Re: [PATCH 2/2] arm64: dts: rockchip: Add Radxa ROCK3 Model C

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Chukun,

On 2024-04-16 15:00, Chukun Pan wrote:
> The Radxa ROCK3 Model C is a development board with the
> Rockchip RK3566 SoC. It has the following features:
> 
> - 1/2/4GB LPDDR4
> - 1x HDMI Type A
> - 1x PCIE 2.0 slot
> - 1x FAN connector
> - 3.5mm jack with mic
> - 1GbE RTL8211F Ethernet
> - 1x USB 3.0, 3x USB 2.0
> - 40-pin expansion header
> - MicroSD card/eMMC socket
> - 16MB SPI NOR (gd25lq128d)

Great, I was about to send out a similar device tree patch for this
board, below you find a few remarks.

> 
> Signed-off-by: Chukun Pan <amadeus@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../boot/dts/rockchip/rk3566-rock-3c.dts      | 751 ++++++++++++++++++
>  2 files changed, 752 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-rock-3c.dts
> 
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 0192980ef37f..53efff815bf3 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -90,6 +90,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-b.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-radxa-cm3-io.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-roc-pc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-rock-3c.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-blade.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-model-a.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-rock-3c.dts b/arch/arm64/boot/dts/rockchip/rk3566-rock-3c.dts
> new file mode 100644
> index 000000000000..96d24069aba2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-rock-3c.dts
> @@ -0,0 +1,751 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> +	model = "Radxa ROCK3 Model C";

The marketing name seems to be "Radxa ROCK 3C" according to the product
page at [1].

[1] https://radxa.com/products/rock3/3c

> +	compatible = "radxa,rock3c", "rockchip,rk3566";

A personal preference would be to match the product name and the dtb
filename, e.g. "radxa,rock-3c".

> +
> +	aliases {
> +		ethernet0 = &gmac1;
> +		mmc0 = &sdhci;
> +		mmc1 = &sdmmc0;
> +		mmc2 = &sdmmc1;
> +	};
> +
> +	chosen: chosen {
> +		stdout-path = "serial2:1500000n8";
> +	};
> +
> +	hdmi-con {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	gmac1_clkin: external-gmac1-clock {
> +		compatible = "fixed-clock";
> +		clock-frequency = <125000000>;
> +		clock-output-names = "gmac1_clkin";
> +		#clock-cells = <0>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led_user: led-0 {

This is called user_led2 in the schematic, in case we want the symbol to
match the schematic.

> +			gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
> +			function = LED_FUNCTION_HEARTBEAT;
> +			color = <LED_COLOR_ID_BLUE>;
> +			linux,default-trigger = "heartbeat";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&led_user_en>;
> +		};
> +	};
> +
> +	rk809-sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,format = "i2s";
> +		simple-audio-card,name = "Analog RK809";
> +		simple-audio-card,mclk-fs = <256>;
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&i2s1_8ch>;
> +		};
> +
> +		simple-audio-card,codec {
> +			sound-dai = <&rk809>;
> +		};
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		clocks = <&rk809 1>;
> +		clock-names = "ext_clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_reg_on_h>;
> +		post-power-on-delay-ms = <100>;
> +		power-off-delay-us = <5000000>;
> +		reset-gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	vcc5v_dcin: vcc5v-dcin-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v_dcin";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc3v3_pcie: vcc3v3-pcie-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pcie_pwr_en>;
> +		regulator-name = "vcc3v3_pcie";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc3v3_sys>;
> +	};
> +
> +	vcc3v3_sys: vcc3v3-sys-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc5v0_sys: vcc5v0-sys-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc5v_dcin>;
> +	};
> +
> +	vcc5v0_usb_host: vcc5v0-usb-host-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc5v0_usb_host_en>;
> +		regulator-name = "vcc5v0_usb_host";

This regulator is named vcc5v0_usb30_host in schematic.

> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc5v0_usb_otg_en>;
> +		regulator-name = "vcc5v0_usb_otg";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc_cam: vcc-cam-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc_cam_en>;
> +		regulator-name = "vcc_cam";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc3v3_sys>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	vcc_mipi: vcc-mipi-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc_mipi_en>;
> +		regulator-name = "vcc_mipi";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc3v3_sys>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +};
> +
> +&combphy1 {
> +	status = "okay";
> +};
> +
> +&combphy2 {
> +	status = "okay";
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&gmac1 {
> +	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
> +	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&gmac1_clkin>;
> +	clock_in_out = "input";
> +	phy-handle = <&rgmii_phy1>;
> +	phy-mode = "rgmii-id";
> +	phy-supply = <&vcc_3v3>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac1m1_miim
> +		     &gmac1m1_tx_bus2
> +		     &gmac1m1_rx_bus2
> +		     &gmac1m1_rgmii_clk
> +		     &gmac1m1_clkinout
> +		     &gmac1m1_rgmii_bus>;
> +	status = "okay";
> +};
> +
> +&gpu {
> +	mali-supply = <&vdd_gpu>;
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	avdd-0v9-supply = <&vdda0v9_image>;
> +	avdd-1v8-supply = <&vcca1v8_image>;
> +	status = "okay";
> +};
> +
> +&hdmi_in {
> +	hdmi_in_vp0: endpoint {
> +		remote-endpoint = <&vp0_out_hdmi>;
> +	};
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +&hdmi_sound {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	vdd_cpu: regulator@1c {
> +		compatible = "tcs,tcs4525";
> +		reg = <0x1c>;
> +		fcs,suspend-voltage-selector = <1>;
> +		regulator-name = "vdd_cpu";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <800000>;
> +		regulator-max-microvolt = <1150000>;
> +		regulator-ramp-delay = <2300>;
> +		vin-supply = <&vcc5v0_sys>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	rk809: pmic@20 {
> +		compatible = "rockchip,rk809";
> +		reg = <0x20>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> +		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> +		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> +		#clock-cells = <1>;
> +		clock-names = "mclk";
> +		clocks = <&cru I2S1_MCLKOUT_TX>;

I think clock-output-names may be missing? Something like:

  clock-output-names = "rk809-clkout1", "rk809-clkout2";

> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
> +		rockchip,system-power-controller;

I think this prop is deprecated and system-power-controller should be
used instead.

> +		#sound-dai-cells = <0>;
> +		vcc1-supply = <&vcc3v3_sys>;
> +		vcc2-supply = <&vcc3v3_sys>;
> +		vcc3-supply = <&vcc3v3_sys>;
> +		vcc4-supply = <&vcc3v3_sys>;
> +		vcc5-supply = <&vcc3v3_sys>;
> +		vcc6-supply = <&vcc3v3_sys>;
> +		vcc7-supply = <&vcc3v3_sys>;
> +		vcc8-supply = <&vcc3v3_sys>;
> +		vcc9-supply = <&vcc3v3_sys>;
> +		wakeup-source;
> +
> +		regulators {
> +			vdd_logic: DCDC_REG1 {
> +				regulator-name = "vdd_logic";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-initial-mode = <0x2>;
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <900000>;

Not sure we need this in suspend to ram and this can probably use:

  regulator-off-in-suspend

That is also what vendor kernel does.

> +				};
> +			};
> +
> +			vdd_gpu: DCDC_REG2 {
> +				regulator-name = "vdd_gpu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-initial-mode = <0x2>;
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +					regulator-suspend-microvolt = <900000>;
> +				};
> +			};
> +
> +			vcc_ddr: DCDC_REG3 {
> +				regulator-name = "vcc_ddr";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-initial-mode = <0x2>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vdd_npu: DCDC_REG4 {
> +				regulator-name = "vdd_npu";
> +				regulator-initial-mode = <0x2>;
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_1v8: DCDC_REG5 {
> +				regulator-name = "vcc_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda0v9_image: LDO_REG1 {
> +				regulator-name = "vdda0v9_image";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda_0v9: LDO_REG2 {
> +				regulator-name = "vdda_0v9";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda0v9_pmu: LDO_REG3 {
> +				regulator-name = "vdda0v9_pmu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <900000>;
> +				};
> +			};
> +
> +			vccio_acodec: LDO_REG4 {
> +				regulator-name = "vccio_acodec";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG5 {
> +				regulator-name = "vccio_sd";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_pmu: LDO_REG6 {
> +				regulator-name = "vcc3v3_pmu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vcca_1v8: LDO_REG7 {
> +				regulator-name = "vcca_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca1v8_pmu: LDO_REG8 {
> +				regulator-name = "vcca1v8_pmu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcca1v8_image: LDO_REG9 {
> +				regulator-name = "vcca1v8_image";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_3v3: SWITCH_REG1 {
> +				regulator-name = "vcc_3v3";
> +				regulator-always-on;
> +				regulator-boot-on;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_sd: SWITCH_REG2 {
> +				regulator-name = "vcc3v3_sd";
> +				regulator-always-on;
> +				regulator-boot-on;

If I am reading the schematic correctly this is not connected.

> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +		};
> +
> +		codec {
> +			mic-in-differential;
> +		};
> +	};
> +
> +	eeprom: eeprom@50 {
> +		compatible = "belling,bl24c16a", "atmel,24c16";
> +		reg = <0x50>;
> +		pagesize = <16>;
> +	};
> +};
> +
> +&i2s0_8ch {
> +	status = "okay";
> +};
> +
> +&i2s1_8ch {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_lrcktx &i2s1m0_sdi0 &i2s1m0_sdo0>;
> +	rockchip,trcm-sync-tx-only;
> +	status = "okay";
> +};
> +
> +&mdio1 {
> +	rgmii_phy1: ethernet-phy@1 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0x1>;
> +		reset-assert-us = <20000>;
> +		reset-deassert-us = <100000>;
> +		reset-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +&pcie2x1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_reset_h>;
> +	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
> +	vpcie3v3-supply = <&vcc3v3_pcie>;
> +	status = "okay";
> +};
> +
> +&pinctrl {
> +	bluetooth {
> +		bt_reg_on_h: bt-reg-on-h {
> +			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		bt_wake_host_h: bt-wake-host-h {
> +			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		bt_host_wake_h: bt-host-wake-h {
> +			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	cam {
> +		vcc_cam_en: vcc_cam_en {
> +			rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	display {
> +		vcc_mipi_en: vcc_mipi_en {
> +			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	leds {
> +		led_user_en: led_user_en {
> +			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pcie {
> +		pcie_pwr_en: pcie-pwr-en {
> +			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		pcie_reset_h: pcie-reset-h {
> +			rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pmic {
> +		pmic_int_l: pmic-int-l {
> +			rockchip,pins =	<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;

This should probably use a space instead of a tab after =.

