[PATCH v16 4/5] clk: sophgo: Add SG2042 clock driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Chen Wang <unicorn_wang@xxxxxxxxxxx>

Add a driver for the SOPHGO SG2042 clocks.

Signed-off-by: Chen Wang <unicorn_wang@xxxxxxxxxxx>
---
 drivers/clk/sophgo/Kconfig             |   28 +
 drivers/clk/sophgo/Makefile            |    4 +
 drivers/clk/sophgo/clk-sg2042-clkgen.c | 1152 ++++++++++++++++++++++++
 drivers/clk/sophgo/clk-sg2042-pll.c    |  570 ++++++++++++
 drivers/clk/sophgo/clk-sg2042-rpgate.c |  291 ++++++
 drivers/clk/sophgo/clk-sg2042.h        |   18 +
 6 files changed, 2063 insertions(+)
 create mode 100644 drivers/clk/sophgo/clk-sg2042-clkgen.c
 create mode 100644 drivers/clk/sophgo/clk-sg2042-pll.c
 create mode 100644 drivers/clk/sophgo/clk-sg2042-rpgate.c
 create mode 100644 drivers/clk/sophgo/clk-sg2042.h

diff --git a/drivers/clk/sophgo/Kconfig b/drivers/clk/sophgo/Kconfig
index 1cc49be71bdb..8b1367e3a95e 100644
--- a/drivers/clk/sophgo/Kconfig
+++ b/drivers/clk/sophgo/Kconfig
@@ -9,3 +9,31 @@ config CLK_SOPHGO_CV1800
 	  The driver require a 25MHz Oscillator to function generate clock.
 	  It includes PLLs, common clock function and some vendor clock for
 	  IPs of CV18XX series SoC
+
+config CLK_SOPHGO_SG2042_PLL
+	tristate "Sophgo SG2042 PLL clock support"
+	depends on ARCH_SOPHGO || COMPILE_TEST
+	help
+	  This driver supports the PLL clock controller on the
+	  Sophgo SG2042 SoC. This clock IP uses three oscillators with
+	  frequency of 25 MHz as input, which are used for Main/Fixed
+	  PLL, DDR PLL 0 and DDR PLL 1 respectively.
+
+config CLK_SOPHGO_SG2042_CLKGEN
+	tristate "Sophgo SG2042 Clock Generator support"
+	depends on CLK_SOPHGO_SG2042_PLL
+	help
+	  This driver supports the Clock Generator on the
+	  Sophgo SG2042 SoC. This clock IP depends on SG2042 PLL clock
+	  because it uses PLL clocks as input.
+	  This driver provides clock function such as DIV/Mux/Gate.
+
+config CLK_SOPHGO_SG2042_RPGATE
+	tristate "Sophgo SG2042 RP subsystem clock controller support"
+	depends on CLK_SOPHGO_SG2042_CLKGEN
+	help
+	  This driver supports the RP((Riscv Processors)) subsystem clock
+	  controller on the Sophgo SG2042 SoC.
+	  This clock IP depends on SG2042 Clock Generator because it uses
+	  clock from Clock Generator IP as input.
+	  This driver provides Gate function for RP.
diff --git a/drivers/clk/sophgo/Makefile b/drivers/clk/sophgo/Makefile
index a50320764200..53506845a044 100644
--- a/drivers/clk/sophgo/Makefile
+++ b/drivers/clk/sophgo/Makefile
@@ -5,3 +5,7 @@ clk-sophgo-cv1800-y		+= clk-cv1800.o
 clk-sophgo-cv1800-y		+= clk-cv18xx-common.o
 clk-sophgo-cv1800-y		+= clk-cv18xx-ip.o
 clk-sophgo-cv1800-y		+= clk-cv18xx-pll.o
+
+obj-$(CONFIG_CLK_SOPHGO_SG2042_CLKGEN)	+= clk-sg2042-clkgen.o
+obj-$(CONFIG_CLK_SOPHGO_SG2042_PLL)	+= clk-sg2042-pll.o
+obj-$(CONFIG_CLK_SOPHGO_SG2042_RPGATE)	+= clk-sg2042-rpgate.o
diff --git a/drivers/clk/sophgo/clk-sg2042-clkgen.c b/drivers/clk/sophgo/clk-sg2042-clkgen.c
new file mode 100644
index 000000000000..a334963e83ce
--- /dev/null
+++ b/drivers/clk/sophgo/clk-sg2042-clkgen.c
@@ -0,0 +1,1152 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Sophgo SG2042 Clock Generator Driver
+ *
+ * Copyright (C) 2024 Sophgo Technology Inc.
+ * Copyright (C) 2024 Chen Wang <unicorn_wang@xxxxxxxxxxx>
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <asm/div64.h>
+
+#include <dt-bindings/clock/sophgo,sg2042-clkgen.h>
+
+#include "clk-sg2042.h"
+
+/* Registers defined in SYS_CTRL */
+#define R_PLL_BEGIN		0xC0
+#define R_PLL_STAT		(0xC0 - R_PLL_BEGIN)
+#define R_PLL_CLKEN_CONTROL	(0xC4 - R_PLL_BEGIN)
+#define R_MPLL_CONTROL		(0xE8 - R_PLL_BEGIN)
+#define R_FPLL_CONTROL		(0xF4 - R_PLL_BEGIN)
+#define R_DPLL0_CONTROL		(0xF8 - R_PLL_BEGIN)
+#define R_DPLL1_CONTROL		(0xFC - R_PLL_BEGIN)
+
+/* Registers defined in CLOCK */
+#define R_CLKENREG0		0x00
+#define R_CLKENREG1		0x04
+#define R_CLKSELREG0		0x20
+#define R_CLKDIVREG0		0x40
+#define R_CLKDIVREG1		0x44
+#define R_CLKDIVREG2		0x48
+#define R_CLKDIVREG3		0x4C
+#define R_CLKDIVREG4		0x50
+#define R_CLKDIVREG5		0x54
+#define R_CLKDIVREG6		0x58
+#define R_CLKDIVREG7		0x5C
+#define R_CLKDIVREG8		0x60
+#define R_CLKDIVREG9		0x64
+#define R_CLKDIVREG10		0x68
+#define R_CLKDIVREG11		0x6C
+#define R_CLKDIVREG12		0x70
+#define R_CLKDIVREG13		0x74
+#define R_CLKDIVREG14		0x78
+#define R_CLKDIVREG15		0x7C
+#define R_CLKDIVREG16		0x80
+#define R_CLKDIVREG17		0x84
+#define R_CLKDIVREG18		0x88
+#define R_CLKDIVREG19		0x8C
+#define R_CLKDIVREG20		0x90
+#define R_CLKDIVREG21		0x94
+#define R_CLKDIVREG22		0x98
+#define R_CLKDIVREG23		0x9C
+#define R_CLKDIVREG24		0xA0
+#define R_CLKDIVREG25		0xA4
+#define R_CLKDIVREG26		0xA8
+#define R_CLKDIVREG27		0xAC
+#define R_CLKDIVREG28		0xB0
+#define R_CLKDIVREG29		0xB4
+#define R_CLKDIVREG30		0xB8
+
+/* All following shift value are the same for all DIV registers */
+#define SHIFT_DIV_RESET_CTRL	0
+#define SHIFT_DIV_FACTOR_SEL	3
+#define SHIFT_DIV_FACTOR	16
+
+/**
+ * struct sg2042_divider_clock - Divider clock
+ * @hw:			clk_hw for initialization
+ * @id:			used to map clk_onecell_data
+ * @reg:		used for readl/writel.
+ *			**NOTE**: DIV registers are ALL in CLOCK!
+ * @lock:		spinlock to protect register access, modification of
+ *			frequency can only be served one at the time
+ * @offset_ctrl:	offset of divider control registers
+ * @shift:		shift of "Clock Divider Factor" in divider control register
+ * @width:		width of "Clock Divider Factor" in divider control register
+ * @div_flags:		private flags for this clock, not for framework-specific
+ * @initval:		In the divider control register, we can configure whether
+ *			to use the value of "Clock Divider Factor" or just use
+ *			the initial value pre-configured by IC. BIT[3] controls
+ *			this and by default (value is 0), means initial value
+ *			is used.
+ *			**NOTE** that we cannot read the initial value (default
+ *			value when poweron) and default value of "Clock Divider
+ *			Factor" is zero, which I think is a hardware design flaw
+ *			and should be sync-ed with the initial value. So in
+ *			software we have to add a configuration item (initval)
+ *			to manually configure this value and use it when BIT[3]
+ *			is zero.
+ */
+struct sg2042_divider_clock {
+	struct clk_hw hw;
+
+	unsigned int id;
+
+	void __iomem *reg;
+	/* protect register access */
+	spinlock_t *lock;
+
+	u32 offset_ctrl;
+	u8 shift;
+	u8 width;
+	u8 div_flags;
+	u32 initval;
+};
+
+#define to_sg2042_clk_divider(_hw)	\
+	container_of(_hw, struct sg2042_divider_clock, hw)
+
+/**
+ * struct sg2042_gate_clock - Gate clock
+ * @hw:			clk_hw for initialization
+ * @id:			used to map clk_onecell_data
+ * @offset_enable:	offset of gate enable registers
+ * @bit_idx:		which bit in the register controls gating of this clock
+ */
+struct sg2042_gate_clock {
+	struct clk_hw hw;
+
+	unsigned int id;
+
+	u32 offset_enable;
+	u8 bit_idx;
+};
+
+/**
+ * struct sg2042_mux_clock - Mux clock
+ * @hw:			clk_hw for initialization
+ * @id:			used to map clk_onecell_data
+ * @offset_select:	offset of mux selection registers
+ *			**NOTE**: MUX registers are ALL in CLOCK!
+ * @shift:		shift of "Clock Select" in mux selection register
+ * @width:		width of "Clock Select" in mux selection register
+ * @clk_nb:		used for notification
+ * @original_index:	set by notifier callback
+ */
+struct sg2042_mux_clock {
+	struct clk_hw hw;
+
+	unsigned int id;
+
+	u32 offset_select;
+	u8 shift;
+	u8 width;
+
+	struct notifier_block clk_nb;
+	u8 original_index;
+};
+
+#define to_sg2042_mux_nb(_nb) container_of(_nb, struct sg2042_mux_clock, clk_nb)
+
+static unsigned long sg2042_clk_divider_recalc_rate(struct clk_hw *hw,
+						    unsigned long parent_rate)
+{
+	struct sg2042_divider_clock *divider = to_sg2042_clk_divider(hw);
+	unsigned long ret_rate;
+	u32 val;
+
+	if (!(readl(divider->reg) & BIT(SHIFT_DIV_FACTOR_SEL))) {
+		val = divider->initval;
+	} else {
+		val = readl(divider->reg) >> divider->shift;
+		val &= clk_div_mask(divider->width);
+	}
+
+	ret_rate = divider_recalc_rate(hw, parent_rate, val, NULL,
+				       divider->div_flags, divider->width);
+
+	pr_debug("--> %s: divider_recalc_rate: ret_rate = %ld\n",
+		 clk_hw_get_name(hw), ret_rate);
+	return ret_rate;
+}
+
+static long sg2042_clk_divider_round_rate(struct clk_hw *hw,
+					  unsigned long rate,
+					  unsigned long *prate)
+{
+	struct sg2042_divider_clock *divider = to_sg2042_clk_divider(hw);
+	unsigned long ret_rate;
+	u32 bestdiv;
+
+	/* if read only, just return current value */
+	if (divider->div_flags & CLK_DIVIDER_READ_ONLY) {
+		if (!(readl(divider->reg) & BIT(SHIFT_DIV_FACTOR_SEL))) {
+			bestdiv = divider->initval;
+		} else {
+			bestdiv = readl(divider->reg) >> divider->shift;
+			bestdiv &= clk_div_mask(divider->width);
+		}
+		ret_rate = DIV_ROUND_UP_ULL((u64)*prate, bestdiv);
+	} else {
+		ret_rate = divider_round_rate(hw, rate, prate, NULL,
+					      divider->width, divider->div_flags);
+	}
+
+	pr_debug("--> %s: divider_round_rate: val = %ld\n",
+		 clk_hw_get_name(hw), ret_rate);
+	return ret_rate;
+}
+
+static int sg2042_clk_divider_set_rate(struct clk_hw *hw,
+				       unsigned long rate,
+				       unsigned long parent_rate)
+{
+	struct sg2042_divider_clock *divider = to_sg2042_clk_divider(hw);
+	unsigned long flags = 0;
+	u32 val, val2, value;
+
+	value = divider_get_val(rate, parent_rate, NULL,
+				divider->width, divider->div_flags);
+
+	if (divider->lock)
+		spin_lock_irqsave(divider->lock, flags);
+	else
+		__acquire(divider->lock);
+
+	/*
+	 * The sequence of clock frequency modification is:
+	 * Assert to reset divider.
