From: Stefan Eichenberger <stefan.eichenberger@xxxxxxxxxxx>
The Verdin family has a signal called sleep-moci which can be used to
turn off peripherals on the carrier board when the SoM goes into
suspend. So far we have hogged this signal, which means the peripherals
are always on and it is not possible to add peripherals that depend on
the sleep-moci to be on. With this change, we replace the hog with a
regulator so that peripherals can add their own regulators that use the
same gpio. Carrier boards that allow peripherals to be powered off in
suspend can disable this regulator and implement their own regulator to
control the sleep-moci.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@xxxxxxxxxxx>
---
.../dts/freescale/imx8mm-verdin-dahlia.dtsi | 5 ++++
.../boot/dts/freescale/imx8mm-verdin-dev.dtsi | 5 ++++
.../dts/freescale/imx8mm-verdin-yavia.dtsi | 5 ++++
.../boot/dts/freescale/imx8mm-verdin.dtsi | 26 ++++++++++++-------
4 files changed, 31 insertions(+), 10 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
index 1cff0b829357..b64dac4f29c2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
@@ -58,6 +58,11 @@ &flexspi {
status = "okay";
};
+&gpio5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+};
+
/* Current measurement into module VCC */
&hwmon {
status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
index 3c4b8ca125e3..95b7c9a03a23 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -78,6 +78,11 @@ &i2c3 {
status = "okay";
};
+&gpio5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+};
+
&gpio_expander_21 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi
index 1e28c78e381f..763f069e8405 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi
@@ -81,6 +81,11 @@ &gpio3 {
pinctrl-0 = <&pinctrl_gpios_ext_yavia>;
};
+&gpio5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+};
+
&hwmon_temp {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
index 6f0811587142..4768b05fd765 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
@@ -110,6 +110,22 @@ reg_ethphy: regulator-ethphy {
startup-delay-us = <200000>;
};
+ /*
+ * By default we enable CTRL_SLEEP_MOCI#, this is required to have
+ * peripherals on the carrier board powered.
+ * If more granularity or power saving is required this can be disabled
+ * in the carrier board device tree files.
+ */
+ reg_force_sleep_moci: regulator-force-sleep-moci {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ /* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+ gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "CTRL_SLEEP_MOCI#";
+ };
+
reg_usb_otg1_vbus: regulator-usb-otg1 {
compatible = "regulator-fixed";
enable-active-high;
@@ -333,16 +349,6 @@ &gpio5 {
"SODIMM_212",
"SODIMM_151",
"SODIMM_153";
-
- ctrl-sleep-moci-hog {
- gpio-hog;
- /* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
- gpios = <1 GPIO_ACTIVE_HIGH>;
- line-name = "CTRL_SLEEP_MOCI#";
- output-high;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
- };
};
/* On-module I2C */
--
2.40.1
