[PATCH v6 2/2] phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add i.MX8QM HSIO PHY driver support.

i.MX8QM HSIO has three lane PHY instances, and can be bound to the
following controllers in the different use cases listed in below table.
- two lanes capable PCIEA controller.
- one lane PCIEB controller.
- AHCI SATA controller.

i.MX8QM HSIO PHYs support the following use cases.
+----------------------------------------------------+
|                               | Lane0| Lane1| Lane2|
|-------------------------------|------|------|------|
| use case 1: PCIEAX2SATA       | PCIEA| PCIEA| SATA |
|-------------------------------|------|------|------|
| use case 2: PCIEAX2PCIEB      | PCIEA| PCIEA| PCIEB|
|-------------------------------|------|------|------|
| use case 3: PCIEAPCIEBSATA    | PCIEA| PCIEB| SATA |
+----------------------------------------------------+

Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
---
 drivers/phy/freescale/Kconfig               |   8 +
 drivers/phy/freescale/Makefile              |   1 +
 drivers/phy/freescale/phy-fsl-imx8qm-hsio.c | 612 ++++++++++++++++++++
 3 files changed, 621 insertions(+)
 create mode 100644 drivers/phy/freescale/phy-fsl-imx8qm-hsio.c

diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
index 853958fb2c06..c9ee48aeea9e 100644
--- a/drivers/phy/freescale/Kconfig
+++ b/drivers/phy/freescale/Kconfig
@@ -35,6 +35,14 @@ config PHY_FSL_IMX8M_PCIE
 	  Enable this to add support for the PCIE PHY as found on
 	  i.MX8M family of SOCs.
 
+config PHY_FSL_IMX8QM_HSIO
+	tristate "Freescale i.MX8QM HSIO PHY"
+	depends on OF && HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to add support for the HSIO PHY as found on
+	  i.MX8QM family of SOCs.
+
 endif
 
 config PHY_FSL_LYNX_28G
diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
index cedb328bc4d2..b56b4d5c18ea 100644
--- a/drivers/phy/freescale/Makefile
+++ b/drivers/phy/freescale/Makefile
@@ -3,4 +3,5 @@ obj-$(CONFIG_PHY_FSL_IMX8MQ_USB)	+= phy-fsl-imx8mq-usb.o
 obj-$(CONFIG_PHY_MIXEL_LVDS_PHY)	+= phy-fsl-imx8qm-lvds-phy.o
 obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY)	+= phy-fsl-imx8-mipi-dphy.o
 obj-$(CONFIG_PHY_FSL_IMX8M_PCIE)	+= phy-fsl-imx8m-pcie.o
+obj-$(CONFIG_PHY_FSL_IMX8QM_HSIO)	+= phy-fsl-imx8qm-hsio.o
 obj-$(CONFIG_PHY_FSL_LYNX_28G)		+= phy-fsl-lynx-28g.o
diff --git a/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c b/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
new file mode 100644
index 000000000000..73e0c50fcdae
--- /dev/null
+++ b/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
@@ -0,0 +1,612 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pci_regs.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/pcie.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+#define MAX_NUM_LANE	3
+#define LANE_NUM_CLKS	5
+
+/* Parameters for the waiting for PCIe PHY PLL to lock */
+#define PHY_INIT_WAIT_USLEEP_MAX	10
+#define PHY_INIT_WAIT_TIMEOUT		(1000 * PHY_INIT_WAIT_USLEEP_MAX)
+
+/* i.MX8Q HSIO registers */
+#define HSIO_CTRL0			0x0
+#define HSIO_APB_RSTN_0			BIT(0)
+#define HSIO_APB_RSTN_1			BIT(1)
