On Fri, Dec 12, 2014 at 11:47:49AM +0100, Philipp Zabel wrote: > Some board designers, when running out of clock output pads, decide to > (mis)use PWM output pads to provide a clock to external components. > This driver supports this practice by providing an adapter between the > PWM and clock bindings in the device tree. As the PWM bindings specify > the period in the device tree, this is a fixed clock. Typically the period is specified in DT because it is a board-level characteristic. In this case where you emulate a clock using the PWM channel you could simply ignore the period. After all you can freely choose it during pwm_config() irrespective of the period specified in DT. Other than that looks mostly good to me, just a few nits below. [...] > diff --git a/Documentation/devicetree/bindings/clock/pwm-clock.txt b/Documentation/devicetree/bindings/clock/pwm-clock.txt > new file mode 100644 > index 0000000..751fff5 > --- /dev/null > +++ b/Documentation/devicetree/bindings/clock/pwm-clock.txt > @@ -0,0 +1,26 @@ > +Binding for an external clock signal driven by a PWM pin. > + > +This binding uses the common clock binding[1] and the common PWM binding[2]. > + > +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt > +[2] Documentation/devicetree/bindings/pwm/pwm.txt > + > +Required properties: > +- compatible : shall be "pwm-clock". > +- #clock-cells : from common clock binding; shall be set to 0. > +- pwms : from common PWM binding; this determines the clock frequency > + via the PWM period given in the pwm-specifier. Perhaps: "the period given in the PWM specifier"? > +Optional properties: > +- clock-output-names : From common clock binding. > +- clock-frequency : Exact output frequency, in case the pwm period "PWM period" > + is not exact but was rounded to nanoseconds. Does this make sense? For one it's now easy to specify two different values for the frequency, one using the PWM specifier, the other with clock-frequency. According to the above, clock-frequency takes precedence, but in that case, what use is there in having the PWM specifier? > diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig > index 455fd17..36a6918a 100644 > --- a/drivers/clk/Kconfig > +++ b/drivers/clk/Kconfig > @@ -129,6 +129,13 @@ config COMMON_CLK_PALMAS > This driver supports TI Palmas devices 32KHz output KG and KG_AUDIO > using common clock framework. > > +config COMMON_CLK_PWM > + bool "Clock driver for PWMs used as clock outputs" > + depends on PWM > + ---help--- > + Adapter driver so that any PWM output can be (mis)used as clock signal > + at 50% duty cycle. Any reason why this isn't tristate? > config COMMON_CLK_PXA > def_bool COMMON_CLK && ARCH_PXA > ---help--- [...] > diff --git a/drivers/clk/clk-pwm.c b/drivers/clk/clk-pwm.c > new file mode 100644 > index 0000000..c7d5652 > --- /dev/null > +++ b/drivers/clk/clk-pwm.c > @@ -0,0 +1,129 @@ > +/* > + * Copyright (C) 2014 Philipp Zabel, Pengutronix > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * PWM (mis)used as clock output > + */ > +#include <linux/clk-provider.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/pwm.h> > + > +struct clk_pwm { > + struct clk_hw hw; > + struct pwm_device *pwm; > + u32 fixed_rate; > +}; > + > +#define to_clk_pwm(_hw) container_of(_hw, struct clk_pwm, hw) Perhaps use a static inline so you get proper type checking? > +int clk_pwm_probe(struct platform_device *pdev) > +{ > + struct device_node *node = pdev->dev.of_node; > + struct clk_init_data init; > + struct clk_pwm *clk_pwm; > + struct pwm_device *pwm; > + const char *clk_name; > + struct clk *clk; > + int ret; > + > + clk_pwm = devm_kzalloc(&pdev->dev, sizeof(*clk_pwm), GFP_KERNEL); > + if (!clk_pwm) > + return -ENOMEM; > + > + pwm = devm_pwm_get(&pdev->dev, NULL); > + if (IS_ERR(pwm)) > + return PTR_ERR(pwm); > + > + if (!pwm || !pwm->period) { I don't think there's a case where pwm can be NULL here. > + dev_err(&pdev->dev, "invalid pwm period\n"); "PWM" > + return -EINVAL; > + } > + > + if (of_property_read_u32(node, "clock-frequency", &clk_pwm->fixed_rate)) > + clk_pwm->fixed_rate = NSEC_PER_SEC / pwm->period; > + > + if (pwm->period != NSEC_PER_SEC / clk_pwm->fixed_rate && > + pwm->period != DIV_ROUND_UP(NSEC_PER_SEC, clk_pwm->fixed_rate)) { > + dev_err(&pdev->dev, > + "clock-frequency does not match pwm period\n"); "PWM" > +static struct platform_driver clk_pwm_driver = { > + .probe = clk_pwm_probe, > + .remove = clk_pwm_remove, > + .driver = { > + .name = "pwm-clock", > + .of_match_table = of_match_ptr(clk_pwm_dt_ids), > + }, > +}; > + > +module_platform_driver(clk_pwm_driver); This is missing MODULE_AUTHOR, MODULE_DESCRIPTION and MODULE_LICENSE. Thierry
Attachment:
pgpMSp8rYQ9nY.pgp
Description: PGP signature