On 20/02/15 17:21, Rob Herring wrote:
On Thu, Feb 19, 2015 at 11:08 AM, Srinivas Kandagatla
<srinivas.kandagatla@xxxxxxxxxx> wrote:
From: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
Up until now, EEPROM drivers were stored in drivers/misc, where they all had to
duplicate pretty much the same code to register a sysfs file, allow in-kernel
users to access the content of the devices they were driving, etc.
This was also a problem as far as other in-kernel users were involved, since
the solutions used were pretty much different from on driver to another, there
was a rather big abstraction leak.
This introduction of this framework aims at solving this. It also introduces DT
representation for consumer devices to go get the data they require (MAC
Addresses, SoC/Revision ID, part numbers, and so on) from the EEPROMs.
Having regmap interface to this framework would give much better
abstraction for eeproms on different buses.
Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
[srinivas.kandagatla: Moved to regmap based and cleanedup apis]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
---
.../devicetree/bindings/eeprom/eeprom.txt | 48 ++++
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/eeprom/Kconfig | 19 ++
drivers/eeprom/Makefile | 9 +
drivers/eeprom/core.c | 290 +++++++++++++++++++++
include/linux/eeprom-consumer.h | 73 ++++++
include/linux/eeprom-provider.h | 51 ++++
Who is going to be the maintainer for this?
Am happy to be one.
8 files changed, 493 insertions(+)
create mode 100644 Documentation/devicetree/bindings/eeprom/eeprom.txt
create mode 100644 drivers/eeprom/Kconfig
create mode 100644 drivers/eeprom/Makefile
create mode 100644 drivers/eeprom/core.c
create mode 100644 include/linux/eeprom-consumer.h
create mode 100644 include/linux/eeprom-provider.h
diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt
new file mode 100644
index 0000000..9ec1ec2
--- /dev/null
+++ b/Documentation/devicetree/bindings/eeprom/eeprom.txt
Please make bindings a separate patch.
Sure, Will do it in next version.
@@ -0,0 +1,48 @@
+= EEPROM Data Device Tree Bindings =
+
+This binding is intended to represent the location of hardware
+configuration data stored in EEPROMs.
+
+On a significant proportion of boards, the manufacturer has stored
+some data on an EEPROM-like device, for the OS to be able to retrieve
+these information and act upon it. Obviously, the OS has to know
+about where to retrieve these data from, and where they are stored on
+the storage device.
+
+This document is here to document this.
+
+= Data providers =
+
+Required properties:
+#eeprom-cells: Number of cells in an eeprom specifier; The common
+ case is 2.
We already have eeproms in DTs, it would be nice to be able to support
them with this framework as well.
Yes, I can see more than 60% of them are atmel,at24* eeproms in DT. We
have some plans to migrate at24 and at25 eeproms to this framework once
the the framework itself is accepted.
+
+For example:
+
+ at24: eeprom@42 {
+ #eeprom-cells = <2>;
+ };
+
+= Data consumers =
+
+Required properties:
+
+eeproms: List of phandle and data cell specifier triplet, one triplet
+ for each data cell the device might be interested in. The
+ triplet consists of the phandle to the eeprom provider, then
+ the offset in byte within that storage device, and the length
+ in byte of the data we care about.
The problem with this is it assumes you know who the consumer is and
that it is a DT node. For example, how would you describe a serial
number?
Correct me if I miss understood.
Is serial number any different?
Am hoping that the eeprom consumer would be aware of offset and size of
serial number in the eeprom
Cant the consumer do:
eeprom-consumer {
eeproms = <&at24 0 4>;
eeprom-names = "device-serial-number";
};
--srini
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