+#define HSIO_PIPE_RSTN_0_MASK		GENMASK(25, 24)
+#define HSIO_PIPE_RSTN_1_MASK		GENMASK(27, 26)
+#define HSIO_MODE_MASK			GENMASK(20, 17)
+#define HSIO_MODE_PCIE			0x0
+#define HSIO_MODE_SATA			0x4
+#define HSIO_DEVICE_TYPE_MASK		GENMASK(27, 24)
+#define HSIO_EPCS_TXDEEMP		BIT(5)
+#define HSIO_EPCS_TXDEEMP_SEL		BIT(6)
+#define HSIO_EPCS_PHYRESET_N		BIT(7)
+#define HSIO_RESET_N			BIT(12)
+
+#define HSIO_IOB_RXENA			BIT(0)
+#define HSIO_IOB_TXENA			BIT(1)
+#define HSIO_IOB_A_0_TXOE		BIT(2)
+#define HSIO_IOB_A_0_M1M0_2		BIT(4)
+#define HSIO_IOB_A_0_M1M0_MASK		GENMASK(4, 3)
+#define HSIO_PHYX1_EPCS_SEL		BIT(12)
+#define HSIO_PCIE_AB_SELECT		BIT(13)
+
+#define HSIO_PHY_STS0			0x4
+#define HSIO_LANE0_TX_PLL_LOCK		BIT(4)
+#define HSIO_LANE1_TX_PLL_LOCK		BIT(12)
+
+#define HSIO_CTRL2			0x8
+#define HSIO_LTSSM_ENABLE		BIT(4)
+#define HSIO_BUTTON_RST_N		BIT(21)
+#define HSIO_PERST_N			BIT(22)
+#define HSIO_POWER_UP_RST_N		BIT(23)
+
+#define HSIO_PCIE_STS0			0xc
+#define HSIO_PM_REQ_CORE_RST		BIT(19)
+
+#define HSIO_REG48_PMA_STATUS		0x30
+#define HSIO_REG48_PMA_RDY		BIT(7)
+
+struct imx_hsio_drvdata {
+	int lane_num;
+};
+
+struct imx_hsio_lane {
+	u32 ctrl_index;
+	u32 ctrl_off;
+	u32 idx;
+	u32 phy_off;
+	u32 phy_type;
+	const char * const *clk_names;
+	struct clk_bulk_data clks[LANE_NUM_CLKS];
+	struct imx_hsio_priv *priv;
+	struct phy *phy;
+	enum phy_mode phy_mode;
+};
+
+struct imx_hsio_priv {
+	void __iomem *base;
+	struct device *dev;
+	struct mutex lock;
+	const char *hsio_cfg;
+	const char *refclk_pad;
+	u32 open_cnt;
+	struct regmap *phy;
+	struct regmap *ctrl;
+	struct regmap *misc;
+	const struct imx_hsio_drvdata *drvdata;
+	struct imx_hsio_lane lane[MAX_NUM_LANE];
+};
+
+static const char * const lan0_pcie_clks[] = {"apb_pclk0", "pclk0", "ctl0_crr",
+					      "phy0_crr", "misc_crr"};
+static const char * const lan1_pciea_clks[] = {"apb_pclk1", "pclk1", "ctl0_crr",
+					       "phy0_crr", "misc_crr"};
+static const char * const lan1_pcieb_clks[] = {"apb_pclk1", "pclk1", "ctl1_crr",
+					       "phy0_crr", "misc_crr"};
+static const char * const lan2_pcieb_clks[] = {"apb_pclk2", "pclk2", "ctl1_crr",
+					       "phy1_crr", "misc_crr"};
+static const char * const lan2_sata_clks[] = {"pclk2", "epcs_tx", "epcs_rx",
+					      "phy1_crr", "misc_crr"};
+
+static const struct regmap_config regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+};
+
+static int imx_hsio_init(struct phy *phy)
+{
+	int ret, i;
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+	struct device *dev = priv->dev;
+
+	/* Assign clocks refer to different modes */
+	switch (lane->phy_type) {
+	case PHY_TYPE_PCIE:
+		lane->phy_mode = PHY_MODE_PCIE;
+		if (lane->ctrl_index == 0) { /* PCIEA */
+			lane->ctrl_off = 0;
+			lane->phy_off = 0;
+
+			for (i = 0; i < LANE_NUM_CLKS; i++) {
+				if (lane->idx == 0)
+					lane->clks[i].id = lan0_pcie_clks[i];
+				else
+					lane->clks[i].id = lan1_pciea_clks[i];
+			}
+		} else { /* PCIEB */
+			if (lane->idx == 0) { /* i.MX8QXP */
+				lane->ctrl_off = 0;
+				lane->phy_off = 0;
+			} else {
+				/*
+				 * On i.MX8QM, only second or third lane can be
+				 * bound to PCIEB.
