On Fri 29 Mar 2024 at 23:58, Dmitry Rokosov <ddrokosov@xxxxxxxxxxxxxxxxx> wrote:
> The 'syspll' PLL, also known as the system PLL, is a general and
> essential PLL responsible for generating the CPU clock frequency.
> With its wide-ranging capabilities, it is designed to accommodate
> frequencies within the range of 768MHz to 1536MHz.
>
> Signed-off-by: Dmitry Rokosov <ddrokosov@xxxxxxxxxxxxxxxxx>
> ---
> drivers/clk/meson/a1-pll.c | 78 ++++++++++++++++++++++++++++++++++++++
> drivers/clk/meson/a1-pll.h | 6 +++
> 2 files changed, 84 insertions(+)
>
> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
> index 60b2e53e7e51..02fd2d325cc6 100644
> --- a/drivers/clk/meson/a1-pll.c
> +++ b/drivers/clk/meson/a1-pll.c
> @@ -138,6 +138,81 @@ static struct clk_regmap hifi_pll = {
> },
> };
>
> +static const struct pll_mult_range sys_pll_mult_range = {
> + .min = 32,
> + .max = 64,
> +};
> +
> +/*
> + * We assume that the sys_pll_clk has already been set up by the low-level
> + * bootloaders as the main CPU PLL source. Therefore, it is not necessary to
> + * run the initialization sequence.
> + */
I see no reason to make such assumption.
This clock is no read-only, it apparently is able to re-lock so assuming
anything from the bootloader is just asking from trouble
> +static struct clk_regmap sys_pll = {
> + .data = &(struct meson_clk_pll_data){
> + .en = {
> + .reg_off = ANACTRL_SYSPLL_CTRL0,
> + .shift = 28,
> + .width = 1,
> + },
> + .m = {
> + .reg_off = ANACTRL_SYSPLL_CTRL0,
> + .shift = 0,
> + .width = 8,
> + },
> + .n = {
> + .reg_off = ANACTRL_SYSPLL_CTRL0,
> + .shift = 10,
> + .width = 5,
> + },
> + .frac = {
> + .reg_off = ANACTRL_SYSPLL_CTRL1,
> + .shift = 0,
> + .width = 19,
> + },
> + .l = {
> + .reg_off = ANACTRL_SYSPLL_STS,
> + .shift = 31,
> + .width = 1,
> + },
> + .current_en = {
> + .reg_off = ANACTRL_SYSPLL_CTRL0,
> + .shift = 26,
> + .width = 1,
> + },
> + .l_detect = {
> + .reg_off = ANACTRL_SYSPLL_CTRL2,
> + .shift = 6,
> + .width = 1,
> + },
> + .range = &sys_pll_mult_range,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "sys_pll",
> + .ops = &meson_clk_pll_ops,
> + .parent_names = (const char *[]){ "syspll_in" },
> + .num_parents = 1,
> + /*
> + * This clock is used as the main CPU PLL source in low-level
> + * bootloaders, and it is necessary to mark it as critical.
> + */
> + .flags = CLK_IS_CRITICAL,
No I don't think so. Downstream consumer maybe critical but that one is
not, unless it is read-only.
A CPU pll, like on the g12 family, is unlikely to be read-only since the
PLL will need to relock to change rates. During this phase, there will
be no reate coming from the PLL so the PLL is not critical and you must
be able to "park" your CPU an another clock while poking this one
> + },
> +};
> +
> +static struct clk_fixed_factor sys_pll_div16 = {
> + .mult = 1,
> + .div = 16,
> + .hw.init = &(struct clk_init_data){
> + .name = "sys_pll_div16",
> + .ops = &clk_fixed_factor_ops,
> + .parent_hws = (const struct clk_hw *[]) {
> + &sys_pll.hw
> + },
> + .num_parents = 1,
> + },
> +};
> +
> static struct clk_fixed_factor fclk_div2_div = {
> .mult = 1,
> .div = 2,
> @@ -283,6 +358,8 @@ static struct clk_hw *a1_pll_hw_clks[] = {
> [CLKID_FCLK_DIV5] = &fclk_div5.hw,
> [CLKID_FCLK_DIV7] = &fclk_div7.hw,
> [CLKID_HIFI_PLL] = &hifi_pll.hw,
> + [CLKID_SYS_PLL] = &sys_pll.hw,
> + [CLKID_SYS_PLL_DIV16] = &sys_pll_div16.hw,
> };
>
> static struct clk_regmap *const a1_pll_regmaps[] = {
> @@ -293,6 +370,7 @@ static struct clk_regmap *const a1_pll_regmaps[] = {
> &fclk_div5,
> &fclk_div7,
> &hifi_pll,
> + &sys_pll,
> };
>
> static struct regmap_config a1_pll_regmap_cfg = {
> diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
> index 4be17b2bf383..666d9b2137e9 100644
> --- a/drivers/clk/meson/a1-pll.h
> +++ b/drivers/clk/meson/a1-pll.h
> @@ -18,6 +18,12 @@
> #define ANACTRL_FIXPLL_CTRL0 0x0
> #define ANACTRL_FIXPLL_CTRL1 0x4
> #define ANACTRL_FIXPLL_STS 0x14
> +#define ANACTRL_SYSPLL_CTRL0 0x80
> +#define ANACTRL_SYSPLL_CTRL1 0x84
> +#define ANACTRL_SYSPLL_CTRL2 0x88
> +#define ANACTRL_SYSPLL_CTRL3 0x8c
> +#define ANACTRL_SYSPLL_CTRL4 0x90
> +#define ANACTRL_SYSPLL_STS 0x94
> #define ANACTRL_HIFIPLL_CTRL0 0xc0
> #define ANACTRL_HIFIPLL_CTRL1 0xc4
> #define ANACTRL_HIFIPLL_CTRL2 0xc8
--
Jerome