+	 * Modify the value of Clock Divide Factor (and High Wide if needed).
+	 * De-assert to restore divided clock with new frequency.
+	 */
+	val = readl(divider->reg);
+
+	/* assert */
+	val &= ~BIT(SHIFT_DIV_RESET_CTRL);
+	writel(val, divider->reg);
+
+	if (divider->div_flags & CLK_DIVIDER_HIWORD_MASK) {
+		val = clk_div_mask(divider->width) << (divider->shift + 16);
+	} else {
+		val = readl(divider->reg);
+		val &= ~(clk_div_mask(divider->width) << divider->shift);
+	}
+	val |= value << divider->shift;
+	val |= BIT(SHIFT_DIV_FACTOR_SEL);
+	writel(val, divider->reg);
+	val2 = val;
+
+	/* de-assert */
+	val |= BIT(SHIFT_DIV_RESET_CTRL);
+	writel(val, divider->reg);
+
+	if (divider->lock)
+		spin_unlock_irqrestore(divider->lock, flags);
+	else
+		__release(divider->lock);
+
+	pr_debug("--> %s: divider_set_rate: register val = 0x%x\n",
+		 clk_hw_get_name(hw), val2);
+	return 0;
+}
+
+static const struct clk_ops sg2042_clk_divider_ops = {
+	.recalc_rate = sg2042_clk_divider_recalc_rate,
+	.round_rate = sg2042_clk_divider_round_rate,
+	.set_rate = sg2042_clk_divider_set_rate,
+};
+
+static const struct clk_ops sg2042_clk_divider_ro_ops = {
+	.recalc_rate = sg2042_clk_divider_recalc_rate,
+	.round_rate = sg2042_clk_divider_round_rate,
+};
+
+/*
+ * Clock initialization macro naming rules:
+ * FW: use CLK_HW_INIT_FW_NAME
+ * HW: use CLK_HW_INIT_HW
+ * HWS: use CLK_HW_INIT_HWS
+ * RO: means Read-Only
+ */
+#define SG2042_DIV_FW(_id, _name, _parent,				\
+		      _r_ctrl, _shift, _width,				\
+		      _div_flag, _initval) {				\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_FW_NAME(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_divider_ops,		\
+				0),					\
+		.offset_ctrl = _r_ctrl,					\
+		.shift = _shift,					\
+		.width = _width,					\
+		.div_flags = _div_flag,					\
+		.initval = _initval,					\
+	}
+
+#define SG2042_DIV_FW_RO(_id, _name, _parent,				\
+		  _r_ctrl, _shift, _width,				\
+		  _div_flag, _initval) {				\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_FW_NAME(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_divider_ro_ops,		\
+				0),					\
+		.offset_ctrl = _r_ctrl,					\
+		.shift = _shift,					\
+		.width = _width,					\
+		.div_flags = (_div_flag) | CLK_DIVIDER_READ_ONLY,	\
+		.initval = _initval,					\
+	}
+
+#define SG2042_DIV_HW(_id, _name, _parent,				\
+		      _r_ctrl, _shift, _width,				\
+		      _div_flag, _initval) {				\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_HW(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_divider_ops,		\
+				0),					\
+		.offset_ctrl = _r_ctrl,					\
+		.shift = _shift,					\
+		.width = _width,					\
+		.div_flags = _div_flag,					\
+		.initval = _initval,					\
+	}
+
+#define SG2042_DIV_HW_RO(_id, _name, _parent,				\
+			 _r_ctrl, _shift, _width,			\
+			 _div_flag, _initval) {				\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_HW(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_divider_ro_ops,		\
+				0),					\
+		.offset_ctrl = _r_ctrl,					\
+		.shift = _shift,					\
+		.width = _width,					\
+		.div_flags = (_div_flag) | CLK_DIVIDER_READ_ONLY,	\
+		.initval = _initval,					\
+	}
+
+#define SG2042_DIV_HWS(_id, _name, _parent,				\
+		       _r_ctrl, _shift, _width,				\
+		       _div_flag, _initval) {				\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_HWS(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_divider_ops,		\
+				0),					\
+		.offset_ctrl = _r_ctrl,					\
+		.shift = _shift,					\
+		.width = _width,					\
+		.div_flags = _div_flag,					\
+		.initval = _initval,					\
+	}
+
+#define SG2042_DIV_HWS_RO(_id, _name, _parent,				\
+			  _r_ctrl, _shift, _width,			\
+			  _div_flag, _initval) {			\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_HWS(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_divider_ro_ops,		\
+				0),					\
+		.offset_ctrl = _r_ctrl,					\
+		.shift = _shift,					\
+		.width = _width,					\
+		.div_flags = (_div_flag) | CLK_DIVIDER_READ_ONLY,	\
+		.initval = _initval,					\
+	}
+
+#define SG2042_GATE_HWS(_id, _name, _parent, _flags,	\
+			_r_enable, _bit_idx) {		\
+		.id = _id,				\
+		.hw.init = CLK_HW_INIT_HWS(		\
+				_name,			\
+				_parent,		\
+				NULL,			\
+				_flags),		\
+		.offset_enable = _r_enable,		\
+		.bit_idx = _bit_idx,			\
+	}
+
+#define SG2042_GATE_HW(_id, _name, _parent, _flags,	\
+		       _r_enable, _bit_idx) {		\
+		.id = _id,				\
+		.hw.init = CLK_HW_INIT_HW(		\
+				_name,			\
+				_parent,		\
+				NULL,			\
+				_flags),		\
+		.offset_enable = _r_enable,		\
+		.bit_idx = _bit_idx,			\
+	}
+
+#define SG2042_GATE_FW(_id, _name, _parent, _flags,	\
+		       _r_enable, _bit_idx) {		\
+		.id = _id,				\
+		.hw.init = CLK_HW_INIT_FW_NAME(		\
+				_name,			\
+				_parent,		\
+				NULL,			\
+				_flags),		\
+		.offset_enable = _r_enable,		\
+		.bit_idx = _bit_idx,			\
+	}
+
+#define SG2042_MUX(_id, _name, _parents, _flags, _r_select, _shift, _width) { \
+		.id = _id,					\
+		.hw.init = CLK_HW_INIT_PARENTS_HW(		\
+				_name,				\
+				_parents,			\
+				NULL,				\
+				_flags),			\
+		.offset_select = _r_select,			\
+		.shift = _shift,				\
+		.width = _width,				\
+	}
+
+/*
+ * Clock items in the array are sorted according to the clock-tree diagram,
+ * from top to bottom, from upstream to downstream. Read TRM for details.
+ */
+
+/* updated during probe/registration */
+static const struct clk_hw *clk_gate_ddr01_div0[] = { NULL };
+static const struct clk_hw *clk_gate_ddr01_div1[] = { NULL };
+static const struct clk_hw *clk_gate_ddr23_div0[] = { NULL };
+static const struct clk_hw *clk_gate_ddr23_div1[] = { NULL };
+static const struct clk_hw *clk_gate_rp_cpu_normal_div0[] = { NULL };
+static const struct clk_hw *clk_gate_rp_cpu_normal_div1[] = { NULL };
+static const struct clk_hw *clk_gate_axi_ddr_div0[] = { NULL };
+static const struct clk_hw *clk_gate_axi_ddr_div1[] = { NULL };
+
+static const struct sg2042_gate_clock sg2042_gate_clks_level_1[] = {
+	SG2042_GATE_FW(GATE_CLK_DDR01_DIV0, "clk_gate_ddr01_div0", "dpll0",
+		       CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+		       R_CLKDIVREG27, 4),
+	SG2042_GATE_FW(GATE_CLK_DDR01_DIV1, "clk_gate_ddr01_div1", "fpll",
+		       CLK_IS_CRITICAL,
+		       R_CLKDIVREG28, 4),
+
+	SG2042_GATE_FW(GATE_CLK_DDR23_DIV0, "clk_gate_ddr23_div0", "dpll1",
+		       CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+		       R_CLKDIVREG29, 4),
+	SG2042_GATE_FW(GATE_CLK_DDR23_DIV1, "clk_gate_ddr23_div1", "fpll",
+		       CLK_IS_CRITICAL,
+		       R_CLKDIVREG30, 4),
+
+	SG2042_GATE_FW(GATE_CLK_RP_CPU_NORMAL_DIV0,
+		       "clk_gate_rp_cpu_normal_div0", "mpll",
+		       CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+		       R_CLKDIVREG0, 4),
+	SG2042_GATE_FW(GATE_CLK_RP_CPU_NORMAL_DIV1,
+		       "clk_gate_rp_cpu_normal_div1", "fpll",
+		       CLK_IS_CRITICAL,
+		       R_CLKDIVREG1, 4),
+
+	SG2042_GATE_FW(GATE_CLK_AXI_DDR_DIV0, "clk_gate_axi_ddr_div0", "mpll",
+		       CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+		       R_CLKDIVREG25, 4),
+	SG2042_GATE_FW(GATE_CLK_AXI_DDR_DIV1, "clk_gate_axi_ddr_div1", "fpll",
+		       CLK_IS_CRITICAL,
+		       R_CLKDIVREG26, 4),
+};
+
+#define DEF_DIVFLAG (CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO)
+
+static struct sg2042_divider_clock sg2042_div_clks_level_1[] = {
+	SG2042_DIV_HWS_RO(DIV_CLK_DPLL0_DDR01_0,
+			  "clk_div_ddr01_0", clk_gate_ddr01_div0,
+			  R_CLKDIVREG27, 16, 5, DEF_DIVFLAG, 1),
+	SG2042_DIV_HWS_RO(DIV_CLK_FPLL_DDR01_1,
+			  "clk_div_ddr01_1", clk_gate_ddr01_div1,
+			  R_CLKDIVREG28, 16, 5, DEF_DIVFLAG, 1),
+
+	SG2042_DIV_HWS_RO(DIV_CLK_DPLL1_DDR23_0,
+			  "clk_div_ddr23_0", clk_gate_ddr23_div0,
+			  R_CLKDIVREG29, 16, 5, DEF_DIVFLAG, 1),
+	SG2042_DIV_HWS_RO(DIV_CLK_FPLL_DDR23_1,
+			  "clk_div_ddr23_1", clk_gate_ddr23_div1,
+			  R_CLKDIVREG30, 16, 5, DEF_DIVFLAG, 1),
+
+	SG2042_DIV_HWS(DIV_CLK_MPLL_RP_CPU_NORMAL_0,
+		       "clk_div_rp_cpu_normal_0", clk_gate_rp_cpu_normal_div0,
+		       R_CLKDIVREG0, 16, 5, DEF_DIVFLAG, 1),
+	SG2042_DIV_HWS(DIV_CLK_FPLL_RP_CPU_NORMAL_1,
+		       "clk_div_rp_cpu_normal_1", clk_gate_rp_cpu_normal_div1,
+		       R_CLKDIVREG1, 16, 5, DEF_DIVFLAG, 1),
+
+	SG2042_DIV_HWS(DIV_CLK_MPLL_AXI_DDR_0,
+		       "clk_div_axi_ddr_0", clk_gate_axi_ddr_div0,
+		       R_CLKDIVREG25, 16, 5, DEF_DIVFLAG, 2),
+	SG2042_DIV_HWS(DIV_CLK_FPLL_AXI_DDR_1,
+		       "clk_div_axi_ddr_1", clk_gate_axi_ddr_div1,
+		       R_CLKDIVREG26, 16, 5, DEF_DIVFLAG, 1),
+};
+
+/*
+ * Note: regarding names for mux clock, "0/1" or "div0/div1" means the
+ * first/second parent input source, not the register value.
+ * For example:
+ * "clk_div_ddr01_0" is the name of Clock divider 0 control of DDR01, and
+ * "clk_gate_ddr01_div0" is the gate clock in front of the "clk_div_ddr01_0",
+ * they are both controlled by register CLKDIVREG27;
+ * "clk_div_ddr01_1" is the name of Clock divider 1 control of DDR01, and
+ * "clk_gate_ddr01_div1" is the gate clock in front of the "clk_div_ddr01_1",
+ * they are both controlled by register CLKDIVREG28;
+ * While for register value of mux selection, use Clock Select for DDR01’s clock
+ * as example, see CLKSELREG0, bit[2].
+ * 1: Select in_dpll0_clk as clock source, correspondng to the parent input
+ *    source from "clk_div_ddr01_0".
+ * 0: Select in_fpll_clk as clock source, corresponding to the parent input
+ *    source from "clk_div_ddr01_1".
+ * So we need a table to define the array of register values corresponding to
+ * the parent index and tell CCF about this when registering mux clock.
+ */
+static const u32 sg2042_mux_table[] = {1, 0};
+
+/* Aliases just for easy reading */
+#define clk_div_ddr01_0		(&sg2042_div_clks_level_1[0].hw)
+#define clk_div_ddr01_1		(&sg2042_div_clks_level_1[1].hw)
+#define clk_div_ddr23_0		(&sg2042_div_clks_level_1[2].hw)
+#define clk_div_ddr23_1		(&sg2042_div_clks_level_1[3].hw)
+#define clk_div_rp_cpu_normal_0	(&sg2042_div_clks_level_1[4].hw)
+#define clk_div_rp_cpu_normal_1	(&sg2042_div_clks_level_1[5].hw)
+#define clk_div_axi_ddr_0	(&sg2042_div_clks_level_1[6].hw)
+#define clk_div_axi_ddr_1	(&sg2042_div_clks_level_1[7].hw)
+
+static const struct clk_hw *clk_mux_ddr01_p[] = {
+	clk_div_ddr01_0,
+	clk_div_ddr01_1,
+};
+
+static const struct clk_hw *clk_mux_ddr23_p[] = {
+	clk_div_ddr23_0,
+	clk_div_ddr23_1,
+};
+
+static const struct clk_hw *clk_mux_rp_cpu_normal_p[] = {
+	clk_div_rp_cpu_normal_0,
+	clk_div_rp_cpu_normal_1,
+};
+
+static const struct clk_hw *clk_mux_axi_ddr_p[] = {
+	clk_div_axi_ddr_0,
+	clk_div_axi_ddr_1,
+};
+
+/* Mux clocks to be updated during probe/registration */
+static const struct clk_hw *clk_mux_ddr01[] = { NULL };
+static const struct clk_hw *clk_mux_ddr23[] = { NULL };
+static const struct clk_hw *clk_mux_rp_cpu_normal[] = { NULL };
+static const struct clk_hw *clk_mux_axi_ddr[] = { NULL };
+
+static struct sg2042_mux_clock sg2042_mux_clks[] = {
+	SG2042_MUX(MUX_CLK_DDR01, "clk_mux_ddr01", clk_mux_ddr01_p,
+		   CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT | CLK_MUX_READ_ONLY,
+		   R_CLKSELREG0, 2, 1),
+	SG2042_MUX(MUX_CLK_DDR23, "clk_mux_ddr23", clk_mux_ddr23_p,
+		   CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT | CLK_MUX_READ_ONLY,
+		   R_CLKSELREG0, 3, 1),
+	SG2042_MUX(MUX_CLK_RP_CPU_NORMAL, "clk_mux_rp_cpu_normal", clk_mux_rp_cpu_normal_p,
+		   CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+		   R_CLKSELREG0, 0, 1),
+	SG2042_MUX(MUX_CLK_AXI_DDR, "clk_mux_axi_ddr", clk_mux_axi_ddr_p,
+		   CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
+		   R_CLKSELREG0, 1, 1),
+};
+
+/* Aliases just for easy reading */
+#define clk_div_top_rp_cmn_div2	(&sg2042_div_clks_level_2[0].hw)
+#define clk_div_50m_a53		(&sg2042_div_clks_level_2[1].hw)
+#define clk_div_timer1		(&sg2042_div_clks_level_2[2].hw)
+#define clk_div_timer2		(&sg2042_div_clks_level_2[3].hw)
+#define clk_div_timer3		(&sg2042_div_clks_level_2[4].hw)
+#define clk_div_timer4		(&sg2042_div_clks_level_2[5].hw)
+#define clk_div_timer5		(&sg2042_div_clks_level_2[6].hw)
+#define clk_div_timer6		(&sg2042_div_clks_level_2[7].hw)
+#define clk_div_timer7		(&sg2042_div_clks_level_2[8].hw)
+#define clk_div_timer8		(&sg2042_div_clks_level_2[9].hw)
+#define clk_div_uart_500m	(&sg2042_div_clks_level_2[10].hw)
+#define clk_div_ahb_lpc		(&sg2042_div_clks_level_2[11].hw)
+#define clk_div_efuse		(&sg2042_div_clks_level_2[12].hw)
+#define clk_div_tx_eth0		(&sg2042_div_clks_level_2[13].hw)
+#define clk_div_ptp_ref_i_eth0	(&sg2042_div_clks_level_2[14].hw)
+#define clk_div_ref_eth0	(&sg2042_div_clks_level_2[15].hw)
+#define clk_div_emmc		(&sg2042_div_clks_level_2[16].hw)
+#define clk_div_sd		(&sg2042_div_clks_level_2[17].hw)
+#define clk_div_top_axi0	(&sg2042_div_clks_level_2[18].hw)
+#define clk_div_100k_emmc	(&sg2042_div_clks_level_2[19].hw)
+#define clk_div_100k_sd		(&sg2042_div_clks_level_2[20].hw)
+#define clk_div_gpio_db		(&sg2042_div_clks_level_2[21].hw)
+#define clk_div_top_axi_hsperi	(&sg2042_div_clks_level_2[22].hw)
+
+static struct sg2042_divider_clock sg2042_div_clks_level_2[] = {
+	SG2042_DIV_HWS(DIV_CLK_FPLL_TOP_RP_CMN_DIV2,
+		       "clk_div_top_rp_cmn_div2", clk_mux_rp_cpu_normal,
+		       R_CLKDIVREG3, 16, 16, DEF_DIVFLAG, 2),
+
+	SG2042_DIV_FW(DIV_CLK_FPLL_50M_A53, "clk_div_50m_a53", "fpll",
+		      R_CLKDIVREG2, 16, 8, DEF_DIVFLAG, 20),
+	/* downstream of div_50m_a53 */
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER1, "clk_div_timer1", clk_div_50m_a53,
+		      R_CLKDIVREG6, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER2, "clk_div_timer2", clk_div_50m_a53,
+		      R_CLKDIVREG7, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER3, "clk_div_timer3", clk_div_50m_a53,
+		      R_CLKDIVREG8, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER4, "clk_div_timer4", clk_div_50m_a53,
+		      R_CLKDIVREG9, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER5, "clk_div_timer5", clk_div_50m_a53,
+		      R_CLKDIVREG10, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER6, "clk_div_timer6", clk_div_50m_a53,
+		      R_CLKDIVREG11, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER7, "clk_div_timer7", clk_div_50m_a53,
+		      R_CLKDIVREG12, 16, 16, DEF_DIVFLAG, 1),
+	SG2042_DIV_HW(DIV_CLK_FPLL_DIV_TIMER8, "clk_div_timer8", clk_div_50m_a53,
+		      R_CLKDIVREG13, 16, 16, DEF_DIVFLAG, 1),
+
+	/*
+	 * Set clk_div_uart_500m as RO, because the width of CLKDIVREG4 is too
+	 * narrow for us to produce 115200. Use UART internal divider directly.
+	 */
+	SG2042_DIV_FW_RO(DIV_CLK_FPLL_UART_500M, "clk_div_uart_500m", "fpll",
+			 R_CLKDIVREG4, 16, 7, DEF_DIVFLAG, 2),
+	SG2042_DIV_FW(DIV_CLK_FPLL_AHB_LPC, "clk_div_ahb_lpc", "fpll",
+		      R_CLKDIVREG5, 16, 16, DEF_DIVFLAG, 5),
+	SG2042_DIV_FW(DIV_CLK_FPLL_EFUSE, "clk_div_efuse", "fpll",
+		      R_CLKDIVREG14, 16, 7, DEF_DIVFLAG, 40),
+	SG2042_DIV_FW(DIV_CLK_FPLL_TX_ETH0, "clk_div_tx_eth0", "fpll",
+		      R_CLKDIVREG16, 16, 11, DEF_DIVFLAG, 8),
+	SG2042_DIV_FW(DIV_CLK_FPLL_PTP_REF_I_ETH0,
+		      "clk_div_ptp_ref_i_eth0", "fpll",
+		      R_CLKDIVREG17, 16, 8, DEF_DIVFLAG, 20),
+	SG2042_DIV_FW(DIV_CLK_FPLL_REF_ETH0, "clk_div_ref_eth0", "fpll",
+		      R_CLKDIVREG18, 16, 8, DEF_DIVFLAG, 40),
+	SG2042_DIV_FW(DIV_CLK_FPLL_EMMC, "clk_div_emmc", "fpll",
+		      R_CLKDIVREG19, 16, 5, DEF_DIVFLAG, 10),
+	SG2042_DIV_FW(DIV_CLK_FPLL_SD, "clk_div_sd", "fpll",
+		      R_CLKDIVREG21, 16, 5, DEF_DIVFLAG, 10),
+
+	SG2042_DIV_FW(DIV_CLK_FPLL_TOP_AXI0, "clk_div_top_axi0", "fpll",
+		      R_CLKDIVREG23, 16, 5, DEF_DIVFLAG, 10),
+	/* downstream of div_top_axi0 */
+	SG2042_DIV_HW(DIV_CLK_FPLL_100K_EMMC, "clk_div_100k_emmc", clk_div_top_axi0,
+		      R_CLKDIVREG20, 16, 16, DEF_DIVFLAG, 1000),
+	SG2042_DIV_HW(DIV_CLK_FPLL_100K_SD, "clk_div_100k_sd", clk_div_top_axi0,
+		      R_CLKDIVREG22, 16, 16, DEF_DIVFLAG, 1000),
+	SG2042_DIV_HW(DIV_CLK_FPLL_GPIO_DB, "clk_div_gpio_db", clk_div_top_axi0,
+		      R_CLKDIVREG15, 16, 16, DEF_DIVFLAG, 1000),
+
+	SG2042_DIV_FW(DIV_CLK_FPLL_TOP_AXI_HSPERI,
+		      "clk_div_top_axi_hsperi", "fpll",
+		      R_CLKDIVREG24, 16, 5, DEF_DIVFLAG, 4),
+};
+
+/* Gate clocks to be updated during probe/registration */
+static const struct clk_hw *clk_gate_rp_cpu_normal[] = { NULL };
+static const struct clk_hw *clk_gate_top_rp_cmn_div2[] = { NULL };
+
+static const struct sg2042_gate_clock sg2042_gate_clks_level_2[] = {
+	SG2042_GATE_HWS(GATE_CLK_DDR01, "clk_gate_ddr01", clk_mux_ddr01,
+			CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+			R_CLKENREG1, 14),
+
+	SG2042_GATE_HWS(GATE_CLK_DDR23, "clk_gate_ddr23", clk_mux_ddr23,
+			CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+			R_CLKENREG1, 15),
+
+	SG2042_GATE_HWS(GATE_CLK_RP_CPU_NORMAL,
+			"clk_gate_rp_cpu_normal", clk_mux_rp_cpu_normal,
+			CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+			R_CLKENREG0, 0),
+
+	SG2042_GATE_HWS(GATE_CLK_AXI_DDR, "clk_gate_axi_ddr", clk_mux_axi_ddr,
+			CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+			R_CLKENREG1, 13),
+
+	/* upon are gate clocks directly downstream of muxes */
+
+	/* downstream of clk_div_top_rp_cmn_div2 */
+	SG2042_GATE_HW(GATE_CLK_TOP_RP_CMN_DIV2,
+		       "clk_gate_top_rp_cmn_div2", clk_div_top_rp_cmn_div2,
+		       CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, R_CLKENREG0, 2),
+	SG2042_GATE_HWS(GATE_CLK_HSDMA, "clk_gate_hsdma", clk_gate_top_rp_cmn_div2,
+			CLK_SET_RATE_PARENT, R_CLKENREG1, 10),
+
+	/*
+	 * downstream of clk_gate_rp_cpu_normal
+	 *
+	 * FIXME: there should be one 1/2 DIV between clk_gate_rp_cpu_normal
+	 * and clk_gate_axi_pcie0/clk_gate_axi_pcie1.