+				 */
+				lane->ctrl_off = SZ_64K;
+				if (lane->idx == 1)
+					lane->phy_off = 0;
+				else /* the third lane is bound to PCIEB */
+					lane->phy_off = SZ_64K;
+			}
+
+			for (i = 0; i < LANE_NUM_CLKS; i++) {
+				if (lane->idx == 1)
+					lane->clks[i].id = lan1_pcieb_clks[i];
+				else if (lane->idx == 2)
+					lane->clks[i].id = lan2_pcieb_clks[i];
+				else /* i.MX8QXP only has PCIEB, idx is 0 */
+					lane->clks[i].id = lan0_pcie_clks[i];
+			}
+		}
+		break;
+	case PHY_TYPE_SATA:
+		/* On i.MX8QM, only the third lane can be bound to SATA */
+		lane->phy_mode = PHY_MODE_SATA;
+		lane->ctrl_off = SZ_128K;
+		lane->phy_off = SZ_64K;
+
+		for (i = 0; i < LANE_NUM_CLKS; i++)
+			lane->clks[i].id = lan2_sata_clks[i];
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* Fetch clocks and enable them */
+	ret = devm_clk_bulk_get(dev, LANE_NUM_CLKS, lane->clks);
+	if (ret)
+		return ret;
+	ret = clk_bulk_prepare_enable(LANE_NUM_CLKS, lane->clks);
+	if (ret)
+		return ret;
+
+	/* allow the clocks to stabilize */
+	usleep_range(200, 500);
+	return 0;
+}
+
+static int imx_hsio_exit(struct phy *phy)
+{
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+
+	clk_bulk_disable_unprepare(LANE_NUM_CLKS, lane->clks);
+
+	return 0;
+}
+
+static void imx_hsio_pcie_phy_resets(struct phy *phy)
+{
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			  HSIO_BUTTON_RST_N);
+	regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			  HSIO_PERST_N);
+	regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			  HSIO_POWER_UP_RST_N);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			HSIO_BUTTON_RST_N);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			HSIO_PERST_N);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			HSIO_POWER_UP_RST_N);
+
+	if (lane->idx == 1) {
+		regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
+				HSIO_APB_RSTN_1);
+		regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
+				HSIO_PIPE_RSTN_1_MASK);
+	} else {
+		regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
+				HSIO_APB_RSTN_0);
+		regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
+				HSIO_PIPE_RSTN_0_MASK);
+	}
+}
+
+static void imx_hsio_sata_phy_resets(struct phy *phy)
+{
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	/* clear PHY RST, then set it */
+	regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
+			  HSIO_EPCS_PHYRESET_N);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
+			HSIO_EPCS_PHYRESET_N);
+
+	/* CTRL RST: SET -> delay 1 us -> CLEAR -> SET */
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0, HSIO_RESET_N);
+	udelay(1);
+	regmap_clear_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
+			  HSIO_RESET_N);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0, HSIO_RESET_N);
+}
+
+static void imx_hsio_configure_clk_pad(struct phy *phy)
+{
+	bool pll = false;
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	if (strncmp(priv->refclk_pad, "output", 6) == 0) {
+		pll = true;
+		regmap_update_bits(priv->misc, HSIO_CTRL0,
+				   HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_MASK,
+				   HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_2);
