Document the SelectMAP interface of Xilinx 7 series FPGA. Signed-off-by: Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> --- .../bindings/fpga/xlnx,fpga-selectmap.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml diff --git a/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml b/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml new file mode 100644 index 0000000000000..05775746fd706 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/fpga/xlnx,fpga-selectmap.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx SelectMAP FPGA interface + +maintainers: + - Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx> + +description: | + Xilinx 7 Series FPGAs support a method of loading the bitstream over a + parallel port named the SelectMAP interface in the documentation. Only + the x8 mode is supported where data is loaded at one byte per rising edge of + the clock, with the MSB of each byte presented to the D0 pin. + + Datasheets: + https://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf + +allOf: + - $ref: /schemas/memory-controllers/mc-peripheral-props.yaml# + +properties: + compatible: + enum: + - xlnx,fpga-xc7s-selectmap + - xlnx,fpga-xc7a-selectmap + - xlnx,fpga-xc7k-selectmap + - xlnx,fpga-xc7v-selectmap + + reg: + description: + At least 1 byte of memory mapped IO + maxItems: 1 + + prog-gpios: + description: + config pin (referred to as PROGRAM_B in the manual) + maxItems: 1 + + done-gpios: + description: + config status pin (referred to as DONE in the manual) + maxItems: 1 + + init-gpios: + description: + initialization status and configuration error pin + (referred to as INIT_B in the manual) + maxItems: 1 + + csi-gpios: + description: + chip select pin (referred to as CSI_B in the manual) + Optional gpio for if the bus controller does not provide a chip select. + maxItems: 1 + + rdwr-gpios: + description: + read/write select pin (referred to as RDWR_B in the manual) + Optional gpio for if the bus controller does not provide this pin. + maxItems: 1 + +required: + - compatible + - reg + - prog-gpios + - done-gpios + - init-gpios + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + fpga-mgr@8000000 { + compatible = "xlnx,fpga-xc7s-selectmap"; + reg = <0x8000000 0x4>; + prog-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; + init-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; + done-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>; + csi-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + rdwr-gpios = <&gpio3 10 GPIO_ACTIVE_LOW>; + }; +... -- 2.43.0