Re: [PATCH 2/2] drm: panel: nv3052c: Add WL-355608-A8 panel

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Fri, May 24, 2024 at 10:33:14PM +1200, Ryan Walklin wrote:
> The WL-355608-A8 is a 3.5" 640x480@60Hz RGB LCD display from an unknown
> OEM, used in a number of handheld gaming devices made by Anbernic.
> 
> Limited information is available online however the panel timing values
> (below) have been obtained from the vendor BSP. The panel appears to
> integrate a NV3052C LCD driver (or clone). Available devices address it
> in SPI/RGB mode, with the timing signals generated from the device
> SoC (in testing hardware an Allwinner H700) and passed through.
> 
> Add a panel definition and display mode to the existing NV3502C driver.
> 
> It was assumed during bringup that the initialisation sequence was the
> same as the existing Fascontek FS035VG158 panel, proved working during
> experimentation. However subsequent dumping of the init sequence with a
> logic analyser confirms one small change to VCOM_ADJ3 from 0x4a to 0x44,
> therefore a separate set of registers is also added.
> 
> Timings:
>            | Active |  FP  | Sync |  BP  | Total
> -----------|--------|------|------|------|-------
> Horizontal |   640  |  64  |  20  |  46  |  770
>   Vertical |   480  |  21  |   4  |  15  |  520
> 
> Signed-off-by: Ryan Walklin <ryan@xxxxxxxxxxxxx>
> Co-developed-by: Hironori KIKUCHI <kikuchan98@xxxxxxxxx>
> ---
>  .../gpu/drm/panel/panel-newvision-nv3052c.c   | 225 ++++++++++++++++++
>  1 file changed, 225 insertions(+)
> 
> diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> index 1aab0c9ae..5de36ecec 100644
> --- a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> +++ b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> @@ -433,6 +433,202 @@ static const struct nv3052c_reg fs035vg158_panel_regs[] = {
>  	{ 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
>  };
>  
> +
> +static const struct nv3052c_reg wl_355608_a8_panel_regs[] = {
> +	// EXTC Command set enable, select page 1
> +	{ 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x01 },
> +	// Mostly unknown registers
> +	{ 0xe3, 0x00 },
> +	{ 0x40, 0x00 },
> +	{ 0x03, 0x40 },
> +	{ 0x04, 0x00 },
> +	{ 0x05, 0x03 },
> +	{ 0x08, 0x00 },
> +	{ 0x09, 0x07 },
> +	{ 0x0a, 0x01 },
> +	{ 0x0b, 0x32 },
> +	{ 0x0c, 0x32 },
> +	{ 0x0d, 0x0b },
> +	{ 0x0e, 0x00 },
> +	{ 0x23, 0xa0 },
> +	{ 0x24, 0x0c },
> +	{ 0x25, 0x06 },
> +	{ 0x26, 0x14 },
> +	{ 0x27, 0x14 },
> +	{ 0x38, 0xcc }, // VCOM_ADJ1
> +	{ 0x39, 0xd7 }, // VCOM_ADJ2
> +	{ 0x3a, 0x44 }, // VCOM_ADJ3
> +	{ 0x28, 0x40 },