> +		};
> +	};
> +
> +	usb {
> +		vcc5v0_usb_host_en: vcc5v0-usb-host-en {
> +			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		vcc5v0_usb_otg_en: vcc5v0-usb-otg-en {
> +			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	wifi {
> +		wifi_host_wake_h: wifi-host-wake-h {
> +			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		wifi_reg_on_h: wifi-reg-on-h {
> +			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +};
> +
> +&pmu_io_domains {
> +	pmuio1-supply = <&vcc3v3_pmu>;
> +	pmuio2-supply = <&vcca1v8_pmu>;
> +	vccio1-supply = <&vccio_acodec>;
> +	vccio2-supply = <&vcc_1v8>;
> +	vccio3-supply = <&vccio_sd>;
> +	vccio4-supply = <&vcca1v8_pmu>;
> +	vccio5-supply = <&vcc_3v3>;
> +	vccio6-supply = <&vcc_3v3>;
> +	vccio7-supply = <&vcc_3v3>;
> +	status = "okay";
> +};
> +
> +&saradc {
> +	vref-supply = <&vcca_1v8>;
> +	status = "okay";
> +};
> +
> +&sdhci {
> +	bus-width = <8>;
> +	max-frequency = <200000000>;

This board support HS200, please add:

  mmc-hs200-1_8v

> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vcc_1v8>;
> +	status = "okay";
> +};
> +
> +&sdmmc0 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;

Please drop the cd-gpios prop, sdmmc0_det is used below and works fine
on this board.

> +	disable-wp;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> +	sd-uhs-sdr50;

Why limit to sdr50? and not use sd-uhs-sdr104?

> +	vmmc-supply = <&vcc3v3_sd>;

If I read the scematics correctly this is using the vcc3v3_sys regulator
and not the vcc3v3_sd. R90724 is not connected however R90723 is and
this also matches visual inspection of the board.

> +	vqmmc-supply = <&vccio_sd>;
> +	status = "okay";
> +};
> +
> +&sdmmc1 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cap-sdio-irq;
> +	keep-power-in-suspend;
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd>;
> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vcc3v3_sys>;
> +	vqmmc-supply = <&vcca1v8_pmu>;
> +	status = "okay";
> +};
> +
> +&sfc {

This is missing pinctrl:

  pinctrl-names = "default";
  pinctrl-0 = <&fspi_pins>;

> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
> +
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0x0>;
> +		spi-max-frequency = <104000000>;

My board is using a GD25LQ128EWIGR same as mentioned in the schematic,
and datasheet for this flash chip menion 120 mhz and not 104 mhz.

Regards,
Jonas

> +		spi-rx-bus-width = <4>;
> +		spi-tx-bus-width = <1>;
> +	};
> +};
> +
> +&tsadc {
> +	rockchip,hw-tshut-mode = <1>;
> +	rockchip,hw-tshut-polarity = <0>;
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1m0_ctsn &uart1m0_rtsn &uart1m0_xfer>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	status = "okay";
> +};
> +
> +&usb_host0_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host0_ohci {
> +	status = "okay";
> +};
> +
> +&usb_host0_xhci {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&usb_host1_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host1_ohci {
> +	status = "okay";
> +};
> +
> +&usb_host1_xhci {
> +	status = "okay";
> +};
> +
> +&usb2phy0 {
> +	status = "okay";
> +};
> +
> +&usb2phy0_host {
> +	phy-supply = <&vcc5v0_usb_host>;
> +	status = "okay";
> +};
> +
> +&usb2phy0_otg {
> +	phy-supply = <&vcc5v0_usb_otg>;
> +	status = "okay";
> +};
> +
> +&usb2phy1 {
> +	status = "okay";
> +};
> +
> +&usb2phy1_host {
> +	phy-supply = <&vcc5v0_usb_host>;
> +	status = "okay";
> +};
> +
> +&usb2phy1_otg {
> +	phy-supply = <&vcc5v0_usb_host>;
> +	status = "okay";
> +};
> +
> +&vop {
> +	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> +	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> +	status = "okay";
> +};
> +
> +&vop_mmu {
> +	status = "okay";
> +};
> +
> +&vp0 {
> +	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
> +		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> +		remote-endpoint = <&hdmi_in_vp0>;
> +	};
> +};





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux