On Mon, Apr 8, 2024 at 5:14 AM Alexander Stein <alexander.stein@xxxxxxxxxxxxxxx> wrote: > > Hi everyone, > > Am Samstag, 6. April 2024, 04:58:39 CEST schrieb Marek Vasut: > > On 4/5/24 11:04 PM, Adam Ford wrote: > > > On Fri, Apr 5, 2024 at 3:43 PM Laurent Pinchart > > > <laurent.pinchart@xxxxxxxxxxxxxxxx> wrote: > > >> > > >> Hi Marek, > > >> > > >> (CC'ing Adam) > > >> > > >> Thank you for the patch. > > >> > > >> On Fri, Apr 05, 2024 at 10:22:26PM +0200, Marek Vasut wrote: > > >>> Configure both CSI2 assigned-clock-rates the same way. > > >>> There does not seem to be any reason for keeping the > > >>> two CSI2 pixel clock set to different frequencies. > > >> > > >> There's an issue when using two cameras concurrently. This has been > > >> discussed some time ago on the linux-media mailing list, see [1]. Adam > > >> knows more than I do on this topic. > > >> > > >> [1] https://lore.kernel.org/linux-media/CAHCN7x+kymRGO2kxvN2=zLiqRjfTc3hdf3VdNVkWjsW3La0bnA@xxxxxxxxxxxxxx/ > > >> > > >>> Signed-off-by: Marek Vasut <marex@xxxxxxx> > > >>> --- > > >>> Cc: Conor Dooley <conor+dt@xxxxxxxxxx> > > >>> Cc: Fabio Estevam <festevam@xxxxxxxxx> > > >>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx> > > >>> Cc: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > > >>> Cc: Paul Elder <paul.elder@xxxxxxxxxxxxxxxx> > > >>> Cc: Pengutronix Kernel Team <kernel@xxxxxxxxxxxxxx> > > >>> Cc: Rob Herring <robh@xxxxxxxxxx> > > >>> Cc: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> > > >>> Cc: Shawn Guo <shawnguo@xxxxxxxxxx> > > >>> Cc: devicetree@xxxxxxxxxxxxxxx > > >>> Cc: imx@xxxxxxxxxxxxxxx > > >>> Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > > >>> --- > > >>> arch/arm64/boot/dts/freescale/imx8mp.dtsi | 2 +- > > >>> 1 file changed, 1 insertion(+), 1 deletion(-) > > >>> > > >>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi > > >>> index 1bb96e96639f2..2e9ce0c3a9815 100644 > > >>> --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi > > >>> +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi > > >>> @@ -1703,7 +1703,7 @@ mipi_csi_1: csi@32e50000 { > > >>> <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>; > > >>> assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>, > > >>> <&clk IMX8MP_CLK_24M>; > > >>> - assigned-clock-rates = <266000000>; > > >>> + assigned-clock-rates = <500000000>; > > > > > > I am traveling, so I don't have the technical documents in front of > > > me, but I beleive this is an over-drive speed, and 400MHz would be the > > > single clock, standard rate. I created an imx8mm-overdrive and > > > imx8mn-overdrive dtsi file to let users who operate in overdrive mode > > > to update their clocks in one place. > > > > > > I also think this goes down if the user is running two cameras instead > > > of one. I re-read the old thread, and it's coming back to me, but > > > until I can get settled into my hotel in Germany, I won't have time to > > > review. I think the original idea was to use the lowest, conservative > > > value with the idea that people can tweak their clock settings if > > > they're only running one and if they are running in over-drive mode. > > > > MX8MPCEC does indeed read 400 MHz regular, 500 MHz overdrive. > > > > Shall we align both CSI2 ports to 400 MHz ? Currently they are one 500 > > MHz and the other 266 MHz . > > No, that won't do. The (industrial products) datasheet says (Table 1): > * Single camera on CSI1: 400/500 MHz in normal/overdrive mode > * Single camera on CSI2: 277 MHz > * Dual camera on CSI1 & CSI2: 266 MHz > > Assuming you need CSI2 more likely in a dual camera setup only, defaulting to > 266MHz seems sensible to me. I agree. I think that at a minimum, the 500MHz clock should be reduced to 400MHz since 500MHz requires overdrive mode, but the safest clock rate would be to set both to 266MHz. Would it be appropriate to add a note to the device tree indicating that a single camera operating mode could potentially increase this to 400/500 depending on overdrive mode? adam > > Best regards, > Alexander > -- > TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany > Amtsgericht München, HRB 105018 > Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider > http://www.tq-group.com/ > >
