Il 22/04/24 11:39, Macpaul Lin ha scritto:
1. Add i2c to aliases.
2. Add MUX IT5205 support to i2c1.
3. Add TYPEC RT1715 support to i2c4.
4. Add PMIC_KEY setting.
5. Add USB HUB TUSB8020 to xhci1.
Signed-off-by: Macpaul Lin <macpaul.lin@xxxxxxxxxxxx>
---
.../dts/mediatek/mt8390-genio-700-evk.dts | 56 ++++++++++++++++++-
1 file changed, 55 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
index 9b7ad046f193..17f22b1836bf 100644
--- a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
@@ -23,6 +23,15 @@
"mediatek,mt8188";
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ mmc0 = &mmc0;
+ mmc1 = &mmc1;
serial0 = &uart0;
};
@@ -225,6 +234,16 @@
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
status = "okay";
+
+ typec-mux@48 {
+ compatible = "ite,it5205";
+ reg = <0x48>;
+
+ mode-switch;
+ orientation-switch;
+
+ vcc-supply = <&mt6359_vcn33_1_bt_ldo_reg>;
+ };
};
&i2c2 {
@@ -242,11 +261,19 @@
};
&i2c4 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "default";
pinctrl-0 = <&i2c4_pins>;
pinctrl-1 = <&rt1715_int_pins>;
This should be
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins>;
clock-frequency = <1000000>;
status = "okay";
+
+ rt1715@4e {
+ compatible = "richtek,rt1715";
+ reg = <0x4e>;
+ interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&usb_p1_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&rt1715_int_pins>;
Cheers,
Angelo
+ status = "okay";
+ };
};
&i2c5 {
@@ -836,6 +863,17 @@
&pmic {
interrupt-parent = <&pio>;
interrupts = <222 IRQ_TYPE_LEVEL_HIGH>;
+
+ mt6359keys: keys {
+ compatible = "mediatek,mt6359-keys";
+ mediatek,long-press-mode = <1>;
+ power-off-time-sec = <0>;
+
+ power-key {
+ linux,keycodes = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
};
&scp {
@@ -890,6 +928,22 @@
&xhci1 {
status = "okay";
vusb33-supply = <&mt6359_vusb_ldo_reg>;
+
+ hub_2_0: hub@1 {
+ compatible = "usb451,8025";
+ reg = <1>;
+ peer-hub = <&hub_3_0>;
+ reset-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+ vdd-supply = <&usb_hub_fixed_3v3>;
+ };
+
+ hub_3_0: hub@2 {
+ compatible = "usb451,8027";
+ reg = <2>;
+ peer-hub = <&hub_2_0>;
+ reset-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+ vdd-supply = <&usb_hub_fixed_3v3>;
+ };
};
&xhci2 {