> +	{ 0x29, 0x01 },
> +	{ 0x2a, 0xdf },
> +	{ 0x49, 0x3c },
> +	{ 0x91, 0x77 }, // EXTPW_CTRL2
> +	{ 0x92, 0x77 }, // EXTPW_CTRL3
> +	{ 0xa0, 0x55 },
> +	{ 0xa1, 0x50 },
> +	{ 0xa4, 0x9c },
> +	{ 0xa7, 0x02 },
> +	{ 0xa8, 0x01 },
> +	{ 0xa9, 0x01 },
> +	{ 0xaa, 0xfc },
> +	{ 0xab, 0x28 },
> +	{ 0xac, 0x06 },
> +	{ 0xad, 0x06 },
> +	{ 0xae, 0x06 },
> +	{ 0xaf, 0x03 },
> +	{ 0xb0, 0x08 },
> +	{ 0xb1, 0x26 },
> +	{ 0xb2, 0x28 },
> +	{ 0xb3, 0x28 },
> +	{ 0xb4, 0x33 },
> +	{ 0xb5, 0x08 },
> +	{ 0xb6, 0x26 },
> +	{ 0xb7, 0x08 },
> +	{ 0xb8, 0x26 },
> +	{ 0xf0, 0x00 },
> +	{ 0xf6, 0xc0 },
> +	// EXTC Command set enable, select page 2
> +	{ 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
> +	// Set gray scale voltage to adjust gamma
> +	{ 0xb0, 0x0b }, // PGAMVR0
> +	{ 0xb1, 0x16 }, // PGAMVR1
> +	{ 0xb2, 0x17 }, // PGAMVR2
> +	{ 0xb3, 0x2c }, // PGAMVR3
> +	{ 0xb4, 0x32 }, // PGAMVR4
> +	{ 0xb5, 0x3b }, // PGAMVR5
> +	{ 0xb6, 0x29 }, // PGAMPR0
> +	{ 0xb7, 0x40 }, // PGAMPR1
> +	{ 0xb8, 0x0d }, // PGAMPK0
> +	{ 0xb9, 0x05 }, // PGAMPK1
> +	{ 0xba, 0x12 }, // PGAMPK2
> +	{ 0xbb, 0x10 }, // PGAMPK3
> +	{ 0xbc, 0x12 }, // PGAMPK4
> +	{ 0xbd, 0x15 }, // PGAMPK5
> +	{ 0xbe, 0x19 }, // PGAMPK6
> +	{ 0xbf, 0x0e }, // PGAMPK7
> +	{ 0xc0, 0x16 }, // PGAMPK8
> +	{ 0xc1, 0x0a }, // PGAMPK9
> +	// Set gray scale voltage to adjust gamma
> +	{ 0xd0, 0x0c }, // NGAMVR0
> +	{ 0xd1, 0x17 }, // NGAMVR0
> +	{ 0xd2, 0x14 }, // NGAMVR1
> +	{ 0xd3, 0x2e }, // NGAMVR2
> +	{ 0xd4, 0x32 }, // NGAMVR3
> +	{ 0xd5, 0x3c }, // NGAMVR4
> +	{ 0xd6, 0x22 }, // NGAMPR0
> +	{ 0xd7, 0x3d }, // NGAMPR1
> +	{ 0xd8, 0x0d }, // NGAMPK0
> +	{ 0xd9, 0x07 }, // NGAMPK1
> +	{ 0xda, 0x13 }, // NGAMPK2
> +	{ 0xdb, 0x13 }, // NGAMPK3
> +	{ 0xdc, 0x11 }, // NGAMPK4
> +	{ 0xdd, 0x15 }, // NGAMPK5
> +	{ 0xde, 0x19 }, // NGAMPK6
> +	{ 0xdf, 0x10 }, // NGAMPK7
> +	{ 0xe0, 0x17 }, // NGAMPK8
> +	{ 0xe1, 0x0a }, // NGAMPK9
> +	// EXTC Command set enable, select page 3
> +	{ 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x03 },
> +	// Set various timing settings
> +	{ 0x00, 0x2a }, // GIP_VST_1
> +	{ 0x01, 0x2a }, // GIP_VST_2
> +	{ 0x02, 0x2a }, // GIP_VST_3
> +	{ 0x03, 0x2a }, // GIP_VST_4
> +	{ 0x04, 0x61 }, // GIP_VST_5
> +	{ 0x05, 0x80 }, // GIP_VST_6
> +	{ 0x06, 0xc7 }, // GIP_VST_7
> +	{ 0x07, 0x01 }, // GIP_VST_8
> +	{ 0x08, 0x03 }, // GIP_VST_9
> +	{ 0x09, 0x04 }, // GIP_VST_10
> +	{ 0x70, 0x22 }, // GIP_ECLK1
> +	{ 0x71, 0x80 }, // GIP_ECLK2
> +	{ 0x30, 0x2a }, // GIP_CLK_1
> +	{ 0x31, 0x2a }, // GIP_CLK_2
> +	{ 0x32, 0x2a }, // GIP_CLK_3
> +	{ 0x33, 0x2a }, // GIP_CLK_4