+	 * But the 1/2 DIV is fixed and no configurable register exported, so
+	 * when reading from these two clocks, the rate value are still the
+	 * same as that of clk_gate_rp_cpu_normal, it's not correct.
+	 * This just affects the value read.
+	 */
+	SG2042_GATE_HWS(GATE_CLK_AXI_PCIE0,
+			"clk_gate_axi_pcie0", clk_gate_rp_cpu_normal,
+			CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, R_CLKENREG1, 8),
+	SG2042_GATE_HWS(GATE_CLK_AXI_PCIE1,
+			"clk_gate_axi_pcie1", clk_gate_rp_cpu_normal,
+			CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, R_CLKENREG1, 9),
+
+	/* downstream of div_50m_a53 */
+	SG2042_GATE_HW(GATE_CLK_A53_50M, "clk_gate_a53_50m", clk_div_50m_a53,
+		       CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, R_CLKENREG0, 1),
+	SG2042_GATE_HW(GATE_CLK_TIMER1, "clk_gate_timer1", clk_div_timer1,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 12),
+	SG2042_GATE_HW(GATE_CLK_TIMER2, "clk_gate_timer2", clk_div_timer2,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 13),
+	SG2042_GATE_HW(GATE_CLK_TIMER3, "clk_gate_timer3", clk_div_timer3,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 14),
+	SG2042_GATE_HW(GATE_CLK_TIMER4, "clk_gate_timer4", clk_div_timer4,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 15),
+	SG2042_GATE_HW(GATE_CLK_TIMER5, "clk_gate_timer5", clk_div_timer5,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 16),
+	SG2042_GATE_HW(GATE_CLK_TIMER6, "clk_gate_timer6", clk_div_timer6,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 17),
+	SG2042_GATE_HW(GATE_CLK_TIMER7, "clk_gate_timer7", clk_div_timer7,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 18),
+	SG2042_GATE_HW(GATE_CLK_TIMER8, "clk_gate_timer8", clk_div_timer8,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 19),
+
+	/* gate clocks downstream from div clocks one-to-one */
+	SG2042_GATE_HW(GATE_CLK_UART_500M, "clk_gate_uart_500m", clk_div_uart_500m,
+		       CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, R_CLKENREG0, 4),
+	SG2042_GATE_HW(GATE_CLK_AHB_LPC, "clk_gate_ahb_lpc", clk_div_ahb_lpc,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 7),
+	SG2042_GATE_HW(GATE_CLK_EFUSE, "clk_gate_efuse", clk_div_efuse,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 20),
+	SG2042_GATE_HW(GATE_CLK_TX_ETH0, "clk_gate_tx_eth0", clk_div_tx_eth0,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 30),
+	SG2042_GATE_HW(GATE_CLK_PTP_REF_I_ETH0,
+		       "clk_gate_ptp_ref_i_eth0", clk_div_ptp_ref_i_eth0,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 0),
+	SG2042_GATE_HW(GATE_CLK_REF_ETH0, "clk_gate_ref_eth0", clk_div_ref_eth0,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 1),
+	SG2042_GATE_HW(GATE_CLK_EMMC_100M, "clk_gate_emmc", clk_div_emmc,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 3),
+	SG2042_GATE_HW(GATE_CLK_SD_100M, "clk_gate_sd", clk_div_sd,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 6),
+
+	/* downstream of clk_div_top_axi0 */
+	SG2042_GATE_HW(GATE_CLK_AHB_ROM, "clk_gate_ahb_rom", clk_div_top_axi0,
+		       0, R_CLKENREG0, 8),
+	SG2042_GATE_HW(GATE_CLK_AHB_SF, "clk_gate_ahb_sf", clk_div_top_axi0,
+		       0, R_CLKENREG0, 9),
+	SG2042_GATE_HW(GATE_CLK_AXI_SRAM, "clk_gate_axi_sram", clk_div_top_axi0,
+		       CLK_IGNORE_UNUSED, R_CLKENREG0, 10),
+	SG2042_GATE_HW(GATE_CLK_APB_TIMER, "clk_gate_apb_timer", clk_div_top_axi0,
+		       CLK_IGNORE_UNUSED, R_CLKENREG0, 11),
+	SG2042_GATE_HW(GATE_CLK_APB_EFUSE, "clk_gate_apb_efuse", clk_div_top_axi0,
+		       0, R_CLKENREG0, 21),
+	SG2042_GATE_HW(GATE_CLK_APB_GPIO, "clk_gate_apb_gpio", clk_div_top_axi0,
+		       0, R_CLKENREG0, 22),
+	SG2042_GATE_HW(GATE_CLK_APB_GPIO_INTR,
+		       "clk_gate_apb_gpio_intr", clk_div_top_axi0,
+		       CLK_IS_CRITICAL, R_CLKENREG0, 23),
+	SG2042_GATE_HW(GATE_CLK_APB_I2C, "clk_gate_apb_i2c", clk_div_top_axi0,
+		       0, R_CLKENREG0, 26),
+	SG2042_GATE_HW(GATE_CLK_APB_WDT, "clk_gate_apb_wdt", clk_div_top_axi0,
+		       0, R_CLKENREG0, 27),
+	SG2042_GATE_HW(GATE_CLK_APB_PWM, "clk_gate_apb_pwm", clk_div_top_axi0,
+		       0, R_CLKENREG0, 28),
+	SG2042_GATE_HW(GATE_CLK_APB_RTC, "clk_gate_apb_rtc", clk_div_top_axi0,
+		       0, R_CLKENREG0, 29),
+	SG2042_GATE_HW(GATE_CLK_TOP_AXI0, "clk_gate_top_axi0", clk_div_top_axi0,
+		       CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+		       R_CLKENREG1, 11),
+	/* downstream of DIV clocks which are sourced from clk_div_top_axi0 */
+	SG2042_GATE_HW(GATE_CLK_GPIO_DB, "clk_gate_gpio_db", clk_div_gpio_db,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 24),
+	SG2042_GATE_HW(GATE_CLK_100K_EMMC, "clk_gate_100k_emmc", clk_div_100k_emmc,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 4),
+	SG2042_GATE_HW(GATE_CLK_100K_SD, "clk_gate_100k_sd", clk_div_100k_sd,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 7),
+
+	/* downstream of clk_div_top_axi_hsperi */
+	SG2042_GATE_HW(GATE_CLK_SYSDMA_AXI,
+		       "clk_gate_sysdma_axi", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 3),
+	SG2042_GATE_HW(GATE_CLK_APB_UART,
+		       "clk_gate_apb_uart", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 5),
+	SG2042_GATE_HW(GATE_CLK_AXI_DBG_I2C,
+		       "clk_gate_axi_dbg_i2c", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 6),
+	SG2042_GATE_HW(GATE_CLK_APB_SPI,
+		       "clk_gate_apb_spi", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 25),
+	SG2042_GATE_HW(GATE_CLK_AXI_ETH0,
+		       "clk_gate_axi_eth0", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG0, 31),
+	SG2042_GATE_HW(GATE_CLK_AXI_EMMC,
+		       "clk_gate_axi_emmc", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 2),
+	SG2042_GATE_HW(GATE_CLK_AXI_SD,
+		       "clk_gate_axi_sd", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT, R_CLKENREG1, 5),
+	SG2042_GATE_HW(GATE_CLK_TOP_AXI_HSPERI,
+		       "clk_gate_top_axi_hsperi", clk_div_top_axi_hsperi,
+		       CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+		       R_CLKENREG1, 12),
+};
+
+static DEFINE_SPINLOCK(sg2042_clk_lock);
+
+static int sg2042_clk_register_divs(struct device *dev,
+				    struct sg2042_clk_data *clk_data,
+				    struct sg2042_divider_clock div_clks[],
+				    int num_div_clks)
+{
+	struct sg2042_divider_clock *div;
+	struct clk_hw *hw;
+	int i, ret = 0;
+
+	for (i = 0; i < num_div_clks; i++) {
+		div = &div_clks[i];
+
+		if (div->div_flags & CLK_DIVIDER_HIWORD_MASK) {
+			if (div->width + div->shift > 16) {
+				pr_warn("divider value exceeds LOWORD field\n");
+				ret = -EINVAL;
+				break;
+			}
+		}
+
+		div->reg = clk_data->iobase + div->offset_ctrl;
+		div->lock = &sg2042_clk_lock;
+
+		hw = &div->hw;
+		ret = devm_clk_hw_register(dev, hw);
+		if (ret) {
+			pr_err("failed to register clock %s\n", div->hw.init->name);
+			break;
+		}
+
+		clk_data->onecell_data.hws[div->id] = hw;
+	}
+
+	return ret;
+}
+
+static int sg2042_clk_register_gates(struct device *dev,
+				     struct sg2042_clk_data *clk_data,
+				     const struct sg2042_gate_clock gate_clks[],
+				     int num_gate_clks)
+{
+	const struct sg2042_gate_clock *gate;
+	struct clk_hw *hw;
+	int i, ret = 0;
+
+	for (i = 0; i < num_gate_clks; i++) {
+		gate = &gate_clks[i];
+		hw = __devm_clk_hw_register_gate
+			(dev,
+			 NULL,
+			 gate->hw.init->name,
+			 NULL,
+			 gate->hw.init->parent_hws[0],
+			 NULL,
+			 gate->hw.init->flags,
+			 clk_data->iobase + gate->offset_enable,
+			 gate->bit_idx,
+			 0,
+			 &sg2042_clk_lock);
+		if (IS_ERR(hw)) {
+			pr_err("failed to register clock %s\n", gate->hw.init->name);
+			ret = PTR_ERR(hw);
+			break;
+		}
+
+		clk_data->onecell_data.hws[gate->id] = hw;
+
+		/* Updated some clocks which take the role of parent */
+		switch (gate->id) {
+		case GATE_CLK_RP_CPU_NORMAL:
+			*clk_gate_rp_cpu_normal = hw;
+			break;
+		case GATE_CLK_TOP_RP_CMN_DIV2:
+			*clk_gate_top_rp_cmn_div2 = hw;
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int sg2042_clk_register_gates_fw(struct device *dev,
+					struct sg2042_clk_data *clk_data,
+					const struct sg2042_gate_clock gate_clks[],
+					int num_gate_clks)
+{
+	const struct sg2042_gate_clock *gate;
+	struct clk_hw *hw;
+	int i, ret = 0;
+
+	for (i = 0; i < num_gate_clks; i++) {
+		gate = &gate_clks[i];
+		hw = devm_clk_hw_register_gate_parent_data
+			(dev,
+			 gate->hw.init->name,
+			 gate->hw.init->parent_data,
+			 gate->hw.init->flags,
+			 clk_data->iobase + gate->offset_enable,
+			 gate->bit_idx,
+			 0,
+			 &sg2042_clk_lock);
+		if (IS_ERR(hw)) {
+			pr_err("failed to register clock %s\n", gate->hw.init->name);
+			ret = PTR_ERR(hw);
+			break;
+		}
+
+		clk_data->onecell_data.hws[gate->id] = hw;
+
+		/* Updated some clocks which take the role of parent */
+		switch (gate->id) {
+		case GATE_CLK_DDR01_DIV0:
+			*clk_gate_ddr01_div0 = hw;
+			break;
+		case GATE_CLK_DDR01_DIV1:
+			*clk_gate_ddr01_div1 = hw;
+			break;
+		case GATE_CLK_DDR23_DIV0:
+			*clk_gate_ddr23_div0 = hw;
+			break;
+		case GATE_CLK_DDR23_DIV1:
+			*clk_gate_ddr23_div1 = hw;
+			break;
+		case GATE_CLK_RP_CPU_NORMAL_DIV0:
+			*clk_gate_rp_cpu_normal_div0 = hw;
+			break;
+		case GATE_CLK_RP_CPU_NORMAL_DIV1:
+			*clk_gate_rp_cpu_normal_div1 = hw;
+			break;
+		case GATE_CLK_AXI_DDR_DIV0:
+			*clk_gate_axi_ddr_div0 = hw;
+			break;
+		case GATE_CLK_AXI_DDR_DIV1:
+			*clk_gate_axi_ddr_div1 = hw;
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int sg2042_mux_notifier_cb(struct notifier_block *nb,
+				  unsigned long event,
+				  void *data)
+{
+	struct sg2042_mux_clock *mux = to_sg2042_mux_nb(nb);
+	const struct clk_ops *ops = &clk_mux_ops;
+	struct clk_notifier_data *ndata = data;
+	struct clk_hw *hw;
+	int ret = 0;
+
+	hw = __clk_get_hw(ndata->clk);
+
+	/* To switch to fpll before changing rate and restore after that */
+	if (event == PRE_RATE_CHANGE) {
+		mux->original_index = ops->get_parent(hw);
+
+		/*
+		 * "1" is the array index of the second parent input source of
+		 * mux. For SG2042, it's fpll for all mux clocks.
