Changelog:
- v8
- add fan led config
- v7
- Revise pca9506 i2c address
- v6
- Revise i2c duty-cycle for meeting 400khz spec
- v5
- Support medusa board adc sensors
- support NIC eeprom
- v4
- Re-format gpio linename
- Revise i2c device node names
- Split patches by logic changes
- v3
- Correct patch for revising gpio name
- v2
- Revise mx31790 fan tach config
- Add mctp config for NIC
- Support mux to cpld
- Revise gpio name
- v1
- Add gpio and eeprom behind i2c-mux
- Remove redundant idle-state setting for i2c-mux
- Enable adc 15, wdt2,spi gpio for yosemite4 use
- Revise quad mode to dual mode to avoid WP pin influnece the SPI
- Revise power sensor adm1281 for yosemite4 schematic change
- Add gpio pca9506 I/O expander for yosemite4 use
- remove space for adm1272 compatible
- enable interrupt setting for pca9555
- add eeprom for yosemite4 medusa board/BSM use
- remove temperature sensor for yosemite4 schematic change
- add power sensor for power module reading
- Revise adc128d818 adc mode for yosemite4 schematic change
- Revise ina233 for yosemite4 schematic change
- Remove idle state setting for yosemite4 NIC connection
- Initialize bmc gpio state
- Revise mx31790 fan tach config
- Add mctp config for NIC
- Support mux to cpld
- Revise gpio name
Delphine CC Chiu (23):
ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
ARM: dts: aspeed: yosemite4: Enable adc15
ARM: dts: aspeed: yosemite4: Enable spi-gpio setting
ARM: dts: aspeed: yosemite4: Enable watchdog2
ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode
ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic
change
ARM: dts: aspeed: yosemite4: Add gpio pca9506
ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible
ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555
ARM: dts: aspeed: yosemite4: Add power sensor for power module reading
ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use
ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4
schematic change
ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4
schematic change
ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4
schematic change
ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4
NIC connection
ARM: dts: aspeed: yosemite4: Initialize bmc gpio state
ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config
ARM: dts: aspeed: yosemite4: add mctp config for NIC
ARM: dts: aspeed: yosemite4: support mux to cpld
ARM: dts: aspeed: yosemite4: support medusa board adc sensors
ARM: dts: aspeed: yosemite4: support NIC eeprom
ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle
ARM: dts: aspeed: yosemite4: add fan led config
.../aspeed/aspeed-bmc-facebook-yosemite4.dts | 1410 +++++++++++++++--
1 file changed, 1301 insertions(+), 109 deletions(-)
--
2.25.1
