On 3/27/24 01:53, Peter Yin wrote:
Add WDIOF_EXTERN1 and WDIOF_CARDRESET bootstatus in ast2600
Regarding the AST2600 specification, the WDTn Timeout Status Register
(WDT10) has bit 1 reserved. Bit 1 of the status register indicates
on ast2500 if the boot was from the second boot source.
It does not indicate that the most recent reset was triggered by
the watchdog. The code should just be changed to set WDIOF_CARDRESET
if bit 0 of the status register is set.
Include SCU register to veriy WDIOF_EXTERN1 in ast2600 SCU74 or
ast2500 SCU3C when bit1 is set.
Signed-off-by: Peter Yin <peteryin.openbmc@xxxxxxxxx>
---
drivers/watchdog/aspeed_wdt.c | 60 +++++++++++++++++++++++++----------
1 file changed, 44 insertions(+), 16 deletions(-)
diff --git a/drivers/watchdog/aspeed_wdt.c b/drivers/watchdog/aspeed_wdt.c
index b4773a6aaf8c..29e9afdee619 100644
--- a/drivers/watchdog/aspeed_wdt.c
+++ b/drivers/watchdog/aspeed_wdt.c
@@ -11,10 +11,12 @@
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/kstrtox.h>
+#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/platform_device.h>
+#include <linux/regmap.h>
#include <linux/watchdog.h>
static bool nowayout = WATCHDOG_NOWAYOUT;
@@ -65,23 +67,32 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
#define WDT_RELOAD_VALUE 0x04
#define WDT_RESTART 0x08
#define WDT_CTRL 0x0C
-#define WDT_CTRL_BOOT_SECONDARY BIT(7)
-#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5)
-#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5)
-#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5)
-#define WDT_CTRL_1MHZ_CLK BIT(4)
-#define WDT_CTRL_WDT_EXT BIT(3)
-#define WDT_CTRL_WDT_INTR BIT(2)
-#define WDT_CTRL_RESET_SYSTEM BIT(1)
-#define WDT_CTRL_ENABLE BIT(0)
+#define WDT_CTRL_BOOT_SECONDARY BIT(7)
+#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5)
+#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5)
+#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5)
+#define WDT_CTRL_1MHZ_CLK BIT(4)
+#define WDT_CTRL_WDT_EXT BIT(3)
+#define WDT_CTRL_WDT_INTR BIT(2)
+#define WDT_CTRL_RESET_SYSTEM BIT(1)
+#define WDT_CTRL_ENABLE BIT(0)
#define WDT_TIMEOUT_STATUS 0x10
-#define WDT_TIMEOUT_STATUS_IRQ BIT(2)
-#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1)
+#define WDT_TIMEOUT_STATUS_IRQ BIT(2)
+#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1)
+#define WDT_TIMEOUT_STATUS_EVENT BIT(0)
#define WDT_CLEAR_TIMEOUT_STATUS 0x14
-#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0)
+#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0)
#define WDT_RESET_MASK1 0x1c
#define WDT_RESET_MASK2 0x20
The above bit value defines were indented to show what is
registers and what is register bit values. Why are you
changing that other than for personal preference ?
Guenter
