The binding dictates using 3 pwm-cells. Adhere to that. This fixes the following dtbs_check warnings: arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml# arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml# arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml# arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml# arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml# arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml# Signed-off-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx> --- arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi index 42b2ba23aefc..a308a3584b62 100644 --- a/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi +++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi @@ -66,7 +66,7 @@ lvds_backlight: lvds-backlight { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lvds_bl>; enable-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; - pwms = <&pwm1 0 50000>; + pwms = <&pwm1 0 50000 0>; brightness-levels = < 0 4 8 16 32 64 80 96 112 128 144 160 176 250 @@ -78,7 +78,7 @@ lvds_backlight: lvds-backlight { pwm_fan: pwm-fan { compatible = "pwm-fan"; #cooling-cells = <2>; - pwms = <&pwm4 0 50000>; + pwms = <&pwm4 0 50000 0>; cooling-levels = <0 64 127 191 255>; status = "disabled"; }; @@ -145,7 +145,7 @@ rgb_backlight: rgb-backlight { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_rgb_bl>; enable-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>; - pwms = <&pwm3 0 5000000>; + pwms = <&pwm3 0 5000000 0>; brightness-levels = < 250 176 160 144 128 112 96 80 64 48 32 16 8 1 @@ -736,17 +736,14 @@ &pcie { }; &pwm1 { - #pwm-cells = <2>; status = "okay"; }; &pwm3 { - #pwm-cells = <2>; status = "okay"; }; &pwm4 { - #pwm-cells = <2>; status = "okay"; }; -- 2.43.0
