Re: [PATCH v2 4/6] arm64: dts: qcom: sc8180x-lenovo-flex-5g: enable touchscreen

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



March 18, 2024 at 4:43 AM, "Bjorn Andersson" <andersson@xxxxxxxxxx> wrote:



> 
> On Sat, Feb 03, 2024 at 09:11:58PM +0200, Anton Bambura wrote:
> 
> > 
> > Set regulators, reset gpio and delays according to ACPI tables.
> > 
> >  
> > 
> >  Signed-off-by: Anton Bambura <jenneron@xxxxxxxxxxxxxxxx>
> > 
> >  ---
> > 
> >  .../boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 30 ++++++++++++++++++-
> > 
> >  1 file changed, 29 insertions(+), 1 deletion(-)
> > 
> >  
> > 
> >  diff --git a/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
> > 
> >  index 6ae6cb030b70..5bf6285f905f 100644
> > 
> >  --- a/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
> > 
> >  +++ b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
> > 
> >  @@ -271,6 +271,12 @@ vreg_l3c_1p2: ldo3 {
> > 
> >  regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > 
> >  };
> > 
> >  
> > 
> >  + vreg_l4c_3p3: ldo4 {
> > 
> >  + regulator-min-microvolt = <3296000>;
> > 
> >  + regulator-max-microvolt = <3304000>;
> > 
> >  + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > 
> >  + };
> > 
> >  +
> > 
> >  vreg_l10c_3p3: ldo10 {
> > 
> >  regulator-min-microvolt = <3000000>;
> > 
> >  regulator-max-microvolt = <3312000>;
> > 
> >  @@ -337,6 +343,12 @@ vreg_l10e_2p9: ldo10 {
> > 
> >  regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > 
> >  };
> > 
> >  
> > 
> >  + vreg_l12e_1p8: ldo12 {
> > 
> >  + regulator-min-microvolt = <1800000>;
> > 
> >  + regulator-max-microvolt = <1800000>;
> > 
> >  + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > 
> >  + };
> > 
> >  +
> > 
> >  vreg_l16e_3p0: ldo16 {
> > 
> >  regulator-min-microvolt = <3072000>;
> > 
> >  regulator-max-microvolt = <3072000>;
> > 
> >  @@ -365,11 +377,19 @@ &i2c1 {
> > 
> >  touchscreen@10 {
> > 
> >  compatible = "hid-over-i2c";
> > 
> >  reg = <0x10>;
> > 
> >  +
> > 
> >  hid-descr-addr = <0x1>;
> > 
> >  + reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
> > 
> >  +
> > 
> >  + vdd-supply = <&vreg_l4c_3p3>;
> > 
> >  + vddl-supply = <&vreg_l12e_1p8>;
> > 
> >  +
> > 
> >  + post-power-on-delay-ms = <3>;
> > 
> >  + post-reset-deassert-delay-ms = <200>;
> > 
> 
> As I ran into with the X13s, post-reset-deassert-delay-ms is not an
> 
> accepted property for hid-over-i2c. I think the desired path forward is
> 
> to extend elan,ekth6915.yaml and i2c-hid-of-elan.c and hard code these
> 
> values there instead.
> 
> But I suspect you, like me, are unaware of the actual name of the
> 
> device? Perhaps it's acceptable to make something up based on the
> 
> reported product id?

Indeed, I don't know the actual IC. evtest reports this:

Input device ID: bus 0x18 vendor 0x4f3 product 0x2a7d version 0x100
Input device name: "hid-over-i2c 04F3:2A7D"

> 
> Regards,
> 
> Bjorn
> 
> > 
> > interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>;
> > 
> >  
> > 
> >  - pinctrl-0 = <&ts_int_default>;
> > 
> >  + pinctrl-0 = <&ts_int_default>, <&ts_reset_default>;
> > 
> >  pinctrl-names = "default";
> > 
> >  };
> > 
> >  };
> > 
> >  @@ -735,6 +755,14 @@ ts_int_default: ts-int-default-state {
> > 
> >  drive-strength = <2>;
> > 
> >  };
> > 
> >  
> > 
> >  + ts_reset_default: ts-reset-default-state {
> > 
> >  + pins = "gpio54";
> > 
> >  + function = "gpio";
> > 
> >  +
> > 
> >  + bias-disable;
> > 
> >  + drive-strength = <16>;
> > 
> >  + };
> > 
> >  +
> > 
> >  usbprim_sbu_default: usbprim-sbu-state {
> > 
> >  oe-n-pins {
> > 
> >  pins = "gpio152";
> > 
> >  -- 
> > 
> >  2.42.0
> >
>





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux