ARM SCMI v3.2 Table 24 Pin Configuration Type and Enumerations:
'192 -255 OEM specific units'.
i.MX95 System Manager FW supports SCMI PINCTRL protocol, but it has zero
functions, groups. So pinctrl-scmi.c could not be reused for i.MX95.
Because nxp,pin-func, nxp,pin-conf properties are rejected by dt
maintainers, so use generic property 'pinmux' which requires a new driver
pinctrl-imx-scmi.c
The node will be as below:
pinctrl_usdhc1: usdhc1-pins {
sd1-grp0 {
pinmux = <IMX95_PAD_SD1_CLK__USDHC1_CLK
IMX95_PAD_SD1_STROBE__USDHC1_STROBE>;
drive-strength = <0xe>;
input-schmitt-enable;
bias-pull-down;
slew-rate = <0x3>;
};
sd1-grp1 {
pinmux = <IMX95_PAD_SD1_CMD__USDHC1_CMD
IMX95_PAD_SD1_DATA0__USDHC1_DATA0
IMX95_PAD_SD1_DATA1__USDHC1_DATA1
IMX95_PAD_SD1_DATA2__USDHC1_DATA2
IMX95_PAD_SD1_DATA3__USDHC1_DATA3
IMX95_PAD_SD1_DATA4__USDHC1_DATA4
IMX95_PAD_SD1_DATA5__USDHC1_DATA5
IMX95_PAD_SD1_DATA6__USDHC1_DATA6
IMX95_PAD_SD1_DATA7__USDHC1_DATA7>;
drive-strength = <0xe>;
input-schmitt-enable;
bias-pull-up;
slew-rate = <0x3>;
};
};
Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
---
Changes in v4:
- Rebase to next-20240503
- Add pinctrl-scmi-imx.c itself get pins and scmi pinctrl structure to decouple
pinctrl-scmi.c and pinctrl-scmi-imx.c, so drop patch 3,4,5.
- Link to v3: https://lore.kernel.org/r/20240428-pinctrl-scmi-oem-v3-v3-0-eda341eb47ed@xxxxxxx
Changes in v3:
- patch 2,3,4,5 are new.
- Rewrite the binding, drop nxp,pin-x properties, use generic properties
as Rob commented.
- Switch to using pinmux means pinctrl-scmi.c could not be reused, so
add a new driver in patch 6 for i.MX95. But pinctrl_scmi_get_pins and
scmi_pinctrl are exported for i.MX95 usage.
- Link to v2: https://lore.kernel.org/r/20240418-pinctrl-scmi-oem-v1-v2-0-3a555a3c58c3@xxxxxxx
Changes in v2:
- Rename nxp,imx95-pinctrl.yaml to nxp,imx95-scmi-pinctrl.yaml and move
to firmware
- Merged patch [1,2]/3 v1 into patch 1/2 v2.
- nxp,imx95-scmi-pinctrl.yaml only has patterProperties for subnode
The pinctrl will be as below for i.MX95.
pinctrl_usdhc1: usdhc1-pins {
sd1cmd {
pins = "sd1cmd";
nxp,func-id = <0>;
nxp,pin-conf = <0x138e>;
};
sd1data {
pins = "sd1data";
nxp,func-id = <0>;
nxp,pin-conf = <0x138e>;
};
};
- Add pins enum, correct description.
- Link to v1: https://lore.kernel.org/r/20240412-pinctrl-scmi-oem-v1-v1-0-704f242544c1@xxxxxxx
---
Peng Fan (3):
dt-bindings: firmware: arm,scmi: Add properties for i.MX95 Pinctrl OEM extensions
pinctrl: scmi: add blocklist
pinctrl: imx: support SCMI pinctrl protocol for i.MX95
.../devicetree/bindings/firmware/arm,scmi.yaml | 9 +-
.../bindings/firmware/nxp,imx95-scmi-pinctrl.yaml | 37 ++
drivers/pinctrl/freescale/Kconfig | 9 +
drivers/pinctrl/freescale/Makefile | 1 +
drivers/pinctrl/freescale/pinctrl-imx-scmi.c | 586 +++++++++++++++++++++
drivers/pinctrl/pinctrl-scmi.c | 10 +
6 files changed, 649 insertions(+), 3 deletions(-)
---
base-commit: 4db57327adc359a3f9a3481d60104be67c42964f
change-id: 20240428-pinctrl-scmi-oem-v3-12130031a74d
Best regards,
--
Peng Fan <peng.fan@xxxxxxx>