> +	{ 0x34, 0x61 }, // GIP_CLK_5
> +	{ 0x35, 0xc5 }, // GIP_CLK_6
> +	{ 0x36, 0x80 }, // GIP_CLK_7
> +	{ 0x37, 0x23 }, // GIP_CLK_8
> +	{ 0x40, 0x03 }, // GIP_CLKA_1
> +	{ 0x41, 0x04 }, // GIP_CLKA_2
> +	{ 0x42, 0x05 }, // GIP_CLKA_3
> +	{ 0x43, 0x06 }, // GIP_CLKA_4
> +	{ 0x44, 0x11 }, // GIP_CLKA_5
> +	{ 0x45, 0xe8 }, // GIP_CLKA_6
> +	{ 0x46, 0xe9 }, // GIP_CLKA_7
> +	{ 0x47, 0x11 }, // GIP_CLKA_8
> +	{ 0x48, 0xea }, // GIP_CLKA_9
> +	{ 0x49, 0xeb }, // GIP_CLKA_10
> +	{ 0x50, 0x07 }, // GIP_CLKB_1
> +	{ 0x51, 0x08 }, // GIP_CLKB_2
> +	{ 0x52, 0x09 }, // GIP_CLKB_3
> +	{ 0x53, 0x0a }, // GIP_CLKB_4
> +	{ 0x54, 0x11 }, // GIP_CLKB_5
> +	{ 0x55, 0xec }, // GIP_CLKB_6
> +	{ 0x56, 0xed }, // GIP_CLKB_7
> +	{ 0x57, 0x11 }, // GIP_CLKB_8
> +	{ 0x58, 0xef }, // GIP_CLKB_9
> +	{ 0x59, 0xf0 }, // GIP_CLKB_10
> +	// Map internal GOA signals to GOA output pad
> +	{ 0xb1, 0x01 }, // PANELD2U2
> +	{ 0xb4, 0x15 }, // PANELD2U5
> +	{ 0xb5, 0x16 }, // PANELD2U6
> +	{ 0xb6, 0x09 }, // PANELD2U7
> +	{ 0xb7, 0x0f }, // PANELD2U8
> +	{ 0xb8, 0x0d }, // PANELD2U9
> +	{ 0xb9, 0x0b }, // PANELD2U10
> +	{ 0xba, 0x00 }, // PANELD2U11
> +	{ 0xc7, 0x02 }, // PANELD2U24
> +	{ 0xca, 0x17 }, // PANELD2U27
> +	{ 0xcb, 0x18 }, // PANELD2U28
> +	{ 0xcc, 0x0a }, // PANELD2U29
> +	{ 0xcd, 0x10 }, // PANELD2U30
> +	{ 0xce, 0x0e }, // PANELD2U31
> +	{ 0xcf, 0x0c }, // PANELD2U32
> +	{ 0xd0, 0x00 }, // PANELD2U33
> +	// Map internal GOA signals to GOA output pad
> +	{ 0x81, 0x00 }, // PANELU2D2
> +	{ 0x84, 0x15 }, // PANELU2D5
> +	{ 0x85, 0x16 }, // PANELU2D6
> +	{ 0x86, 0x10 }, // PANELU2D7
> +	{ 0x87, 0x0a }, // PANELU2D8
> +	{ 0x88, 0x0c }, // PANELU2D9
> +	{ 0x89, 0x0e }, // PANELU2D10
> +	{ 0x8a, 0x02 }, // PANELU2D11
> +	{ 0x97, 0x00 }, // PANELU2D24
> +	{ 0x9a, 0x17 }, // PANELU2D27
> +	{ 0x9b, 0x18 }, // PANELU2D28
> +	{ 0x9c, 0x0f }, // PANELU2D29
> +	{ 0x9d, 0x09 }, // PANELU2D30
> +	{ 0x9e, 0x0b }, // PANELU2D31
> +	{ 0x9f, 0x0d }, // PANELU2D32
> +	{ 0xa0, 0x01 }, // PANELU2D33
> +	// EXTC Command set enable, select page 2
> +	{ 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
> +	// Unknown registers
> +	{ 0x01, 0x01 },
> +	{ 0x02, 0xda },
> +	{ 0x03, 0xba },
> +	{ 0x04, 0xa8 },
> +	{ 0x05, 0x9a },
> +	{ 0x06, 0x70 },
> +	{ 0x07, 0xff },
> +	{ 0x08, 0x91 },
> +	{ 0x09, 0x90 },
> +	{ 0x0a, 0xff },
> +	{ 0x0b, 0x8f },
> +	{ 0x0c, 0x60 },
> +	{ 0x0d, 0x58 },
> +	{ 0x0e, 0x48 },
> +	{ 0x0f, 0x38 },
> +	{ 0x10, 0x2b },
> +	// EXTC Command set enable, select page 0
> +	{ 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x00 },
> +	// Display Access Control
> +	{ 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
> +};
> +
>  static inline struct nv3052c *to_nv3052c(struct drm_panel *panel)
>  {
>  	return container_of(panel, struct nv3052c, panel);
> @@ -670,6 +866,21 @@ static const struct drm_display_mode fs035vg158_modes[] = {
>  	},
>  };
>  
> +static const struct drm_display_mode wl_355608_a8_mode[] = {
> +	{
> +		.clock = 24000,
> +		.hdisplay = 640,
> +		.hsync_start = 640 + 64,
> +		.hsync_end = 640 + 64 + 20, 
> +		.htotal = 640 + 64 + 20 + 46,
> +		.vdisplay = 480,
> +		.vsync_start = 480 + 21,
> +		.vsync_end = 480 + 21 + 4,
> +		.vtotal = 480 + 21 + 4 + 15, 
> +		.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC, 
> +	},
> +};
> +
>  static const struct nv3052c_panel_info ltk035c5444t_panel_info = {
>  	.display_modes = ltk035c5444t_modes,
>  	.num_modes = ARRAY_SIZE(ltk035c5444t_modes),
> @@ -692,9 +903,21 @@ static const struct nv3052c_panel_info fs035vg158_panel_info = {
>  	.panel_regs_len = ARRAY_SIZE(fs035vg158_panel_regs),
>  };
>  
> +static const struct nv3052c_panel_info wl_355608_a8_panel_info = {
> +	.display_modes = wl_355608_a8_mode,
> +	.num_modes = ARRAY_SIZE(wl_355608_a8_mode),
> +	.width_mm = 150,
> +	.height_mm = 94,
> +	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> +	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
> +	.panel_regs = wl_355608_a8_panel_regs,
> +	.panel_regs_len = ARRAY_SIZE(wl_355608_a8_panel_regs),
> +};
> +
>  static const struct spi_device_id nv3052c_ids[] = {
>  	{ "ltk035c5444t", },
>  	{ "fs035vg158", },
> +	{ "wl_355608_a8", },
>  	{ /* sentinel */ }
>  };
>  MODULE_DEVICE_TABLE(spi, nv3052c_ids);
> @@ -702,6 +925,7 @@ MODULE_DEVICE_TABLE(spi, nv3052c_ids);
>  static const struct of_device_id nv3052c_of_match[] = {
>  	{ .compatible = "leadtek,ltk035c5444t", .data = &ltk035c5444t_panel_info },
>  	{ .compatible = "fascontek,fs035vg158", .data = &fs035vg158_panel_info },
> +	{ .compatible = "wl_355608_a8", .data = &wl_355608_a8_panel_info },
>  	{ /* sentinel */ }
>  };
>  MODULE_DEVICE_TABLE(of, nv3052c_of_match);
> @@ -719,4 +943,5 @@ module_spi_driver(nv3052c_driver);
>  
>  MODULE_AUTHOR("Paul Cercueil <paul@xxxxxxxxxxxxxxx>");
>  MODULE_AUTHOR("Christophe Branchereau <cbranchereau@xxxxxxxxx>");
> +MODULE_AUTHOR("Ryan Walklin <ryan@xxxxxxxxxxxxx");
>  MODULE_LICENSE("GPL v2");
> -- 
> 2.45.1
> 

This all looks good to me, though I understand you may need to change the
compatible. Please CC me if this happens so I can re-review.

Reviewed-by: John Watts <contact@xxxxxxxxxx>

John.




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux