From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
Add a node for the PMU module of the QCA6391 present on the RB5 board.
Assign its LDO power outputs to the existing Bluetooth module. Add a
node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
the board's .dts and also make it consume the power outputs of the PMU.
Tested-by: Caleb Connolly <caleb.connolly@xxxxxxxxxx> # OnePlus 8T
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 103 ++++++++++++++++++++---
arch/arm64/boot/dts/qcom/sm8250.dtsi | 2 +-
2 files changed, 93 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index c52357214de5..daf830dfe4b5 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -108,6 +108,67 @@ lt9611_3v3: lt9611-3v3 {
regulator-always-on;
};
+ qca6390-pmu {
+ compatible = "qcom,qca6390-pmu";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
+
+ vddaon-supply = <&vreg_s6a_0p95>;
+ vddpmu-supply = <&vreg_s2f_0p95>;
+ vddrfa0p95-supply = <&vreg_s2f_0p95>;
+ vddrfa1p3-supply = <&vreg_s8c_1p3>;
+ vddrfa1p9-supply = <&vreg_s5a_1p9>;
+ vddpcie1p3-supply = <&vreg_s8c_1p3>;
+ vddpcie1p9-supply = <&vreg_s5a_1p9>;
+ vddio-supply = <&vreg_s4a_1p8>;
+
+ wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
+
thermal-zones {
conn-thermal {
polling-delay-passive = <0>;
@@ -734,6 +795,23 @@ &pcie0_phy {
vdda-pll-supply = <&vreg_l9a_1p2>;
};
+&pcieport0 {
+ wifi@0 {
+ compatible = "pci17cb,1101";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
&pcie1 {
status = "okay";
};
@@ -1303,6 +1381,14 @@ sdc2_card_det_n: sd-card-det-n-state {
function = "gpio";
bias-pull-up;
};
+
+ wlan_en_state: wlan-default-state {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <16>;
+ output-low;
+ bias-pull-up;
+ };
};
&uart6 {
@@ -1311,17 +1397,12 @@ &uart6 {
bluetooth {
compatible = "qcom,qca6390-bt";
- pinctrl-names = "default";
- pinctrl-0 = <&bt_en_state>;
-
- enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
-
- vddio-supply = <&vreg_s4a_1p8>;
- vddpmu-supply = <&vreg_s2f_0p95>;
- vddaon-supply = <&vreg_s6a_0p95>;
- vddrfa0p9-supply = <&vreg_s2f_0p95>;
- vddrfa1p3-supply = <&vreg_s8c_1p3>;
- vddrfa1p9-supply = <&vreg_s5a_1p9>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index f3f9dea0550b..95471ba46f9d 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -2204,7 +2204,7 @@ pcie0: pcie@1c00000 {
status = "disabled";
- pcie@0 {
+ pcieport0: pcie@0 {
device_type = "pci";
reg = <0x0 0x0 0x0 0x0 0x0>;
bus-range = <0x01 0xff>;
--
2.40.1
