc3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1100000>;
> > + regulator-name = "vdd-dram";
> > + };
> > +
> > + reg_aldo1: aldo1 {
> > + /* 1.8v - unused */
> > + };
You can drop all the unused ones, unless you plan to include *this*
file from another one and use those nodes/labels.
ChenYu
> > +
> > + reg_aldo2: aldo2 {
> > + /* 1.8v - unused */
> > + };
> > +
> > + reg_aldo3: aldo3 {
> > + /* 1.8v - unused */
> > + };
> > +
> > + reg_aldo4: aldo4 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-pg";
> > + };
> > +
> > + reg_bldo1: bldo1 {
> > + /* 1.8v - unused */
> > + };
> > +
> > + reg_bldo2: bldo2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-pll";
> > + };
> > +
> > + reg_bldo3: bldo3 {
> > + /* 2.8v - unused */
> > + };
> > +
> > + reg_bldo4: bldo4 {
> > + /* 1.2v - unused */
> > + };
> > +
> > + reg_cldo1: cldo1 {
> > + /* 3.3v - audio codec - not yet implemented */
> > + };
> > +
> > + reg_cldo2: cldo2 {
> > + /* 3.3v - unused */
> > + };
> > +
> > + reg_cldo3: cldo3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-io";
> > + };
> > +
> > + reg_cldo4: cldo4 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi";
> > + };
> > +
> > + reg_boost: boost {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5200000>;
> > + regulator-name = "boost";
> > + };
> > +
> > + reg_cpusldo: cpusldo {
> > + /* unused */
> > + };
> > + };
> > + };
> > +
> > + rtc_ext: rtc@51 {
> > + compatible = "nxp,pcf8563";
> > + reg = <0x51>;
> > + };
> > +};
>
>
