Re: [PATCH v4 4/4] arm64: dts: S32G3: Introduce device tree for S32G-VNP-RDB3

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Mar 24, 2024 at 10:43:26PM +0100, Wadim Mueller wrote:
> This commit adds device tree support for the NXP S32G3-based
> S32G-VNP-RDB3 Board [1].
> 
> The S32G3 features an 8-core ARM Cortex-A53 based SoC developed by NXP.
> 
> The device tree files are derived from the official NXP downstream
> Linux tree [2].
> 
> This addition encompasses a limited selection of peripherals that
> are upstream-supported. Apart from the ARM System Modules
> (GIC, Generic Timer, etc.), the following IPs have been validated:
> 
>     * UART: fsl-linflexuart
>     * SDHC: fsl-imx-esdhc
> 
> Clock settings for the chip rely on ATF Firmware [3].
> Pin control integration into the device tree is pending and currently
> relies on Firmware/U-Boot settings [4].
> 
> These changes were validated using BSP39 Firmware/U-Boot from NXP [5].
> 
> The modifications enable booting the official Ubuntu 22.04 from NXP on
> the RDB3 with default settings from the SD card and eMMC.
> 
> [1] https://www.nxp.com/design/design-center/designs/s32g3-vehicle-networking-reference-design:S32G-VNP-RDB3
> [2] https://github.com/nxp-auto-linux/linux
> [3] https://github.com/nxp-auto-linux/arm-trusted-firmware
> [4] https://github.com/nxp-auto-linux/u-boot
> [5] https://github.com/nxp-auto-linux/auto_yocto_bsp
> 
> Signed-off-by: Wadim Mueller <wafgo01@xxxxxxxxx>
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  arch/arm64/boot/dts/freescale/s32g3.dtsi      | 233 ++++++++++++++++++
>  .../boot/dts/freescale/s32g399a-rdb3.dts      |  45 ++++
>  3 files changed, 279 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/s32g3.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 2cb0212b63c6..e701008dbc7b 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -252,3 +252,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw74xx-rpidsi.dtb
>  dtb-$(CONFIG_ARCH_S32) += s32g274a-evb.dtb
>  dtb-$(CONFIG_ARCH_S32) += s32g274a-rdb2.dtb
>  dtb-$(CONFIG_ARCH_S32) += s32v234-evb.dtb
> +dtb-$(CONFIG_ARCH_S32) += s32g399a-rdb3.dtb

The list is alphabetically sorted, so it should be added before
s32v234-evb.dtb.  I fixed it up and applied the patch.

Shawn





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux