Re: [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi,

Few comments below.

* Marek Belisko <marek@xxxxxxxxxxxxx> [150212 05:07]:
> +
> +&omap3_pmx_core {
> +
> +	mmc1_pins: pinmux_mmc1_pins {
> +		pinctrl-single,pins = <
> +			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
> +			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
> +			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat0.sdmmc1_dat0 */
> +			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat1.sdmmc1_dat1 */
> +			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat2.sdmmc1_dat2 */
> +			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat3.sdmmc1_dat3 */
> +		>;
...

> +&omap3_pmx_core2 {
> +	/* define in CPU specific file that includes this one
> +	 * use either OMAP3430_CORE2_IOPAD() or OMAP3630_CORE2_IOPAD()
> +	 */
> +};

OK looks like you have some SoC specific pins too.. I assume you
guys have checked that all the pins defined in this file are at
the same offset between 34xx and 36xx variants?

> +&i2c1 {
> +	clock-frequency = <2600000>;
> +
> +	twl: twl@48 {
> +		reg = <0x48>;
> +		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
> +		interrupt-parent = <&intc>;
> +
> +		twl_power: power {
> +			compatible = "ti,twl4030-power-reset";
> +			ti,use_poweroff;
> +		};
> +
> +		twl_audio: audio {
> +			compatible = "ti,twl4030-audio";
> +
> +			codec {
> +				ti,ramp_delay_value = <3>;
> +			};
> +		};
> +	};
> +};

Can be done later naturally, but ere you probably want
ti,twl4030-power-idle or ti,twl4030-power-idle-osc-off
if the osicllator can be shut down during off-idle.

> +&gpmc {
> +	ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */

The ranges here allocate the GPMC partition, so it needs to be
a minimum of 16MB:

	ranges = <0 0 0x30000000 0x1000000>,	/* CS0: 16MB for NAND */

> +	nand@0,0 {
> +		reg = <0 0 0>; /* CS0, offset 0 */

The reg is for the device driver to ioremap it's registers,
for NAND it's just 4:

		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */

> +		filesystem@680000 {
> +			label = "rootfs";
> +			reg = <0xc80000 0>;	/* 0 = MTDPART_SIZ_FULL */
> +		};
> +	};
> +};

Is the NAND the same size on all of them? I don't think dts
has a binding for MTDPART_SIZ_FULL type thing..

> +	lcd: lcd@1 {
> +		reg = <1>;	/* CS1 */
> +		compatible =	"omapdss,tpo,td043mtea1";
> +		spi-max-frequency = <100000>;
> +		spi-cpol;
> +		spi-cpha;
> +
> +		label = "lcd";
> +		reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;	/* GPIO_157 */
> +		vcc-supply = <&vaux1>;
> +
> +		port {
> +			lcd_in: endpoint {
> +				remote-endpoint = <&dpi_out>;
> +			};
> +		};
> +	};

Oh there's already a binding for the LCD too? That's great :)

Nine job, good to see this happening!

Regards,


Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux