On Sat, 04 May 2024, André Apitzsch wrote:
> Am Freitag, dem 03.05.2024 um 08:19 +0100 schrieb Lee Jones:
> > On Thu, 11 Apr 2024, Lee Jones wrote:
> >
> > > On Mon, 01 Apr 2024, André Apitzsch via B4 Relay wrote:
> > >
> > > > From: André Apitzsch <git@xxxxxxxxxxx>
> > > >
> > > > Add support for SY7802 flash LED controller. It can support up to
> > > > 1.8A
> > > > flash current.
> > >
> > > This is a very small commit message for a 500+ line change!
> > >
> > > Please, tell us more.
> > >
> > > > Signed-off-by: André Apitzsch <git@xxxxxxxxxxx>
> > > > ---
> > > > drivers/leds/flash/Kconfig | 11 +
> > > > drivers/leds/flash/Makefile | 1 +
> > > > drivers/leds/flash/leds-sy7802.c | 532
> > > > +++++++++++++++++++++++++++++++++++++++
> > > > 3 files changed, 544 insertions(+)
> > > >
> > > > diff --git a/drivers/leds/flash/Kconfig
> > > > b/drivers/leds/flash/Kconfig
> > > > index 809b6d98bb3e..f39f0bfe6eef 100644
> > > > --- a/drivers/leds/flash/Kconfig
> > > > +++ b/drivers/leds/flash/Kconfig
> > > > @@ -121,4 +121,15 @@ config LEDS_SGM3140
> > > > This option enables support for the SGM3140 500mA
> > > > Buck/Boost Charge
> > > > Pump LED Driver.
> > > >
> > > > +config LEDS_SY7802
> > > > + tristate "LED support for the Silergy SY7802"
> > > > + depends on I2C && OF
> > > > + depends on GPIOLIB
> > > > + select REGMAP_I2C
> > > > + help
> > > > + This option enables support for the SY7802 flash LED
> > > > controller.
> > > > + SY7802 includes torch and flash functions with
> > > > programmable current.
> > > > +
> > > > + This driver can be built as a module, it will be
> > > > called "leds-sy7802".
> > > > +
> > > > endif # LEDS_CLASS_FLASH
> > > > diff --git a/drivers/leds/flash/Makefile
> > > > b/drivers/leds/flash/Makefile
> > > > index 91d60a4b7952..48860eeced79 100644
> > > > --- a/drivers/leds/flash/Makefile
> > > > +++ b/drivers/leds/flash/Makefile
> > > > @@ -11,3 +11,4 @@ obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-
> > > > flash.o
> > > > obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o
> > > > obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o
> > > > obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o
> > > > +obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o
> > > > diff --git a/drivers/leds/flash/leds-sy7802.c
> > > > b/drivers/leds/flash/leds-sy7802.c
> > > > new file mode 100644
> > > > index 000000000000..c03a571b0e08
> > > > --- /dev/null
> > > > +++ b/drivers/leds/flash/leds-sy7802.c
> > > > @@ -0,0 +1,532 @@
> >
> > [...]
> >
> > > > +static int sy7802_torch_brightness_set(struct led_classdev
> > > > *lcdev, enum led_brightness level)
> > >
> > > s/level/brightness/
> > >
> > > > +{
> > > > + struct sy7802_led *led = container_of(lcdev, struct
> > > > sy7802_led, flash.led_cdev);
> > > > + u32 led_enable_mask = led->led_no == SY7802_LED_JOINT ?
> > > > SY7802_LEDS_MASK_ALL :
> > > > + SY7802_LEDS_MASK(led->led_no);
> > >
> > > Do all of the fancy multi-line assignment outside of the
> > > declaration block.
> > >
> > > > + u32 enable_mask = SY7802_MODE_MASK | led_enable_mask;
> > > > + u32 val = level ? led_enable_mask : SY7802_MODE_OFF;
> > > > + struct sy7802 *chip = led->chip;
> > > > + u32 curr;
> > >
> > > This is a temporary placeholder for fled_torch_used, right?
> > >
> > > fled_torch_used_tmp? Sometimes abbreviated to tmp.
> > >
> > > > + u32 mask;
> > >
> > > That's a lot of masks. Which one is this?
> > >
> > > > + int ret;
> > > > +
> > > > + mutex_lock(&chip->mutex);
> > > > +
> > > > + /*
> > > > + * There is only one set of flash control logic, and
> > > > this flag is used to check if 'strobe'
> > >
> > > The ',' before 'and' is superfluous.
> > >
> > > > + * is currently being used.
> > > > + */
> > >
> > > Doesn't the variable name kind of imply this?
> > >
> > > > + if (chip->fled_strobe_used) {
> > > > + dev_warn(chip->dev, "Please disable strobe first
> > > > [%d]\n", chip->fled_strobe_used);
> > >
> > > "Cannot set torch brightness whilst strobe is enabled"
> > >
> > > > + ret = -EBUSY;
> > > > + goto unlock;
> > > > + }
> > > > +
> > > > + if (level)
> > > > + curr = chip->fled_torch_used | BIT(led->led_no);
> > > > + else
> > > > + curr = chip->fled_torch_used & ~BIT(led-
> > > > >led_no);
> > > > +
> > > > + if (curr)
> > > > + val |= SY7802_MODE_TORCH;
> > > > +
> > > > + /* Torch needs to be disabled first to apply new
> > > > brightness */
> > >
> > > "Disable touch to apply brightness"
> > >
> > > > + ret = regmap_update_bits(chip->regmap,
> > > > SY7802_REG_ENABLE, SY7802_MODE_MASK,
> > > > + SY7802_MODE_OFF);
> > > > + if (ret)
> > > > + goto unlock;
> > > > +
> > > > + mask = led->led_no == SY7802_LED_JOINT ?
> > > > SY7802_TORCH_CURRENT_MASK_ALL :
> > >
> > > Why not just use led->led_no in place of mask?
> >
> > mask and led->led_no are assigned the same value from this point on.
>
> Thanks for the clarification.
> How to you come to the conclusion that mask and led->led_no are
> assigned the same value from this point on?
Because I am blind and didn't see the double equals ("==").
#shouldhavegonetospecsavers
--
Lee Jones [李琼斯]
