Re: [PATCH v2 2/2] arm64: dts: mediatek: Add mt7986 based Bananapi R3 Mini

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, May 09, 2024 at 05:21:57PM +0200, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
> 
> Add devicetree for Bananapi R3 Mini SBC.
> 
> Key features:
> - MediaTek MT7986A(Filogic 830) Quad core ARM Cortex A53
> - Wifi 6 2.4G/5G(MT7976C)
                  ^^       ^^
Those are full-width unicode parentheses.
Consider using normal 7-bit ASCII parentheses instead to keep the
commit message readable also on non-unicode terminals.

  Unicode    vs    ASCII
  ( 0xff08  vs    ( 0x28
  ) 0xff09  vs    ) 0x29


> - 2G DDR RAM
> - 8G eMMC flash
> - 128MB Nand flash
> - 2x 2.5GbE network port
> - 1x M.2 Key B USB interface
> - 1x M.2 KEY M PCIe interface
> - 1x USB2.0 interface
> 
> source: https://wiki.banana-pi.org/Banana_Pi_BPI-R3_Mini
> 
> Co-developed-by: Eric Woudstra <ericwouds@xxxxxxxxx>
> Signed-off-by: Eric Woudstra <ericwouds@xxxxxxxxx>
> Co-developed-by: Tianling Shen <cnsztl@xxxxxxxxx>
> Signed-off-by: Tianling Shen <cnsztl@xxxxxxxxx>
> Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>

