Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
---
.../boot/dts/ti/k3-j7200-common-proc-board.dts | 23 ++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 8 ++++++++
4 files changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 6593c5da82c0..f7b96e8d6462 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -129,6 +129,7 @@ J721E_WKUP_IOPAD(0x94, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
J721E_WKUP_IOPAD(0x8c, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
J721E_WKUP_IOPAD(0x88, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
>;
+ bootph-all;
};
wkup_uart0_pins_default: wkup-uart0-default-pins {
@@ -136,6 +137,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
J721E_WKUP_IOPAD(0x4c, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -153,12 +155,14 @@ J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>;
+ bootph-all;
};
wkup_gpio_pins_default: wkup-gpio-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x70, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_6 */
>;
+ bootph-all;
};
mcu_mdio_pins_default: mcu-mdio1-default-pins {
@@ -204,6 +208,7 @@ J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -238,6 +243,7 @@ J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
>;
+ bootph-all;
};
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
@@ -259,6 +265,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
pinctrl-single,pins = <
J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
+ bootph-all;
};
};
@@ -267,12 +274,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -281,6 +290,7 @@ &main_uart0 {
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
+ bootph-all;
};
&main_uart1 {
@@ -293,6 +303,7 @@ &main_uart1 {
&main_uart2 {
/* MAIN UART 2 is used by R5F firmware */
status = "reserved";
+ bootph-all; /* Doubtful if required or not */
};
&main_uart3 {
@@ -310,11 +321,13 @@ &wkup_gpio0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wkup_gpio_pins_default>;
+ bootph-all;
};
&mcu_cpsw {
pinctrl-names = "default";
pinctrl-0 = <&mcu_cpsw_pins_default>, <&mcu_mdio_pins_default>;
+ bootph-all;
};
&davinci_mdio {
@@ -341,6 +354,7 @@ exp1: gpio@20 {
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
+ bootph-all;
};
exp2: gpio@22 {
@@ -348,6 +362,7 @@ exp2: gpio@22 {
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
+ bootph-all;
};
};
@@ -381,6 +396,7 @@ &main_sdhci0 {
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&main_sdhci1 {
@@ -392,15 +408,18 @@ &main_sdhci1 {
vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&serdes_ln_ctrl {
idle-states = <J7200_SERDES0_LANE0_PCIE1_LANE0>, <J7200_SERDES0_LANE1_PCIE1_LANE1>,
<J7200_SERDES0_LANE2_QSGMII_LANE1>, <J7200_SERDES0_LANE3_IP4_UNUSED>;
+ bootph-all;
};
&usb_serdes_mux {
idle-states = <1>; /* USB0 to SERDES lane 3 */
+ bootph-all;
};
&usbss0 {
@@ -408,11 +427,13 @@ &usbss0 {
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
ti,usb2-only;
+ bootph-all;
};
&usb0 {
dr_mode = "otg";
maximum-speed = "high-speed";
+ bootph-all;
};
&tscadc0 {
@@ -432,6 +453,7 @@ serdes0_pcie_link: phy@0 {
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_PCIE>;
resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>;
+ bootph-all;
};
serdes0_qsgmii_link: phy@1 {
@@ -440,6 +462,7 @@ serdes0_qsgmii_link: phy@1 {
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_QSGMII>;
resets = <&serdes_wiz0 3>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 657f9cc9f4ea..111eba71ed33 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -136,6 +136,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: spinlock@30e00000 {
@@ -1538,5 +1539,6 @@ main_esm: esm@700000 {
compatible = "ti,j721e-esm";
reg = <0x0 0x700000 0x0 0x1000>;
ti,esm-pins = <656>, <657>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 7cf21c99956e..1e346451ee35 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -21,16 +21,19 @@ dmsc: system-controller@44083000 {
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -45,6 +48,7 @@ mcu_timer0: timer@40400000 {
assigned-clock-parents = <&k3_clks 35 2>;
power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
ti,timer-pwm;
+ bootph-pre-ram;
};
mcu_timer1: timer@40410000 {
@@ -187,6 +191,7 @@ wkup_conf: bus@43000000 {
chipid: chipid@14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -347,6 +352,7 @@ mcu_ringacc: ringacc@2b800000 {
ti,sci = <&dmsc>;
ti,sci-dev-id = <235>;
msi-parent = <&main_udmass_inta>;
+ bootph-all;
};
mcu_udmap: dma-controller@285c0000 {
@@ -371,6 +377,7 @@ mcu_udmap: dma-controller@285c0000 {
ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
<0x0b>; /* RX_HCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ bootph-all;
};
};
@@ -387,6 +394,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
@@ -530,6 +538,7 @@ hbmc_mux: mux-controller@47000004 {
reg = <0x00 0x47000004 0x00 0x4>;
#mux-control-cells = <1>;
mux-reg-masks = <0x0 0x2>; /* HBMC select */
+ bootph-all;
};
hbmc: hyperbus@47034000 {
@@ -648,6 +657,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x42050000 0x00 0x350>;
power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
#thermal-sensor-cells = <1>;
+ bootph-all;
};
mcu_esm: esm@40800000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 7e6a584ac6f0..a875a79e95c6 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -15,6 +15,7 @@ memory@80000000 {
/* 4G RAM */
reg = <0x00 0x80000000 0x00 0x80000000>,
<0x08 0x80000000 0x00 0x80000000>;
+ bootph-all;
};
reserved_memory: reserved-memory {
@@ -120,6 +121,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
>;
+ bootph-all;
};
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
@@ -136,6 +138,7 @@ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */
>;
+ bootph-all;
};
};
@@ -145,6 +148,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
};
@@ -162,6 +166,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>;
+ bootph-all;
};
main_mcan0_pins_default: main-mcan0-default-pins {
@@ -185,6 +190,7 @@ &hbmc {
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
reg = <0x00 0x00 0x4000000>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -329,6 +335,7 @@ bucka1: buck1 {
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
+ bootph-all;
};
bucka2: buck2 {
@@ -463,6 +470,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <4>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
--
2.43.2