+	} else {
+		regmap_update_bits(priv->misc, HSIO_CTRL0,
+				   HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_MASK,
+				   0);
+	}
+
+	regmap_update_bits(priv->misc, HSIO_CTRL0, HSIO_IOB_RXENA,
+			   pll ? 0 : HSIO_IOB_RXENA);
+	regmap_update_bits(priv->misc, HSIO_CTRL0, HSIO_IOB_TXENA,
+			   pll ? HSIO_IOB_TXENA : 0);
+}
+
+static void imx_hsio_pre_set(struct phy *phy)
+{
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	if (strncmp(priv->hsio_cfg, "pcieax2pcieb", 10) == 0) {
+		regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PCIE_AB_SELECT);
+	} else if (strncmp(priv->hsio_cfg, "pcieax2sata", 9) == 0) {
+		regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PHYX1_EPCS_SEL);
+	} else if (strncmp(priv->hsio_cfg, "pcieapciebsata", 12) == 0) {
+		regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PCIE_AB_SELECT);
+		regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PHYX1_EPCS_SEL);
+	}
+
+	imx_hsio_configure_clk_pad(phy);
+}
+
+static int imx_hsio_pcie_power_on(struct phy *phy)
+{
+	int ret;
+	u32 val, addr, cond;
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	imx_hsio_pcie_phy_resets(phy);
+
+	/* Toggle apb_pclk to make sure PM_REQ_CORE_RST is cleared. */
+	clk_disable_unprepare(lane->clks[0].clk);
+	mdelay(1);
+	ret = clk_prepare_enable(lane->clks[0].clk);
+	if (ret) {
+		dev_err(priv->dev, "unable to enable phy apb_pclk\n");
+		return ret;
+	}
+
+	addr = lane->ctrl_off + HSIO_PCIE_STS0;
+	cond = HSIO_PM_REQ_CORE_RST;
+	ret = regmap_read_poll_timeout(priv->ctrl, addr, val,
+				       (val & cond) == 0,
+				       PHY_INIT_WAIT_USLEEP_MAX,
+				       PHY_INIT_WAIT_TIMEOUT);
+	if (ret)
+		dev_err(priv->dev, "HSIO_PM_REQ_CORE_RST is set\n");
+	return ret;
+}
+
+static int imx_hsio_sata_power_on(struct phy *phy)
+{
+	int ret;
+	u32 val, cond;
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	regmap_set_bits(priv->phy, lane->phy_off + HSIO_CTRL0, HSIO_APB_RSTN_0);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
+			HSIO_EPCS_TXDEEMP);
+	regmap_set_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
+			HSIO_EPCS_TXDEEMP_SEL);
+
+	imx_hsio_sata_phy_resets(phy);
+
+	cond = HSIO_REG48_PMA_RDY;
+	ret = read_poll_timeout(readb, val, ((val & cond) == cond),
+				PHY_INIT_WAIT_USLEEP_MAX,
+				PHY_INIT_WAIT_TIMEOUT, false,
+				priv->base + HSIO_REG48_PMA_STATUS);
+	if (ret)
+		dev_err(priv->dev, "PHY calibration is timeout\n");
+	else
+		dev_dbg(priv->dev, "PHY calibration is done\n");
+
+	return ret;
+}
+
+static int imx_hsio_power_on(struct phy *phy)
+{
+	int ret;
+	u32 val, cond;
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	scoped_guard(mutex, &priv->lock) {
+		if (!priv->open_cnt)
+			imx_hsio_pre_set(phy);
+		priv->open_cnt++;
+	}
+
+	if (lane->phy_mode == PHY_MODE_PCIE)
+		ret = imx_hsio_pcie_power_on(phy);
+	else /* SATA */
+		ret = imx_hsio_sata_power_on(phy);
+	if (ret)
+		return ret;
+
+	/* Polling to check the PHY is ready or not. */
+	if (lane->idx == 1)
+		cond = HSIO_LANE1_TX_PLL_LOCK;
+	else
+		/*
+		 * Except the phy_off, the bit-offset of lane2 is same to lane0.
+		 * Merge the lane0 and lane2 bit-operations together.