Reviewed-by: Daniel Golle <daniel@xxxxxxxxxxxxxx>

> ---
> v2:
> - add missing node for nand
> - add some information about the board in description
> 
> change dts based on review from angelo+krzysztof
> 
> - drop fan status
> - rename phy14 to phy0 and phy15 to phy1
> - drop default-trigger from phys and so also the binding-patch
> - use regulator names based on regexp regulator-[0-9]+v[0-9]+
> - add comment for pwm
> ---
>  arch/arm64/boot/dts/mediatek/Makefile         |   1 +
>  .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 493 ++++++++++++++++++
>  2 files changed, 494 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 37b4ca3a87c9..1763b001ab06 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
> new file mode 100644
> index 000000000000..e2a2fea7adf0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
> @@ -0,0 +1,493 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Authors: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
> + *          Eric Woudstra <ericwouds@xxxxxxxxx>
> + *          Tianling Shen <cnsztl@xxxxxxxxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt65xx.h>
> +
> +#include "mt7986a.dtsi"
> +
> +/ {
> +	model = "Bananapi BPI-R3 Mini";
> +	chassis-type = "embedded";
> +	compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	dcin: regulator-12v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "12vd";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	fan: pwm-fan {
> +		compatible = "pwm-fan";
> +		#cooling-cells = <2>;
> +		/*
> +		 * The signal is inverted on this board and the PWM driver
> +		 * does not support polarity inversion.
> +		 */
> +		/* cooling level (0, 1, 2) */
> +		cooling-levels = <255 96 0>;
> +		pwms = <&pwm 0 10000>;
> +	};
> +
> +	reg_1p8v: regulator-1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1.8vd";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	reg_3p3v: regulator-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3.3vd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	usb_vbus: regulator-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpios = <&pio 20 GPIO_ACTIVE_LOW>;
> +		regulator-boot-on;
> +	};
> +
> +	en8811_a: regulator-phy1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "phy1";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&pio 16 GPIO_ACTIVE_LOW>;
> +		regulator-always-on;
> +	};
> +
> +	en8811_b: regulator-phy2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "phy2";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&pio 17 GPIO_ACTIVE_LOW>;
> +		regulator-always-on;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		green_led: led-0 {
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&pio 19 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		reset-key {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&pio 7 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +};
> +
> +&cpu_thermal {
> +	cooling-maps {
> +		map0 {
> +			/* active: set fan to cooling level 2 */
> +			cooling-device = <&fan 2 2>;
> +			trip = <&cpu_trip_active_high>;
> +		};
> +
> +		map1 {
> +			/* active: set fan to cooling level 1 */
> +			cooling-device = <&fan 1 1>;
> +			trip = <&cpu_trip_active_med>;
> +		};
> +
> +		map2 {
> +			/* active: set fan to cooling level 0 */
> +			cooling-device = <&fan 0 0>;
> +			trip = <&cpu_trip_active_low>;
> +		};
> +	};
> +};
> +
> +&crypto {
> +	status = "okay";
> +};
> +
> +&eth {
> +	status = "okay";
> +
> +	gmac0: mac@0 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <0>;
> +		phy-mode = "2500base-x";
> +		phy-handle = <&phy0>;
> +	};
> +
> +	gmac1: mac@1 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <1>;
> +		phy-mode = "2500base-x";
> +		phy-handle = <&phy1>;
> +	};
> +
> +	mdio: mdio-bus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default", "state_uhs";
> +	pinctrl-0 = <&mmc0_pins_default>;
> +	pinctrl-1 = <&mmc0_pins_uhs>;
> +	vmmc-supply = <&reg_3p3v>;
> +	vqmmc-supply = <&reg_1p8v>;
> +};
> +
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c_pins>;
> +	status = "okay";
> +
> +	/* MAC Address EEPROM */
> +	eeprom@50 {
> +		compatible = "atmel,24c02";
> +		reg = <0x50>;
> +
> +		address-width = <8>;
> +		pagesize = <8>;
> +		size = <256>;
> +	};
> +};
> +
> +&mdio {
> +	phy0: ethernet-phy@14 {
> +		reg = <14>;
> +		interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>;
> +		reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10000>;
> +		reset-deassert-us = <20000>;
> +		phy-mode = "2500base-x";
> +		full-duplex;
> +		pause;
> +		airoha,pnswap-rx;
> +
> +		leds {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			led@0 { /* en8811_a_gpio5 */
> +				reg = <0>;
> +				color = <LED_COLOR_ID_YELLOW>;
> +				function = LED_FUNCTION_LAN;
> +				function-enumerator = <1>;
> +				default-state = "keep";
> +			};
> +			led@1 { /* en8811_a_gpio4 */
> +				reg = <1>;
> +				color = <LED_COLOR_ID_GREEN>;
> +				function = LED_FUNCTION_LAN;
> +				function-enumerator = <2>;
> +				default-state = "keep";
> +			};
> +		};
> +	};
> +
> +	phy1: ethernet-phy@15 {
> +		reg = <15>;
> +		interrupts-extended = <&pio 46 IRQ_TYPE_EDGE_FALLING>;
> +		reset-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10000>;
> +		reset-deassert-us = <20000>;
> +		phy-mode = "2500base-x";
> +		full-duplex;
> +		pause;
> +		airoha,pnswap-rx;
> +
> +		leds {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			led@0 { /* en8811_b_gpio5 */
> +				reg = <0>;
> +				color = <LED_COLOR_ID_YELLOW>;
> +				function = LED_FUNCTION_WAN;
> +				function-enumerator = <1>;
> +				default-state = "keep";
> +			};
> +			led@1 { /* en8811_b_gpio4 */
> +				reg = <1>;
> +				color = <LED_COLOR_ID_GREEN>;
> +				function = LED_FUNCTION_WAN;
> +				function-enumerator = <2>;
> +				default-state = "keep";
> +			};
> +		};
> +	};
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_pins>;
> +	status = "okay";
> +};
> +
> +&pcie_phy {
> +	status = "okay";
> +};
> +
> +&pio {
> +	i2c_pins: i2c-pins {
> +		mux {
> +			function = "i2c";
> +			groups = "i2c";
> +		};
> +	};
> +
> +	mmc0_pins_default: mmc0-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	mmc0_pins_uhs: mmc0-uhs-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	pcie_pins: pcie-pins {
> +		mux {
> +			function = "pcie";
> +			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
> +		};
> +	};
> +
> +	pwm_pins: pwm-pins {
> +		mux {
> +			function = "pwm";
> +			groups = "pwm0";
> +		};
> +	};
> +
> +	spi_flash_pins: spi-flash-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi0", "spi0_wp_hold";
> +		};
> +	};
> +
> +	usb_ngff_pins: usb-ngff-pins {
> +		ngff-gnss-off-conf {
> +			pins = "GPIO_6";
> +			drive-strength = <8>;
> +			mediatek,pull-up-adv = <1>;
> +		};
> +		ngff-pe-rst-conf {
> +			pins = "GPIO_7";
> +			drive-strength = <8>;
> +			mediatek,pull-up-adv = <1>;
> +		};
> +		ngff-wwan-off-conf {
> +			pins = "GPIO_8";
> +			drive-strength = <8>;
> +			mediatek,pull-up-adv = <1>;
> +		};
> +		ngff-pwr-off-conf {
> +			pins = "GPIO_9";
> +			drive-strength = <8>;
> +			mediatek,pull-up-adv = <1>;
> +		};
> +		ngff-rst-conf {
> +			pins = "GPIO_10";
> +			drive-strength = <8>;
> +			mediatek,pull-up-adv = <1>;
> +		};
> +		ngff-coex-conf {
> +			pins = "SPI1_CS";
> +			drive-strength = <8>;
> +			mediatek,pull-up-adv = <1>;
> +		};
> +	};
> +
> +	wf_2g_5g_pins: wf-2g-5g-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_2g", "wf_5g";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_dbdc_pins: wf-dbdc-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_dbdc";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_led_pins: wf-led-pins {
> +		mux {
> +			function = "led";
> +			groups = "wifi_led";
> +		};
> +	};
> +};
> +
> +&pwm {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pwm_pins>;
> +	status = "okay";
> +};
> +
> +&spi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi_flash_pins>;
> +	status = "okay";
> +
> +	flash@0 {
> +		compatible = "spi-nand";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		reg = <0>;
> +
> +		spi-max-frequency = <20000000>;
> +		spi-tx-bus-width = <4>;
> +		spi-rx-bus-width = <4>;
> +	};
> +};
> +
> +&ssusb {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&usb_ngff_pins>;
> +	vusb33-supply = <&reg_3p3v>;
> +	vbus-supply = <&usb_vbus>;
> +	status = "okay";
> +};
> +
> +&trng {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&usb_phy {
> +	status = "okay";
> +};
> +
> +&watchdog {
> +	status = "okay";
> +};
> +
> +&wifi {
> +	status = "okay";
> +	pinctrl-names = "default", "dbdc";
> +	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
> +	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
> +
> +	led {
> +		led-active-low;
> +	};
> +};
> +
> -- 
> 2.34.1
> 
> 




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux