On Tue, May 28, 2024 at 11:22:18PM +0300, Laurent Pinchart wrote:
> On Tue, May 28, 2024 at 11:20:45PM +0300, Laurent Pinchart wrote:
> > Hi Andy,
> >
> > Thank you for the patch.
I meant for the review. It's getting late.
> > On Tue, May 28, 2024 at 10:36:06PM +0300, Andy Shevchenko wrote:
> > > Tue, May 28, 2024 at 10:03:13PM +0300, Laurent Pinchart kirjoitti:
> > > > From: Haibo Chen <haibo.chen@xxxxxxx>
> > > >
> > > > The ADP5585 is a 10/11 input/output port expander with a built in keypad
> > > > matrix decoder, programmable logic, reset generator, and PWM generator.
> > > > This driver supports the GPIO function using the platform device
> > > > registered by the core MFD driver.
> > > >
> > > > The driver is derived from an initial implementation from NXP, available
> > > > in commit 451f61b46b76 ("MLK-25917-2 gpio: adp5585-gpio: add
> > > > adp5585-gpio support") in their BSP kernel tree. It has been extensively
> > > > rewritten.
> > >
> > > Why is this not using gpio-regmap?
>
> I forgot to answer this:
>
> I don't think it's a good match for the hardware.
>
> > > ...
> > >
> > > > +#include <linux/device.h>
> > > > +#include <linux/gpio/driver.h>
> > > > +#include <linux/mfd/adp5585.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/platform_device.h>
> > > > +#include <linux/regmap.h>
> > >
> > > + types.h
> > >
> > > ...
> > >
> > > > + bit = off * 2 + (off > 5 ? 4 : 0);
> > >
> > > Right, but can you use >= 6 here which immediately follows to the next
> > > question, i.e. why not use bank in this conditional?
> >
> > The ADP5585_BANK() macro is meant to be used with ADP5585_BIT(), for a
> > set of registers with the same layout. Here the layout is different, the
> > registers contain multi-bit fields. I can't use ADP5585_BIT(), so I'd
> > rather not use ADP5585_BANK() either. I have decided to use > 5 instead
> > of >= 6 to match the R5 field name in the comment above:
> >
> > /*
> > * The bias configuration fields are 2 bits wide and laid down in
> > * consecutive registers ADP5585_RPULL_CONFIG_*, with a hole of 4 bits
> > * after R5.
> > */
> >
> > > ...
> > >
> > > > + struct adp5585_dev *adp5585 = dev_get_drvdata(pdev->dev.parent);
> > >
> > > (see below)
> > >
> > > > + struct adp5585_gpio_dev *adp5585_gpio;
> > > > + struct device *dev = &pdev->dev;
> > >
> > > struct adp5585_dev *adp5585 = dev_get_drvdata(dev->parent);
> >
> > I prefer keeping the current ordering, with long lines first, I think
> > that's more readable.
> >
> > > > + struct gpio_chip *gc;
> > > > + int ret;
> > >
> > > ...
> > >
> > > > + platform_set_drvdata(pdev, adp5585_gpio);
> > >
> > > Any use of driver data?
> >
> > In v1, not v2. I'll drop it.
> >
> > > ...
> > >
> > > > + device_set_of_node_from_dev(dev, dev->parent);
> > >
> > > Why not device_set_node()?
> >
> > Because device_set_of_node_from_dev() is meant for this exact use case,
> > where the same node is used for multiple devices. It also puts any
> > previous dev->of_node, ensuring proper refcounting when devices are
> > unbound and rebound, without being deleted.
> >
> > --
> > Regards,
> >
> > Laurent Pinchart
>
> --
> Regards,
>
> Laurent Pinchart
--
Regards,
Laurent Pinchart