+		 */
+		cond = HSIO_LANE0_TX_PLL_LOCK;
+
+	ret = regmap_read_poll_timeout(priv->phy, lane->phy_off + HSIO_PHY_STS0,
+				       val, ((val & cond) == cond),
+				       PHY_INIT_WAIT_USLEEP_MAX,
+				       PHY_INIT_WAIT_TIMEOUT);
+	if (ret) {
+		dev_err(priv->dev, "IMX8Q PHY%d PLL lock timeout\n", lane->idx);
+		return ret;
+	}
+	dev_dbg(priv->dev, "IMX8Q PHY%d PLL is locked\n", lane->idx);
+
+	return ret;
+}
+
+static int imx_hsio_power_off(struct phy *phy)
+{
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	scoped_guard(mutex, &priv->lock) {
+		priv->open_cnt--;
+		if (priv->open_cnt == 0) {
+			regmap_clear_bits(priv->misc, HSIO_CTRL0,
+					  HSIO_PCIE_AB_SELECT);
+			regmap_clear_bits(priv->misc, HSIO_CTRL0,
+					  HSIO_PHYX1_EPCS_SEL);
+
+			if (lane->phy_mode == PHY_MODE_PCIE) {
+				regmap_clear_bits(priv->ctrl,
+						  lane->ctrl_off + HSIO_CTRL2,
+						  HSIO_BUTTON_RST_N);
+				regmap_clear_bits(priv->ctrl,
+						  lane->ctrl_off + HSIO_CTRL2,
+						  HSIO_PERST_N);
+				regmap_clear_bits(priv->ctrl,
+						  lane->ctrl_off + HSIO_CTRL2,
+						  HSIO_POWER_UP_RST_N);
+			} else {
+				regmap_clear_bits(priv->ctrl,
+						  lane->ctrl_off + HSIO_CTRL0,
+						  HSIO_EPCS_TXDEEMP);
+				regmap_clear_bits(priv->ctrl,
+						  lane->ctrl_off + HSIO_CTRL0,
+						  HSIO_EPCS_TXDEEMP_SEL);
+				regmap_clear_bits(priv->ctrl,
+						  lane->ctrl_off + HSIO_CTRL0,
+						  HSIO_RESET_N);
+			}
+
+			if (lane->idx == 1) {
+				regmap_clear_bits(priv->phy,
+						  lane->phy_off + HSIO_CTRL0,
+						  HSIO_APB_RSTN_1);
+				regmap_clear_bits(priv->phy,
+						  lane->phy_off + HSIO_CTRL0,
+						  HSIO_PIPE_RSTN_1_MASK);
+			} else {
+				/*
+				 * Except the phy_off, the bit-offset of lane2 is same
+				 * to lane0. Merge the lane0 and lane2 bit-operations
+				 * together.
+				 */
+				regmap_clear_bits(priv->phy,
+						  lane->phy_off + HSIO_CTRL0,
+						  HSIO_APB_RSTN_0);
+				regmap_clear_bits(priv->phy,
+						  lane->phy_off + HSIO_CTRL0,
+						  HSIO_PIPE_RSTN_0_MASK);
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int imx_hsio_set_mode(struct phy *phy, enum phy_mode mode,
+			     int submode)
+{
+	u32 val;
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	if (lane->phy_mode != mode)
+		return -EINVAL;
+
+	val = (mode == PHY_MODE_PCIE) ? HSIO_MODE_PCIE : HSIO_MODE_SATA;
+	val = FIELD_PREP(HSIO_MODE_MASK, val);
+	regmap_update_bits(priv->phy, lane->phy_off + HSIO_CTRL0,
+			   HSIO_MODE_MASK, val);
+
+	switch (submode) {
+	case PHY_MODE_PCIE_RC:
+		val = FIELD_PREP(HSIO_DEVICE_TYPE_MASK, PCI_EXP_TYPE_ROOT_PORT);
+		break;
+	case PHY_MODE_PCIE_EP:
+		val = FIELD_PREP(HSIO_DEVICE_TYPE_MASK, PCI_EXP_TYPE_ENDPOINT);
+		break;
+	default: /* Support only PCIe EP and RC now. */
+		return 0;
+	}
+	if (submode)
+		regmap_update_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL0,
+				   HSIO_DEVICE_TYPE_MASK, val);
+
+	return 0;
+}
+
+static int imx_hsio_set_speed(struct phy *phy, int speed)
+{
+	struct imx_hsio_lane *lane = phy_get_drvdata(phy);
+	struct imx_hsio_priv *priv = lane->priv;
+
+	regmap_update_bits(priv->ctrl, lane->ctrl_off + HSIO_CTRL2,
+			   HSIO_LTSSM_ENABLE,
+			   speed ? HSIO_LTSSM_ENABLE : 0);
+	return 0;
+}
+
+static const struct phy_ops imx_hsio_ops = {
+	.init = imx_hsio_init,
+	.exit = imx_hsio_exit,
+	.power_on = imx_hsio_power_on,
+	.power_off = imx_hsio_power_off,
+	.set_mode = imx_hsio_set_mode,
+	.set_speed = imx_hsio_set_speed,
+	.owner = THIS_MODULE,
+};
+
+static const struct imx_hsio_drvdata imx8qxp_hsio_drvdata = {
+	.lane_num = 0x1,
+};
+
+static const struct imx_hsio_drvdata imx_hsio_drvdata = {
+	.lane_num = 0x3,
+};
+
+static const struct of_device_id imx_hsio_of_match[] = {
+	{.compatible = "fsl,imx8qm-hsio", .data = &imx_hsio_drvdata},
+	{.compatible = "fsl,imx8qxp-hsio", .data = &imx8qxp_hsio_drvdata},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, imx_hsio_of_match);
+
+static struct phy *imx_hsio_xlate(struct device *dev,
+				  const struct of_phandle_args *args)
+{
+	struct imx_hsio_priv *priv = dev_get_drvdata(dev);
+	int idx = args->args[0];
+	int phy_type = args->args[1];
+	int ctrl_index = args->args[2];
+
+	if (idx < 0 || idx >= priv->drvdata->lane_num)
+		return ERR_PTR(-EINVAL);
+	priv->lane[idx].idx = idx;
+	priv->lane[idx].phy_type = phy_type;
+	priv->lane[idx].ctrl_index = ctrl_index;
+
+	return priv->lane[idx].phy;
+}
+
+static int imx_hsio_probe(struct platform_device *pdev)
+{
+	int i;
+	void __iomem *off;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct imx_hsio_priv *priv;
+	struct phy_provider *provider;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+	priv->dev = &pdev->dev;
+	priv->drvdata = of_device_get_match_data(dev);
+
+	/* Get HSIO configuration mode */
+	if (of_property_read_string(np, "fsl,hsio-cfg", &priv->hsio_cfg))
+		priv->hsio_cfg = "pcieapciebsata";
+	/* Get PHY refclk pad mode */
+	if (of_property_read_string(np, "fsl,refclk-pad-mode",
+				    &priv->refclk_pad))
+		priv->refclk_pad = NULL;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	off = devm_platform_ioremap_resource_byname(pdev, "phy");
+	priv->phy = devm_regmap_init_mmio(dev, off, &regmap_config);
+	if (IS_ERR(priv->phy))
+		return dev_err_probe(dev, PTR_ERR(priv->phy),
+				     "unable to find phy csr registers\n");
+
+	off = devm_platform_ioremap_resource_byname(pdev, "ctrl");
+	priv->ctrl = devm_regmap_init_mmio(dev, off, &regmap_config);
+	if (IS_ERR(priv->ctrl))
+		return dev_err_probe(dev, PTR_ERR(priv->ctrl),
+				     "unable to find ctrl csr registers\n");
+
+	off = devm_platform_ioremap_resource_byname(pdev, "misc");
+	priv->misc = devm_regmap_init_mmio(dev, off, &regmap_config);
+	if (IS_ERR(priv->misc))
+		return dev_err_probe(dev, PTR_ERR(priv->misc),
+				     "unable to find misc csr registers\n");
+
+	for (i = 0; i < priv->drvdata->lane_num; i++) {
+		struct imx_hsio_lane *lane = &priv->lane[i];
+		struct phy *phy;
+
+		memset(lane, 0, sizeof(*lane));
+
+		phy = devm_phy_create(&pdev->dev, NULL, &imx_hsio_ops);
+		if (IS_ERR(phy))
+			return PTR_ERR(phy);
+
+		lane->priv = priv;
+		lane->phy = phy;
+		lane->idx = i;
+		phy_set_drvdata(phy, lane);
+	}
+
+	dev_set_drvdata(dev, priv);
+	dev_set_drvdata(&pdev->dev, priv);
+
+	provider = devm_of_phy_provider_register(&pdev->dev, imx_hsio_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static struct platform_driver imx_hsio_driver = {
+	.probe	= imx_hsio_probe,
+	.driver = {
+		.name	= "imx8qm-hsio-phy",
+		.of_match_table	= imx_hsio_of_match,
+	}
+};
+module_platform_driver(imx_hsio_driver);
+
+MODULE_DESCRIPTION("FSL IMX8QM HSIO SERDES PHY driver");
+MODULE_LICENSE("GPL");
-- 
2.37.1





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux