This patch series adds support for the Analog Devices AD4111, AD4112,
AD4114, AD4115, AD4116 within the existing AD7173 driver.
The AD411X family encompasses a series of low power, low noise, 24-bit,
sigma-delta analog-to-digital converters that offer a versatile range of
specifications. They integrate an analog front end suitable for processing
fully differential/single-ended and bipolar voltage inputs.
Particularities of the models:
- All ADCs have inputs with a precision voltage divider with a division
ratio of 10.
- AD4116 has 5 low level inputs without a voltage divider.
- AD4111 and AD4112 support current inputs (0 mA to 20 mA) using a 50ohm
shunt resistor.
Discussions from this patch series have concluded with:
-Datasheets mention single-ended and pseudo differential capabilities by
the means of connecting the negative input of a differential pair (IN-)
to a constant voltage supply and letting the positive input fluctuate.
This is not a special operating mode, it is a capability of the
differential channels to also measure such signals.
-Single-ended and pseudo differential do not need any specific
configuration and cannot be differentiated from differential usage by
the driver side =>
offer adi,channel-type attribute to flag the usage of the channel
-VINCOM is described as a dedicated pin for single-ended channels but as
seen in AD4116, it is a normal input connected to the cross-point
multiplexer (VIN10, VINCOM (single-ended or differential pair)).
This does not mean full functionality in any configuration:
AD4111:"If any two voltage inputs are paired in a configuration other
than what is described in this data sheet, the accuracy of the device
cannot be guaranteed".
-ADCIN15 input pin from AD4116 is specified as the dedicated pin for
pseudo-differential but from the datasheet it results that this pin is
also able to measure single-ended and fully differential channels
("ADCIN11, ADCIN15. (pseudo differential or differential pair)";
"An example is to connect the ADCIN15 pin externally to the AVSS
pin in a single-ended configuration")
As such, detecting the type of usage of a channel is not possible and
will be the responsability of the user to specify.
If the user has connected a non 0V (in regards to AVSS) supply to
the negative input pin of a channel in a pseudo differential
configuration, the offset of the measurement from AVSS will not be known
from the driver and will need to be measured by other means.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/AD4111.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD4112.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD4114.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD4115.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD4116.pdf
This series depends on patch:
(iio: adc: ad7173: Use device_for_each_child_node_scoped() to simplify error paths.)
https://lore.kernel.org/all/20240330190849.1321065-6-jic23@xxxxxxxxxx
Signed-off-by: Dumitru Ceclan <mitrutzceclan@xxxxxxxxx>
---
Changes in v2:
dt-bindings: adc: ad7173: add support for ad411x
- Add constraint for missing avdd2-supply on ad411x
- Change support for current channels to selecting the actual
diff-channels input values and activating the
adi,current-channel property
- Add constraint for adi,current-channel
- Add adi,channel-type to be able to differentiante in the driver
between single-ended, pseudo-differential and differential channels.
- Update diff-channels description to decribe inputs beside the AINs
iio: adc: ad7173: fix buffers enablement for ad7176-2
- Specify ".has_input_buf = false" for AD7176-2
- Drop fixes tag, specify that configuration bits are read only
iio: adc: ad7173: refactor channel configuration parsing
- Add Link and Suggested-by in commit message
iio: adc: ad7173: refactor ain and vref selection
- Improve commit message to express commit purpose
- Refactor line wrappings due to reduced indent
- Change AINs check to a loop
iio: adc: ad7173: add support for special inputs
- Create patch
iio: adc: ad7173: Add ad7173_device_info names
- Create patch
iio: adc: ad7173: Remove index from temp channel
- Justify in commit message userspace breakage
- Remove index from the correct channel template
iio: adc: ad7173: Add support for AD411x devices
- Add missing validation for VCOM and inputs with voltage divider
- Add missing validation for AD4116 low level inputs
- Add missing ad7173_device_info names
- Add support for setting differential flag depending on the channel type
- Change current channel validation to use actual pin values
- Combine multiple chipID reg values in a single define
(AD7173_AD4111_AD4112_AD4114_ID)
- Rename num_inputs and num_inputs_with_divider to include voltage
- Add comment to specify that num_voltage_inputs_with_divider does not
include the VCOM pin.
- Change break to direct returns where possible in switch cases
- Add fix for ad411x gpio's
iio: adc: ad7173: Reduce device info struct size
- Create patch
- Link to v1: https://lore.kernel.org/r/20240401-ad4111-v1-0-34618a9cc502@xxxxxxxxxx
---
Dumitru Ceclan (9):
dt-bindings: adc: ad7173: add support for ad411x
iio: adc: ad7173: fix buffers enablement for ad7176-2
iio: adc: ad7173: refactor channel configuration parsing
iio: adc: ad7173: refactor ain and vref selection
iio: adc: ad7173: add support for special inputs
iio: adc: ad7173: Add ad7173_device_info names
iio: adc: ad7173: Remove index from temp channel
iio: adc: ad7173: Add support for AD411x devices
iio: adc: ad7173: Reduce device info struct size
.../devicetree/bindings/iio/adc/adi,ad7173.yaml | 118 +++++-
drivers/iio/adc/ad7173.c | 438 ++++++++++++++++++---
2 files changed, 497 insertions(+), 59 deletions(-)
---
base-commit: 5ab61121a34759eb2418977f0b3589b7edc57776
change-id: 20240312-ad4111-7eeb34eb4a5f
Best regards,
--
Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>
