Re: [PATCH 2/3] arm64: dts: qcom: qdu1000-idp: enable USB nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 19 Mar 2024 at 11:11, Komal Bajaj <quic_kbajaj@xxxxxxxxxxx> wrote:
>
> Enable both USB controllers and associated hsphy and qmp phy
> nodes on QDU1000 IDP. Add the usb type B port linked with the
> DWC3 USB controller switched to OTG mode and tagged with
> usb-role-switch.
>
> Co-developed-by: Amrit Anand <quic_amrianan@xxxxxxxxxxx>
> Signed-off-by: Amrit Anand <quic_amrianan@xxxxxxxxxxx>
> Signed-off-by: Komal Bajaj <quic_kbajaj@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/qdu1000-idp.dts | 65 ++++++++++++++++++++++++
>  1 file changed, 65 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qdu1000-idp.dts b/arch/arm64/boot/dts/qcom/qdu1000-idp.dts
> index 89b84fb0f70a..26442e707b5e 100644
> --- a/arch/arm64/boot/dts/qcom/qdu1000-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/qdu1000-idp.dts
> @@ -46,6 +46,33 @@ ppvar_sys: ppvar-sys-regulator {
>                 regulator-boot-on;
>         };
>
> +       usb_conn_gpio: usb-conn-gpio {
> +               compatible = "gpio-usb-b-connector";

If this board has only a USB-B connector, can it really handle USB 3.0?

> +               vbus-gpio =  <&pm8150_gpios 7 GPIO_ACTIVE_HIGH>;
> +               id-gpio = <&tlmm 42 GPIO_ACTIVE_HIGH>;
> +               vbus-supply = <&vbus_supply_regulator>;
> +
> +               pinctrl-0 = <&usb_vbus_det_default
> +                            &usb_id_det_default>;
> +               pinctrl-names = "default";
> +
> +               port {
> +                       usb_port0_connector: endpoint {
> +                               remote-endpoint = <&usb_1_dwc3_hs>;
> +                       };
> +               };
> +       };
> +
> +       vbus_supply_regulator: vbus-supply-regulator {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vbus_supply";
> +
> +               gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>;
> +               pinctrl-0 = <&usb_vbus_boost_default>;
> +               pinctrl-names = "default";
> +               enable-active-high;
> +       };
> +
>         vph_pwr: vph-pwr-regulator {
>                 compatible = "regulator-fixed";
>                 regulator-name = "vph_pwr";
> @@ -239,6 +266,16 @@ vreg_l18a_1p2: ldo18 {
>         };
>  };
>
> +&pm8150_gpios {
> +       usb_vbus_det_default: usb-vbus-det-default {
> +               pins = "gpio7";
> +               function = "normal";
> +               input-enable;
> +               bias-pull-up;
> +               power-source = <0>;
> +       };
> +};
> +
>  &qup_i2c1_data_clk {
>         drive-strength = <2>;
>         bias-pull-up;
> @@ -500,3 +537,31 @@ &tlmm {
>  &uart7 {
>         status = "okay";
>  };
> +
> +&usb_1 {
> +       status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +       dr_mode = "otg";

Nit: this is the default setting.

> +       usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> +       remote-endpoint = <&usb_port0_connector>;
> +};
> +
> +&usb_1_hsphy {
> +       vdda-pll-supply = <&vreg_l8a_0p91>;
> +       vdda18-supply = <&vreg_l14a_1p8>;
> +       vdda33-supply = <&vreg_l2a_2p3>;
> +
> +       status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> +       vdda-phy-supply = <&vreg_l8a_0p91>;
> +       vdda-pll-supply = <&vreg_l3a_1p2>;
> +
> +       status = "okay";
> +};
> --
> 2.42.0
>
>


-- 
With best wishes
Dmitry




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux