On Thu, Mar 21, 2024 at 04:14:31PM +0800, Xu Yang wrote: > Enable 2 USB nodes and add 2 PTN5150 nodes on i.MX8ULP evk board. > > Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx> > > --- > Changes in v2: > - fix format as suggusted by Fabio > - add PTN5150 nodes > Changes in v3: > - no changes > Changes in v4: > - no changes > Changes in v5: > - no changes > Changes in v6: > - no changes > Changes in v7: > - no changes > Changes in v8: > - no changes > Changes in v9: > - no changes > Changes in v10: > - no changes > --- > arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 84 +++++++++++++++++++ > 1 file changed, 84 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > index 69dd8e31027c..bf418af31039 100644 > --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > @@ -133,6 +133,64 @@ pcal6408: gpio@21 { > gpio-controller; > #gpio-cells = <2>; > }; > + > + ptn5150_1: typec@1d { Could you sort devices in unit-address? > + compatible = "nxp,ptn5150"; > + reg = <0x1d>; > + int-gpios = <&gpiof 3 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_typec1>; > + status = "disabled"; > + }; > + > + ptn5150_2: typec@3d { > + compatible = "nxp,ptn5150"; > + reg = <0x3d>; > + int-gpios = <&gpiof 5 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; Broken indent? Shawn > + pinctrl-0 = <&pinctrl_typec2>; > + status = "disabled"; > + }; > +}; > + > +&usbotg1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb1>; > + dr_mode = "otg"; > + hnp-disable; > + srp-disable; > + adp-disable; > + over-current-active-low; > + status = "okay"; > +}; > + > +&usbphy1 { > + fsl,tx-d-cal = <110>; > + status = "okay"; > +}; > + > +&usbmisc1 { > + status = "okay"; > +}; > + > +&usbotg2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb2>; > + dr_mode = "otg"; > + hnp-disable; > + srp-disable; > + adp-disable; > + over-current-active-low; > + status = "okay"; > +}; > + > +&usbphy2 { > + fsl,tx-d-cal = <110>; > + status = "okay"; > +}; > + > +&usbmisc2 { > + status = "okay"; > }; > > &usdhc0 { > @@ -224,6 +282,32 @@ MX8ULP_PAD_PTE13__LPI2C7_SDA 0x20 > >; > }; > > + pinctrl_typec1: typec1grp { > + fsl,pins = < > + MX8ULP_PAD_PTF3__PTF3 0x3 > + >; > + }; > + > + pinctrl_typec2: typec2grp { > + fsl,pins = < > + MX8ULP_PAD_PTF5__PTF5 0x3 > + >; > + }; > + > + pinctrl_usb1: usb1grp { > + fsl,pins = < > + MX8ULP_PAD_PTF2__USB0_ID 0x10003 > + MX8ULP_PAD_PTF4__USB0_OC 0x10003 > + >; > + }; > + > + pinctrl_usb2: usb2grp { > + fsl,pins = < > + MX8ULP_PAD_PTD23__USB1_ID 0x10003 > + MX8ULP_PAD_PTF6__USB1_OC 0x10003 > + >; > + }; > + > pinctrl_usdhc0: usdhc0grp { > fsl,pins = < > MX8ULP_PAD_PTD1__SDHC0_CMD 0x3 > -- > 2.34.1 >