Dne petek, 26. april 2024 ob 11:51:40 GMT +2 je Ryan Walklin napisal(a): > The base model RG35XX (2024) is a handheld gaming device based on an Allwinner H700 chip. > > The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31 GPU) which exposes RGB LCD and NMI pins. > > Device features: > - Allwinner H700 @ 1.5GHz > - 1GB LPDDR4 DRAM > - X-Powers AXP717 PMIC > - 3.5" 640x480 RGB LCD > - Two microSD slots > - Mini-HDMI out > - GPIO keypad > - 3.5mm headphone jack > - USB-C charging port > > Enabled in this DTS: > - AXP717 PMIC with RSB serial interface, regulators and NMI interrupt controller > - Power LED (charge LED on device controlled directly by PMIC) > - Serial UART (accessible from headers on the board) > - MMC slots > > Signed-off-by: Ryan Walklin <ryan@xxxxxxxxxxxxx> > --- > Changelog v1..v2: > - Update copyright > - Spaces -> Tabs > - Add cpufreq support > - Remove MMC aliases > - Fix GPIO button and regulator node names > - Note unused AXP717 regulators > - Update regulators for SD slots > - Remove unused I2C3 device > - Update NMI interrupt controller for AXP717, requires H616 support patch in dt-next [1] > - Add chassis-type > - Address USB EHCI/OHCI0 correctly and add usb vbus supply > - Add PIO vcc-pg-supply > - Correct boost regulator voltage and name > > Changelog v2..v3: > - Remove cpufreq support (patch still pending for 6.10, will followup with enablement patch once opp table merged) > - Add dtb to Makefile > - Remove unnecessary duplicated PLL regulator > - Remove unimplemented/not-present drive-vbus feature from AXP717 > - Rename CLDO3 to "vcc-io", inferring function from board testing by Chris Morgan > - Correct MMC1 vmmc-supply to CLDO3 and MMC2 to CLDO4 > - Reduce DCDC1 "vdd-cpu" supply voltage range to 0.9v-1.1v to match lowest OPP voltage > - Identify DCDC2 as GPU supply - rename to "vdd-gpu-sys", remove always-on and use fixed 0.94v voltage > - Fix indentation > - Correct boot/always-on states and voltages for various regulators from vendor BSP > - Change USB-OTG mode to "peripheral" and correct comment > - Correct and add remaining PIO supplies > - Move volume key GPIOs to separate block to allow key repeat > - Alphabetically orrder gamepad GPIOs > - Move changelog and links below fold-line > - Remove USB 3.3v VCC-USB and VCC-SD2 regulators pending further hardware investigation (to be submitted as subsequent patch) > - Constrain boost regulator voltage to 5.0v to 5.2v to capture default voltage of 5.126v > > Changelog v3..v4: > - Cluster USB nodes > - Do not define voltage range for currently unused CLDO1 (connected to audio codec according to vendor BSP - driver not yet implemented) and ALDO3 (1.8v). > - Note voltages set for currently unused regulators from vendor BSP in comments to aid identification > - Remove regulator-boot-on from several regulators where it was not required > - Fix indentation > - Add "disable-wp" for SD2 as for SD1 (doesn't make sense for micro-SD) > - Restore fixed 3.3v regulator for SD2 (vcc_3v3_sd2), which is required for SD2 to function. CLDO4 appears to be the 1.8v supply required for low-voltage UHS-I signalling, however a GPIO pin to switch between the supplies is not yet confirmed (likely PE4) and will be implemented in a subsequent patch. > > [1]: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=d47bca77bf3ab475c33b3929c33c80aeb49df35c > > Signed-off-by: Ryan Walklin <ryan@xxxxxxxxxxxxx> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../sun50i-h700-anbernic-rg35xx-2024.dts | 347 ++++++++++++++++++ > 2 files changed, 348 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index 21149b346a60..6f997157968e 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -47,3 +47,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts > new file mode 100644 > index 000000000000..112605561e92 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts <snip> > + > +&r_rsb { > + status = "okay"; > + > + axp717: pmic@3a3 { > + compatible = "x-powers,axp717"; > + reg = <0x3a3>; > + interrupt-controller; > + #interrupt-cells = <1>; > + interrupt-parent = <&nmi_intc>; > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + > + vin1-supply = <®_vcc5v>; > + vin2-supply = <®_vcc5v>; > + vin3-supply = <®_vcc5v>; > + vin4-supply = <®_vcc5v>; > + > + regulators { > + reg_dcdc1: dcdc1 { > + regulator-always-on; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdc2: dcdc2 { > + regulator-always-on; > + regulator-min-microvolt = <940000>; > + regulator-max-microvolt = <940000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdc3: dcdc3 { > + regulator-always-on; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-dram"; > + }; > + > + reg_aldo1: aldo1 { /* SDC2 */ > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-sd2"; > + }; > + > + reg_aldo2: aldo2 { > + /* 1.8v - unused */ > + }; > + > + reg_aldo3: aldo3 { > + /* 1.8v - unused */ > + }; > + > + reg_aldo4: aldo4 { /* 5096000.codec */ Above comment doesn't make any sense. Remove it. Best regards, Jernej > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-pg"; > + }; > + > + reg_bldo1: bldo1 { > + /* 1.8v - unused */ > + }; > + > + reg_bldo2: bldo2 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-pll"; > + }; > + > + reg_bldo3: bldo3 { > + /* 2.8v - unused */ > + }; > + > + reg_bldo4: bldo4 { > + /* 1.2v - unused */ > + }; > + > + reg_cldo1: cldo1 { > + /* 3.3v - audio codec - not yet implemented */ > + }; > + > + reg_cldo2: cldo2 { > + /* 3.3v - unused */ > + }; > + > + reg_cldo3: cldo3 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-io"; > + }; > + > + reg_cldo4: cldo4 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-wifi"; > + }; > + > + reg_boost: boost { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5200000>; > + regulator-name = "boost"; > + }; > + > + reg_cpusldo: cpusldo { > + /* unused */ > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&pio { > + vcc-pa-supply = <®_cldo3>; > + vcc-pc-supply = <®_cldo3>; > + vcc-pe-supply = <®_cldo3>; > + vcc-pf-supply = <®_cldo3>; > + vcc-pg-supply = <®_aldo4>; > + vcc-ph-supply = <®_cldo3>; > + vcc-pi-supply = <®_cldo3>; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +/* the AXP717 has USB type-C role switch functionality, not yet described by the binding */ > +&usbotg { > + dr_mode = "peripheral"; /* USB type-C receptable */ > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +}; >