+		 * "0" is the array index of the frist parent input source of
+		 * mux, For SG2042, it's mpll.
+		 * FIXME, any good idea to avoid magic number?
+		 */
+		if (mux->original_index == 0)
+			ret = ops->set_parent(hw, 1);
+	} else if (event == POST_RATE_CHANGE) {
+		ret = ops->set_parent(hw, mux->original_index);
+	}
+
+	return notifier_from_errno(ret);
+}
+
+static int sg2042_clk_register_muxs(struct device *dev,
+				    struct sg2042_clk_data *clk_data,
+				    struct sg2042_mux_clock mux_clks[],
+				    int num_mux_clks)
+{
+	struct sg2042_mux_clock *mux;
+	struct clk_hw *hw;
+	int i, ret = 0;
+
+	for (i = 0; i < num_mux_clks; i++) {
+		mux = &mux_clks[i];
+
+		hw = __devm_clk_hw_register_mux
+			(dev,
+			 NULL,
+			 mux->hw.init->name,
+			 mux->hw.init->num_parents,
+			 NULL,
+			 mux->hw.init->parent_hws,
+			 NULL,
+			 mux->hw.init->flags,
+			 clk_data->iobase + mux->offset_select,
+			 mux->shift,
+			 BIT(mux->width) - 1,
+			 0,
+			 sg2042_mux_table,
+			 &sg2042_clk_lock);
+		if (IS_ERR(hw)) {
+			pr_err("failed to register clock %s\n", mux->hw.init->name);
+			ret = PTR_ERR(hw);
+			break;
+		}
+
+		clk_data->onecell_data.hws[mux->id] = hw;
+
+		/* Updated some clocks which takes the role of parent */
+		switch (mux->id) {
+		case MUX_CLK_DDR01:
+			*clk_mux_ddr01 = hw;
+			break;
+		case MUX_CLK_DDR23:
+			*clk_mux_ddr23 = hw;
+			break;
+		case MUX_CLK_RP_CPU_NORMAL:
+			*clk_mux_rp_cpu_normal = hw;
+			break;
+		case MUX_CLK_AXI_DDR:
+			*clk_mux_axi_ddr = hw;
+			break;
+		}
+
+		/*
+		 * FIXME: Theoretically, we should set parent for the
+		 * mux, but seems hardware has done this for us with
+		 * default value, so we don't set parent again here.
+		 */
+
+		if (!(mux->hw.init->flags & CLK_MUX_READ_ONLY)) {
+			mux->clk_nb.notifier_call = sg2042_mux_notifier_cb;
+			ret = devm_clk_notifier_register(dev, hw->clk, &mux->clk_nb);
+			if (ret) {
+				pr_err("failed to register clock notifier for %s\n",
+				       mux->hw.init->name);
+				break;
+			}
+		}
+	}
+
+	return ret;
+}
+
+static int sg2042_init_clkdata(struct platform_device *pdev,
+			       int num_clks,
+			       struct sg2042_clk_data **pp_clk_data)
+{
+	struct sg2042_clk_data *clk_data = NULL;
+
+	clk_data = devm_kzalloc(&pdev->dev,
+				struct_size(clk_data, onecell_data.hws, num_clks),
+				GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->iobase = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(clk_data->iobase)))
+		return PTR_ERR(clk_data->iobase);
+
+	clk_data->onecell_data.num = num_clks;
+
+	*pp_clk_data = clk_data;
+
+	return 0;
+}
+
+static int sg2042_clkgen_probe(struct platform_device *pdev)
+{
+	struct sg2042_clk_data *clk_data = NULL;
+	int num_clks;
+	int ret;
+
+	num_clks = ARRAY_SIZE(sg2042_div_clks_level_1) +
+		   ARRAY_SIZE(sg2042_div_clks_level_2) +
+		   ARRAY_SIZE(sg2042_gate_clks_level_1) +
+		   ARRAY_SIZE(sg2042_gate_clks_level_2) +
+		   ARRAY_SIZE(sg2042_mux_clks);
+
+	ret = sg2042_init_clkdata(pdev, num_clks, &clk_data);
+	if (ret)
+		goto error_out;
+
+	/* level-1 gates */
+	ret = sg2042_clk_register_gates_fw(&pdev->dev, clk_data,
+					   sg2042_gate_clks_level_1,
+					   ARRAY_SIZE(sg2042_gate_clks_level_1));
+	if (ret)
+		goto error_out;
+
+	/* level-1 div */
+	ret = sg2042_clk_register_divs(&pdev->dev, clk_data, sg2042_div_clks_level_1,
+				       ARRAY_SIZE(sg2042_div_clks_level_1));
+	if (ret)
+		goto error_out;
+
+	/* mux */
+	ret = sg2042_clk_register_muxs(&pdev->dev, clk_data, sg2042_mux_clks,
+				       ARRAY_SIZE(sg2042_mux_clks));
+	if (ret)
+		goto error_out;
+
+	/* level 2 div */
+	ret = sg2042_clk_register_divs(&pdev->dev, clk_data, sg2042_div_clks_level_2,
+				       ARRAY_SIZE(sg2042_div_clks_level_2));
+	if (ret)
+		goto error_out;
+
+	/* level 2 gate */
+	ret = sg2042_clk_register_gates(&pdev->dev, clk_data, sg2042_gate_clks_level_2,
+					ARRAY_SIZE(sg2042_gate_clks_level_2));
+	if (ret)
+		goto error_out;
+
+	return devm_of_clk_add_hw_provider(&pdev->dev,
+					   of_clk_hw_onecell_get,
+					   &clk_data->onecell_data);
+
+error_out:
+	pr_err("%s failed error number %d\n", __func__, ret);
+	return ret;
+}
+
+static const struct of_device_id sg2042_clkgen_match[] = {
+	{ .compatible = "sophgo,sg2042-clkgen" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sg2042_clkgen_match);
+
+static struct platform_driver sg2042_clkgen_driver = {
+	.probe = sg2042_clkgen_probe,
+	.driver = {
+		.name = "clk-sophgo-sg2042-clkgen",
+		.of_match_table = sg2042_clkgen_match,
+		.suppress_bind_attrs = true,
+	},
+};
+module_platform_driver(sg2042_clkgen_driver);
+
+MODULE_AUTHOR("Chen Wang");
+MODULE_DESCRIPTION("Sophgo SG2042 clock generator driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/sophgo/clk-sg2042-pll.c b/drivers/clk/sophgo/clk-sg2042-pll.c
new file mode 100644
index 000000000000..aa142897aa5e
--- /dev/null
+++ b/drivers/clk/sophgo/clk-sg2042-pll.c
@@ -0,0 +1,570 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Sophgo SG2042 PLL clock Driver
+ *
+ * Copyright (C) 2024 Sophgo Technology Inc.
+ * Copyright (C) 2024 Chen Wang <unicorn_wang@xxxxxxxxxxx>
+ */
+
+#include <linux/array_size.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/platform_device.h>
+#include <asm/div64.h>
+
+#include <dt-bindings/clock/sophgo,sg2042-pll.h>
+
+#include "clk-sg2042.h"
+
+/* Registers defined in SYS_CTRL */
+#define R_PLL_BEGIN		0xC0
+#define R_PLL_STAT		(0xC0 - R_PLL_BEGIN)
+#define R_PLL_CLKEN_CONTROL	(0xC4 - R_PLL_BEGIN)
+#define R_MPLL_CONTROL		(0xE8 - R_PLL_BEGIN)
+#define R_FPLL_CONTROL		(0xF4 - R_PLL_BEGIN)
+#define R_DPLL0_CONTROL		(0xF8 - R_PLL_BEGIN)
+#define R_DPLL1_CONTROL		(0xFC - R_PLL_BEGIN)
+
+/**
+ * struct sg2042_pll_clock - PLL clock
+ * @hw:				clk_hw for initialization
+ * @id:				used to map clk_onecell_data
+ * @base:			used for readl/writel.
+ *				**NOTE**: PLL registers are all in SYS_CTRL!
+ * @lock:			spinlock to protect register access, modification
+ *				of frequency can only be served one at the time.
+ * @offset_ctrl:		offset of pll control registers
+ * @shift_status_lock:		shift of XXX_LOCK in pll status register
+ * @shift_status_updating:	shift of UPDATING_XXX in pll status register
+ * @shift_enable:		shift of XXX_CLK_EN in pll enable register
+ */
+struct sg2042_pll_clock {
+	struct clk_hw hw;
+
+	unsigned int id;
+	void __iomem *base;
+	/* protect register access */
+	spinlock_t *lock;
+
+	u32 offset_ctrl;
+	u8 shift_status_lock;
+	u8 shift_status_updating;
+	u8 shift_enable;
+};
+
+#define to_sg2042_pll_clk(_hw) container_of(_hw, struct sg2042_pll_clock, hw)
+
+#define KHZ 1000UL
+#define MHZ (KHZ * KHZ)
+
+#define REFDIV_MIN 1
+#define REFDIV_MAX 63
+#define FBDIV_MIN 16
+#define FBDIV_MAX 320
+
+#define PLL_FREF_SG2042 (25 * MHZ)
+
+#define PLL_FOUTPOSTDIV_MIN (16 * MHZ)
+#define PLL_FOUTPOSTDIV_MAX (3200 * MHZ)
+
+#define PLL_FOUTVCO_MIN (800 * MHZ)
+#define PLL_FOUTVCO_MAX (3200 * MHZ)
+
+struct sg2042_pll_ctrl {
+	unsigned long freq;
+	unsigned int fbdiv;
+	unsigned int postdiv1;
+	unsigned int postdiv2;
+	unsigned int refdiv;
+};
+
+#define PLLCTRL_FBDIV_MASK	GENMASK(27, 16)
+#define PLLCTRL_POSTDIV2_MASK	GENMASK(14, 12)
+#define PLLCTRL_POSTDIV1_MASK	GENMASK(10, 8)
+#define PLLCTRL_REFDIV_MASK	GENMASK(5, 0)
+
+static inline u32 sg2042_pll_ctrl_encode(struct sg2042_pll_ctrl *ctrl)
+{
+	return FIELD_PREP(PLLCTRL_FBDIV_MASK, ctrl->fbdiv) |
+	       FIELD_PREP(PLLCTRL_POSTDIV2_MASK, ctrl->postdiv2) |
+	       FIELD_PREP(PLLCTRL_POSTDIV1_MASK, ctrl->postdiv1) |
+	       FIELD_PREP(PLLCTRL_REFDIV_MASK, ctrl->refdiv);
+}
+
+static inline void sg2042_pll_ctrl_decode(unsigned int reg_value,
+					  struct sg2042_pll_ctrl *ctrl)
+{
+	ctrl->fbdiv = FIELD_GET(PLLCTRL_FBDIV_MASK, reg_value);
+	ctrl->refdiv = FIELD_GET(PLLCTRL_REFDIV_MASK, reg_value);
+	ctrl->postdiv1 = FIELD_GET(PLLCTRL_POSTDIV1_MASK, reg_value);
+	ctrl->postdiv2 = FIELD_GET(PLLCTRL_POSTDIV2_MASK, reg_value);
+}
+
+static inline int sg2042_pll_enable(struct sg2042_pll_clock *pll, bool en)
+{
+	u32 value;
+
+	if (en) {
+		/* wait pll lock */
+		if (readl_poll_timeout_atomic(pll->base + R_PLL_STAT,
+					      value,
+					      ((value >> pll->shift_status_lock) & 0x1),
+					      0,
+					      100000))
+			pr_warn("%s not locked\n", pll->hw.init->name);
+
+		/* wait pll updating */
+		if (readl_poll_timeout_atomic(pll->base + R_PLL_STAT,
+					      value,
+					      !((value >> pll->shift_status_updating) & 0x1),
+					      0,
+					      100000))
+			pr_warn("%s still updating\n", pll->hw.init->name);
+
+		/* enable pll */
+		value = readl(pll->base + R_PLL_CLKEN_CONTROL);
+		writel(value | (1 << pll->shift_enable), pll->base + R_PLL_CLKEN_CONTROL);
+	} else {
+		/* disable pll */
+		value = readl(pll->base + R_PLL_CLKEN_CONTROL);
+		writel(value & (~(1 << pll->shift_enable)), pll->base + R_PLL_CLKEN_CONTROL);
+	}
+
+	return 0;
+}
+
+/**
+ * sg2042_pll_recalc_rate() - Calculate rate for plls
+ * @reg_value: current register value
+ * @parent_rate: parent frequency
+ *
+ * This function is used to calculate below "rate" in equation
+ * rate = (parent_rate/REFDIV) x FBDIV/POSTDIV1/POSTDIV2
+ *      = (parent_rate x FBDIV) / (REFDIV x POSTDIV1 x POSTDIV2)
+ *
+ * Return: The rate calculated.
+ */
+static unsigned long sg2042_pll_recalc_rate(unsigned int reg_value,
+					    unsigned long parent_rate)
+{
+	struct sg2042_pll_ctrl ctrl_table;
+	u64 numerator, denominator;
+
+	sg2042_pll_ctrl_decode(reg_value, &ctrl_table);
+
+	numerator = parent_rate * ctrl_table.fbdiv;
+	denominator = ctrl_table.refdiv * ctrl_table.postdiv1 * ctrl_table.postdiv2;
+	do_div(numerator, denominator);
+	return numerator;
+}
+
+/**
+ * sg2042_pll_get_postdiv_1_2() - Based on input rate/prate/fbdiv/refdiv,
+ * look up the postdiv1_2 table to get the closest postdiiv combination.
+ * @rate: FOUTPOSTDIV
+ * @prate: parent rate, i.e. FREF
+ * @fbdiv: FBDIV
+ * @refdiv: REFDIV
+ * @postdiv1: POSTDIV1, output
+ * @postdiv2: POSTDIV2, output
+ *
+ * postdiv1_2 contains all the possible combination lists of POSTDIV1 and POSTDIV2
+ * for example:
+ * postdiv1_2[0] = {2, 4, 8}, where div1 = 2, div2 = 4 , div1 * div2 = 8
+ *
+ * See TRM:
+ * FOUTPOSTDIV = FREF * FBDIV / REFDIV / (POSTDIV1 * POSTDIV2)
+ * So we get following formula to get POSTDIV1 and POSTDIV2:
+ * POSTDIV = (prate/REFDIV) x FBDIV/rate
+ * above POSTDIV = POSTDIV1*POSTDIV2
+ *
+ * Return:
+ * %0 - OK
+ * %-EINVAL - invalid argument, which means Failed to get the postdivs.
+ */
+static int sg2042_pll_get_postdiv_1_2(unsigned long rate,
+				      unsigned long prate,
+				      unsigned int fbdiv,
+				      unsigned int refdiv,
+				      unsigned int *postdiv1,
+				      unsigned int *postdiv2)
+{
+	int index;
+	u64 tmp0;
+
+	/* POSTDIV_RESULT_INDEX point to 3rd element in the array postdiv1_2 */
+	#define	POSTDIV_RESULT_INDEX	2
+
+	static const int postdiv1_2[][3] = {
+		{2, 4,  8}, {3, 3,  9}, {2, 5, 10}, {2, 6, 12},
+		{2, 7, 14}, {3, 5, 15}, {4, 4, 16}, {3, 6, 18},
+		{4, 5, 20}, {3, 7, 21}, {4, 6, 24}, {5, 5, 25},
+		{4, 7, 28}, {5, 6, 30}, {5, 7, 35}, {6, 6, 36},
+		{6, 7, 42}, {7, 7, 49}
+	};
+
+	/* prate/REFDIV and result save to tmp0 */
+	tmp0 = prate;
+	do_div(tmp0, refdiv);
+
+	/* ((prate/REFDIV) x FBDIV) and result save to tmp0 */
+	tmp0 *= fbdiv;
+
+	/* ((prate/REFDIV) x FBDIV)/rate and result save to tmp0 */
+	do_div(tmp0, rate);
+
+	/* tmp0 is POSTDIV1*POSTDIV2, now we calculate div1 and div2 value */
+	if (tmp0 <= 7) {
+		/* (div1 * div2) <= 7, no need to use array search */
+		*postdiv1 = tmp0;
+		*postdiv2 = 1;
+		return 0;
+	}
+
+	/* (div1 * div2) > 7, use array search */
+	for (index = 0; index < ARRAY_SIZE(postdiv1_2); index++) {
+		if (tmp0 > postdiv1_2[index][POSTDIV_RESULT_INDEX]) {
+			continue;
+		} else {
+			/* found it */
+			*postdiv1 = postdiv1_2[index][1];
+			*postdiv2 = postdiv1_2[index][0];
+			return 0;
+		}
+	}
+	pr_warn("%s can not find in postdiv array!\n", __func__);
+	return -EINVAL;
+}
+
+/**
+ * sg2042_get_pll_ctl_setting() - Based on the given FOUTPISTDIV and the input
+ * FREF to calculate the REFDIV/FBDIV/PSTDIV1/POSTDIV2 combination for pllctrl
+ * register.
+ * @req_rate: expected output clock rate, i.e. FOUTPISTDIV
+ * @parent_rate: input parent clock rate, i.e. FREF
+ * @best: output to hold calculated combination of REFDIV/FBDIV/PSTDIV1/POSTDIV2
+ *
+ * Return:
+ * %0 - OK
+ * %-EINVAL - invalid argument
+ */
+static int sg2042_get_pll_ctl_setting(struct sg2042_pll_ctrl *best,
+				      unsigned long req_rate,
+				      unsigned long parent_rate)
+{
+	unsigned int fbdiv, refdiv, postdiv1, postdiv2;
+	unsigned long foutpostdiv;
+	u64 foutvco;
+	int ret;
+	u64 tmp;
+
+	if (parent_rate != PLL_FREF_SG2042) {
+		pr_err("INVALID FREF: %ld\n", parent_rate);
+		return -EINVAL;
+	}
+
+	if (req_rate < PLL_FOUTPOSTDIV_MIN || req_rate > PLL_FOUTPOSTDIV_MAX) {
+		pr_alert("INVALID FOUTPOSTDIV: %ld\n", req_rate);
+		return -EINVAL;
+	}
+
+	memset(best, 0, sizeof(struct sg2042_pll_ctrl));
+
+	for (refdiv = REFDIV_MIN; refdiv < REFDIV_MAX + 1; refdiv++) {
+		/* required by hardware: FREF/REFDIV must > 10 */
+		tmp = parent_rate;
+		do_div(tmp, refdiv);
+		if (tmp <= 10)
+			continue;
+
+		for (fbdiv = FBDIV_MIN; fbdiv < FBDIV_MAX + 1; fbdiv++) {
+			/*
+			 * FOUTVCO = FREF*FBDIV/REFDIV validation
+			 * required by hardware, FOUTVCO must [800MHz, 3200MHz]
+			 */
+			foutvco = parent_rate * fbdiv;
+			do_div(foutvco, refdiv);
+			if (foutvco < PLL_FOUTVCO_MIN || foutvco > PLL_FOUTVCO_MAX)
+				continue;
+
+			ret = sg2042_pll_get_postdiv_1_2(req_rate, parent_rate,
+							 fbdiv, refdiv,
+							 &postdiv1, &postdiv2);
+			if (ret)
+				continue;
+
+			/*
+			 * FOUTPOSTDIV = FREF*FBDIV/REFDIV/(POSTDIV1*POSTDIV2)
+			 *             = FOUTVCO/(POSTDIV1*POSTDIV2)
+			 */
+			tmp = foutvco;
+			do_div(tmp, (postdiv1 * postdiv2));
+			foutpostdiv = (unsigned long)tmp;
+			/* Iterative to approach the expected value */
+			if (abs_diff(foutpostdiv, req_rate) < abs_diff(best->freq, req_rate)) {
+				best->freq = foutpostdiv;
+				best->refdiv = refdiv;
+				best->fbdiv = fbdiv;
+				best->postdiv1 = postdiv1;
+				best->postdiv2 = postdiv2;
+				if (foutpostdiv == req_rate)
+					return 0;
+			}
+			continue;
+		}
+	}
+
+	if (best->freq == 0)
+		return -EINVAL;
+	else
+		return 0;
+}
+
+/**
+ * sg2042_clk_pll_recalc_rate() - recalc_rate callback for pll clks
+ * @hw: ccf use to hook get sg2042_pll_clock
+ * @parent_rate: parent rate
+ *
+ * The is function will be called through clk_get_rate
+ * and return current rate after decoding reg value
+ *
+ * Return: Current rate recalculated.
+ */
+static unsigned long sg2042_clk_pll_recalc_rate(struct clk_hw *hw,
+						unsigned long parent_rate)
+{
+	struct sg2042_pll_clock *pll = to_sg2042_pll_clk(hw);
+	unsigned long rate;
+	u32 value;
+
+	value = readl(pll->base + pll->offset_ctrl);
+	rate = sg2042_pll_recalc_rate(value, parent_rate);
+
+	pr_debug("--> %s: pll_recalc_rate: val = %ld\n",
+		 clk_hw_get_name(hw), rate);
+	return rate;
+}
+
+static long sg2042_clk_pll_round_rate(struct clk_hw *hw,
+				      unsigned long req_rate,
+				      unsigned long *prate)
+{
+	struct sg2042_pll_ctrl pctrl_table;
+	unsigned int value;
+	long proper_rate;
+	int ret;
+
+	ret = sg2042_get_pll_ctl_setting(&pctrl_table, req_rate, *prate);
+	if (ret) {
+		proper_rate = 0;
+		goto out;
+	}
+
+	value = sg2042_pll_ctrl_encode(&pctrl_table);
+	proper_rate = (long)sg2042_pll_recalc_rate(value, *prate);
+
+out:
+	pr_debug("--> %s: pll_round_rate: val = %ld\n",
+		 clk_hw_get_name(hw), proper_rate);
+	return proper_rate;
+}
+
+static int sg2042_clk_pll_determine_rate(struct clk_hw *hw,
+					 struct clk_rate_request *req)
+{
+	req->rate = sg2042_clk_pll_round_rate(hw, min(req->rate, req->max_rate),
+					      &req->best_parent_rate);
+	pr_debug("--> %s: pll_determine_rate: val = %ld\n",
+		 clk_hw_get_name(hw), req->rate);
+	return 0;
+}
+
+static int sg2042_clk_pll_set_rate(struct clk_hw *hw,
+				   unsigned long rate,
+				   unsigned long parent_rate)
+{
+	struct sg2042_pll_clock *pll = to_sg2042_pll_clk(hw);
+	struct sg2042_pll_ctrl pctrl_table;
+	unsigned long flags;
+	u32 value;
+	int ret;
+
+	spin_lock_irqsave(pll->lock, flags);
+	if (sg2042_pll_enable(pll, 0)) {
+		pr_warn("Can't disable pll(%s), status error\n", pll->hw.init->name);
+		goto out;
+	}
+	ret = sg2042_get_pll_ctl_setting(&pctrl_table, rate, parent_rate);
+	if (ret) {
+		pr_warn("%s: Can't find a proper pll setting\n", pll->hw.init->name);
+		goto out2;
+	}
+
+	value = sg2042_pll_ctrl_encode(&pctrl_table);
+
+	/* write the value to top register */
+	writel(value, pll->base + pll->offset_ctrl);
+
+out2:
+	sg2042_pll_enable(pll, 1);
+out:
+	spin_unlock_irqrestore(pll->lock, flags);
+
+	pr_debug("--> %s: pll_set_rate: val = 0x%x\n",
+		 clk_hw_get_name(hw), value);
+	return ret;
+}
+
+static const struct clk_ops sg2042_clk_pll_ops = {
+	.recalc_rate = sg2042_clk_pll_recalc_rate,
+	.round_rate = sg2042_clk_pll_round_rate,
+	.determine_rate = sg2042_clk_pll_determine_rate,
+	.set_rate = sg2042_clk_pll_set_rate,
+};
+
+static const struct clk_ops sg2042_clk_pll_ro_ops = {
+	.recalc_rate = sg2042_clk_pll_recalc_rate,
+	.round_rate = sg2042_clk_pll_round_rate,
+};
+
+/*
+ * Clock initialization macro naming rules:
+ * FW: use CLK_HW_INIT_FW_NAME
+ * RO: means Read-Only
+ */
+#define SG2042_PLL_FW(_id, _name, _parent, _r_ctrl, _shift)		\
+	{								\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_FW_NAME(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_pll_ops,			\
+				CLK_GET_RATE_NOCACHE | CLK_GET_ACCURACY_NOCACHE),\
+		.offset_ctrl = _r_ctrl,					\
+		.shift_status_lock = 8 + (_shift),			\
+		.shift_status_updating = _shift,			\
+		.shift_enable = _shift,					\
+	}
+
+#define SG2042_PLL_FW_RO(_id, _name, _parent, _r_ctrl, _shift)		\
+	{								\
+		.id = _id,						\
+		.hw.init = CLK_HW_INIT_FW_NAME(				\
+				_name,					\
+				_parent,				\
+				&sg2042_clk_pll_ro_ops,			\
+				CLK_GET_RATE_NOCACHE | CLK_GET_ACCURACY_NOCACHE),\
+		.offset_ctrl = _r_ctrl,					\
+		.shift_status_lock = 8 + (_shift),			\
+		.shift_status_updating = _shift,			\
+		.shift_enable = _shift,					\
+	}
+
+static struct sg2042_pll_clock sg2042_pll_clks[] = {
+	SG2042_PLL_FW(MPLL_CLK, "mpll_clock", "cgi_main", R_MPLL_CONTROL, 0),
+	SG2042_PLL_FW_RO(FPLL_CLK, "fpll_clock", "cgi_main", R_FPLL_CONTROL, 3),
+	SG2042_PLL_FW_RO(DPLL0_CLK, "dpll0_clock", "cgi_dpll0", R_DPLL0_CONTROL, 4),
+	SG2042_PLL_FW_RO(DPLL1_CLK, "dpll1_clock", "cgi_dpll1", R_DPLL1_CONTROL, 5),
+};
+
+static DEFINE_SPINLOCK(sg2042_clk_lock);
+
+static int sg2042_clk_register_plls(struct device *dev,
+				    struct sg2042_clk_data *clk_data,
+				    struct sg2042_pll_clock pll_clks[],
+				    int num_pll_clks)
+{
+	struct sg2042_pll_clock *pll;
+	struct clk_hw *hw;
+	int i, ret = 0;
+
+	for (i = 0; i < num_pll_clks; i++) {
+		pll = &pll_clks[i];
+		/* assign these for ops usage during registration */
+		pll->base = clk_data->iobase;
+		pll->lock = &sg2042_clk_lock;
+
+		hw = &pll->hw;
+		ret = devm_clk_hw_register(dev, hw);
+		if (ret) {
+			pr_err("failed to register clock %s\n", pll->hw.init->name);
+			break;
+		}
+
+		clk_data->onecell_data.hws[pll->id] = hw;
+	}
+
+	return ret;
+}
+
+static int sg2042_init_clkdata(struct platform_device *pdev,
+			       int num_clks,
+			       struct sg2042_clk_data **pp_clk_data)
+{
+	struct sg2042_clk_data *clk_data;
+
+	clk_data = devm_kzalloc(&pdev->dev,
+				struct_size(clk_data, onecell_data.hws, num_clks),
+				GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->iobase = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(clk_data->iobase)))
+		return PTR_ERR(clk_data->iobase);
+
+	clk_data->onecell_data.num = num_clks;
+
+	*pp_clk_data = clk_data;
+
+	return 0;
+}
+
+static int sg2042_pll_probe(struct platform_device *pdev)
+{
+	struct sg2042_clk_data *clk_data = NULL;
+	int num_clks;
+	int ret;
+
+	num_clks = ARRAY_SIZE(sg2042_pll_clks);
+
+	ret = sg2042_init_clkdata(pdev, num_clks, &clk_data);
+	if (ret)
+		goto error_out;
+
+	ret = sg2042_clk_register_plls(&pdev->dev, clk_data, sg2042_pll_clks,
+				       num_clks);
+	if (ret)
+		goto error_out;
+
+	return devm_of_clk_add_hw_provider(&pdev->dev,
+					   of_clk_hw_onecell_get,
+					   &clk_data->onecell_data);
+
+error_out:
+	pr_err("%s failed error number %d\n", __func__, ret);
+	return ret;
+}
+
+static const struct of_device_id sg2042_pll_match[] = {
+	{ .compatible = "sophgo,sg2042-pll" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sg2042_pll_match);
+
+static struct platform_driver sg2042_pll_driver = {
+	.probe = sg2042_pll_probe,
+	.driver = {
+		.name = "clk-sophgo-sg2042-pll",
+		.of_match_table = sg2042_pll_match,
+		.suppress_bind_attrs = true,
+	},
+};
+module_platform_driver(sg2042_pll_driver);
+
+MODULE_AUTHOR("Chen Wang");
+MODULE_DESCRIPTION("Sophgo SG2042 pll clock driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/sophgo/clk-sg2042-rpgate.c b/drivers/clk/sophgo/clk-sg2042-rpgate.c
new file mode 100644
index 000000000000..5b38d4f15525
--- /dev/null
+++ b/drivers/clk/sophgo/clk-sg2042-rpgate.c
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Sophgo SG2042 RP clock Driver
+ *
+ * Copyright (C) 2024 Sophgo Technology Inc.
+ * Copyright (C) 2024 Chen Wang <unicorn_wang@xxxxxxxxxxx>
+ */
+
+#include <linux/array_size.h>
+#include <linux/clk-provider.h>
+#include <linux/platform_device.h>
+
+#include <dt-bindings/clock/sophgo,sg2042-rpgate.h>
+
+#include "clk-sg2042.h"
+
+#define R_SYSGATE_BEGIN		0x0368
+#define R_RP_RXU_CLK_ENABLE	(0x0368 - R_SYSGATE_BEGIN)
+#define R_MP0_STATUS_REG	(0x0380 - R_SYSGATE_BEGIN)
+#define R_MP0_CONTROL_REG	(0x0384 - R_SYSGATE_BEGIN)
+#define R_MP1_STATUS_REG	(0x0388 - R_SYSGATE_BEGIN)
+#define R_MP1_CONTROL_REG	(0x038C - R_SYSGATE_BEGIN)
+#define R_MP2_STATUS_REG	(0x0390 - R_SYSGATE_BEGIN)
+#define R_MP2_CONTROL_REG	(0x0394 - R_SYSGATE_BEGIN)
+#define R_MP3_STATUS_REG	(0x0398 - R_SYSGATE_BEGIN)
+#define R_MP3_CONTROL_REG	(0x039C - R_SYSGATE_BEGIN)
+#define R_MP4_STATUS_REG	(0x03A0 - R_SYSGATE_BEGIN)
+#define R_MP4_CONTROL_REG	(0x03A4 - R_SYSGATE_BEGIN)
+#define R_MP5_STATUS_REG	(0x03A8 - R_SYSGATE_BEGIN)
+#define R_MP5_CONTROL_REG	(0x03AC - R_SYSGATE_BEGIN)
+#define R_MP6_STATUS_REG	(0x03B0 - R_SYSGATE_BEGIN)
+#define R_MP6_CONTROL_REG	(0x03B4 - R_SYSGATE_BEGIN)
+#define R_MP7_STATUS_REG	(0x03B8 - R_SYSGATE_BEGIN)
+#define R_MP7_CONTROL_REG	(0x03BC - R_SYSGATE_BEGIN)
+#define R_MP8_STATUS_REG	(0x03C0 - R_SYSGATE_BEGIN)
+#define R_MP8_CONTROL_REG	(0x03C4 - R_SYSGATE_BEGIN)
+#define R_MP9_STATUS_REG	(0x03C8 - R_SYSGATE_BEGIN)
+#define R_MP9_CONTROL_REG	(0x03CC - R_SYSGATE_BEGIN)
+#define R_MP10_STATUS_REG	(0x03D0 - R_SYSGATE_BEGIN)
+#define R_MP10_CONTROL_REG	(0x03D4 - R_SYSGATE_BEGIN)
+#define R_MP11_STATUS_REG	(0x03D8 - R_SYSGATE_BEGIN)
+#define R_MP11_CONTROL_REG	(0x03DC - R_SYSGATE_BEGIN)
+#define R_MP12_STATUS_REG	(0x03E0 - R_SYSGATE_BEGIN)
+#define R_MP12_CONTROL_REG	(0x03E4 - R_SYSGATE_BEGIN)
+#define R_MP13_STATUS_REG	(0x03E8 - R_SYSGATE_BEGIN)
+#define R_MP13_CONTROL_REG	(0x03EC - R_SYSGATE_BEGIN)
+#define R_MP14_STATUS_REG	(0x03F0 - R_SYSGATE_BEGIN)
+#define R_MP14_CONTROL_REG	(0x03F4 - R_SYSGATE_BEGIN)
+#define R_MP15_STATUS_REG	(0x03F8 - R_SYSGATE_BEGIN)
+#define R_MP15_CONTROL_REG	(0x03FC - R_SYSGATE_BEGIN)
+
+/**
+ * struct sg2042_rpgate_clock - Gate clock for RP(riscv processors) subsystem
+ * @hw:			clk_hw for initialization
+ * @id:			used to map clk_onecell_data
+ * @offset_enable:	offset of gate enable registers
+ * @bit_idx:		which bit in the register controls gating of this clock
+ */
+struct sg2042_rpgate_clock {
+	struct clk_hw hw;
+
+	unsigned int id;
+
+	u32 offset_enable;
+	u8 bit_idx;
+};
+
+/*
+ * Clock initialization macro naming rules:
+ * FW: use CLK_HW_INIT_FW_NAME
+ */
+#define SG2042_GATE_FW(_id, _name, _parent, _flags,	\
+		       _r_enable, _bit_idx) {		\
+		.hw.init = CLK_HW_INIT_FW_NAME(		\
+				_name,			\
+				_parent,		\
+				NULL,			\
+				_flags),		\
+		.id = _id,				\
+		.offset_enable = _r_enable,		\
+		.bit_idx = _bit_idx,			\
+	}
+
+/*
+ * Gate clocks for RP subsystem (including the MP subsystem), which control
+ * registers are defined in SYS_CTRL.
+ */
+static const struct sg2042_rpgate_clock sg2042_gate_rp[] = {
+	/* downstream of clk_gate_rp_cpu_normal about rxu */
+	SG2042_GATE_FW(GATE_CLK_RXU0, "clk_gate_rxu0", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 0),
+	SG2042_GATE_FW(GATE_CLK_RXU1, "clk_gate_rxu1", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 1),
+	SG2042_GATE_FW(GATE_CLK_RXU2, "clk_gate_rxu2", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 2),
+	SG2042_GATE_FW(GATE_CLK_RXU3, "clk_gate_rxu3", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 3),
+	SG2042_GATE_FW(GATE_CLK_RXU4, "clk_gate_rxu4", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 4),
+	SG2042_GATE_FW(GATE_CLK_RXU5, "clk_gate_rxu5", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 5),
+	SG2042_GATE_FW(GATE_CLK_RXU6, "clk_gate_rxu6", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 6),
+	SG2042_GATE_FW(GATE_CLK_RXU7, "clk_gate_rxu7", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 7),
+	SG2042_GATE_FW(GATE_CLK_RXU8, "clk_gate_rxu8", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 8),
+	SG2042_GATE_FW(GATE_CLK_RXU9, "clk_gate_rxu9", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 9),
+	SG2042_GATE_FW(GATE_CLK_RXU10, "clk_gate_rxu10", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 10),
+	SG2042_GATE_FW(GATE_CLK_RXU11, "clk_gate_rxu11", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 11),
+	SG2042_GATE_FW(GATE_CLK_RXU12, "clk_gate_rxu12", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 12),
+	SG2042_GATE_FW(GATE_CLK_RXU13, "clk_gate_rxu13", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 13),
+	SG2042_GATE_FW(GATE_CLK_RXU14, "clk_gate_rxu14", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 14),
+	SG2042_GATE_FW(GATE_CLK_RXU15, "clk_gate_rxu15", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 15),
+	SG2042_GATE_FW(GATE_CLK_RXU16, "clk_gate_rxu16", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 16),
+	SG2042_GATE_FW(GATE_CLK_RXU17, "clk_gate_rxu17", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 17),
+	SG2042_GATE_FW(GATE_CLK_RXU18, "clk_gate_rxu18", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 18),
+	SG2042_GATE_FW(GATE_CLK_RXU19, "clk_gate_rxu19", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 19),
+	SG2042_GATE_FW(GATE_CLK_RXU20, "clk_gate_rxu20", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 20),
+	SG2042_GATE_FW(GATE_CLK_RXU21, "clk_gate_rxu21", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 21),
+	SG2042_GATE_FW(GATE_CLK_RXU22, "clk_gate_rxu22", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 22),
+	SG2042_GATE_FW(GATE_CLK_RXU23, "clk_gate_rxu23", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 23),
+	SG2042_GATE_FW(GATE_CLK_RXU24, "clk_gate_rxu24", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 24),
+	SG2042_GATE_FW(GATE_CLK_RXU25, "clk_gate_rxu25", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 25),
+	SG2042_GATE_FW(GATE_CLK_RXU26, "clk_gate_rxu26", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 26),
+	SG2042_GATE_FW(GATE_CLK_RXU27, "clk_gate_rxu27", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 27),
+	SG2042_GATE_FW(GATE_CLK_RXU28, "clk_gate_rxu28", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 28),
+	SG2042_GATE_FW(GATE_CLK_RXU29, "clk_gate_rxu29", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 29),
+	SG2042_GATE_FW(GATE_CLK_RXU30, "clk_gate_rxu30", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 30),
+	SG2042_GATE_FW(GATE_CLK_RXU31, "clk_gate_rxu31", "rpgate",
+		       0, R_RP_RXU_CLK_ENABLE, 31),
+
+	/* downstream of clk_gate_rp_cpu_normal about mp */
+	SG2042_GATE_FW(GATE_CLK_MP0, "clk_gate_mp0", "rpgate",
+		       CLK_IS_CRITICAL, R_MP0_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP1, "clk_gate_mp1", "rpgate",
+		       CLK_IS_CRITICAL, R_MP1_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP2, "clk_gate_mp2", "rpgate",
+		       CLK_IS_CRITICAL, R_MP2_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP3, "clk_gate_mp3", "rpgate",
+		       CLK_IS_CRITICAL, R_MP3_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP4, "clk_gate_mp4", "rpgate",
+		       CLK_IS_CRITICAL, R_MP4_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP5, "clk_gate_mp5", "rpgate",
+		       CLK_IS_CRITICAL, R_MP5_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP6, "clk_gate_mp6", "rpgate",
+		       CLK_IS_CRITICAL, R_MP6_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP7, "clk_gate_mp7", "rpgate",
+		       CLK_IS_CRITICAL, R_MP7_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP8, "clk_gate_mp8", "rpgate",
+		       CLK_IS_CRITICAL, R_MP8_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP9, "clk_gate_mp9", "rpgate",
+		       CLK_IS_CRITICAL, R_MP9_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP10, "clk_gate_mp10", "rpgate",
+		       CLK_IS_CRITICAL, R_MP10_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP11, "clk_gate_mp11", "rpgate",
+		       CLK_IS_CRITICAL, R_MP11_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP12, "clk_gate_mp12", "rpgate",
+		       CLK_IS_CRITICAL, R_MP12_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP13, "clk_gate_mp13", "rpgate",
+		       CLK_IS_CRITICAL, R_MP13_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP14, "clk_gate_mp14", "rpgate",
+		       CLK_IS_CRITICAL, R_MP14_CONTROL_REG, 0),
+	SG2042_GATE_FW(GATE_CLK_MP15, "clk_gate_mp15", "rpgate",
+		       CLK_IS_CRITICAL, R_MP15_CONTROL_REG, 0),
+};
+
+static DEFINE_SPINLOCK(sg2042_clk_lock);
+
+static int sg2042_clk_register_rpgates(struct device *dev,
+				       struct sg2042_clk_data *clk_data,
+				       const struct sg2042_rpgate_clock gate_clks[],
+				       int num_gate_clks)
+{
+	const struct sg2042_rpgate_clock *gate;
+	struct clk_hw *hw;
+	int i, ret = 0;
+
+	for (i = 0; i < num_gate_clks; i++) {
+		gate = &gate_clks[i];
+		hw = devm_clk_hw_register_gate_parent_data
+			(dev,
+			 gate->hw.init->name,
+			 gate->hw.init->parent_data,
+			 gate->hw.init->flags,
+			 clk_data->iobase + gate->offset_enable,
+			 gate->bit_idx,
+			 0,
+			 &sg2042_clk_lock);
+		if (IS_ERR(hw)) {
+			pr_err("failed to register clock %s\n", gate->hw.init->name);
+			ret = PTR_ERR(hw);
+			break;
+		}
+
+		clk_data->onecell_data.hws[gate->id] = hw;
+	}
+
+	return ret;
+}
+
+static int sg2042_init_clkdata(struct platform_device *pdev,
+			       int num_clks,
+			       struct sg2042_clk_data **pp_clk_data)
+{
+	struct sg2042_clk_data *clk_data;
+
+	clk_data = devm_kzalloc(&pdev->dev,
+				struct_size(clk_data, onecell_data.hws, num_clks),
+				GFP_KERNEL);
+	if (!clk_data)
+		return -ENOMEM;
+
+	clk_data->iobase = devm_platform_ioremap_resource(pdev, 0);
+	if (WARN_ON(IS_ERR(clk_data->iobase)))
+		return PTR_ERR(clk_data->iobase);
+
+	clk_data->onecell_data.num = num_clks;
+
+	*pp_clk_data = clk_data;
+
+	return 0;
+}
+
+static int sg2042_rpgate_probe(struct platform_device *pdev)
+{
+	struct sg2042_clk_data *clk_data = NULL;
+	int num_clks;
+	int ret;
+
+	num_clks = ARRAY_SIZE(sg2042_gate_rp);
+
+	ret = sg2042_init_clkdata(pdev, num_clks, &clk_data);
+	if (ret)
+		goto error_out;
+
+	ret = sg2042_clk_register_rpgates(&pdev->dev, clk_data, sg2042_gate_rp,
+					  num_clks);
+	if (ret)
+		goto error_out;
+
+	return devm_of_clk_add_hw_provider(&pdev->dev,
+					   of_clk_hw_onecell_get,
+					   &clk_data->onecell_data);
+
+error_out:
+	pr_err("%s failed error number %d\n", __func__, ret);
+	return ret;
+}
+
+static const struct of_device_id sg2042_rpgate_match[] = {
+	{ .compatible = "sophgo,sg2042-rpgate" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sg2042_rpgate_match);
+
+static struct platform_driver sg2042_rpgate_driver = {
+	.probe = sg2042_rpgate_probe,
+	.driver = {
+		.name = "clk-sophgo-sg2042-rpgate",
+		.of_match_table = sg2042_rpgate_match,
+		.suppress_bind_attrs = true,
+	},
+};
+module_platform_driver(sg2042_rpgate_driver);
+
+MODULE_AUTHOR("Chen Wang");
+MODULE_DESCRIPTION("Sophgo SG2042 rp subsystem clock driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/sophgo/clk-sg2042.h b/drivers/clk/sophgo/clk-sg2042.h
new file mode 100644
index 000000000000..f13fed399c6e
--- /dev/null
+++ b/drivers/clk/sophgo/clk-sg2042.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _CLK_SOPHGO_SG2042_H_
+#define _CLK_SOPHGO_SG2042_H_
+
+#include <linux/io.h>
+#include <linux/clk-provider.h>
+
+/**
+ * struct sg2042_clk_data - Common data of clock-controller
+ * @iobase: base address of clock-controller
+ * @onecell_data: used for adding providers.
+ */
+struct sg2042_clk_data {
+	void __iomem *iobase;
+	struct clk_hw_onecell_data onecell_data;
+};
+
+#endif /* _CLK_SOPHGO_SG2042_H_ */
-- 
2.25.1





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux