On 3/19/24 11:33, Krzysztof Kozlowski wrote:
On 17/03/2024 20:37, Ayush Singh wrote:
Add DT bindings for mikroBUS interface. MikroBUS is an open standard
developed by MikroElektronika for connecting add-on boards to
microcontrollers or microprocessors.
...
+title: mikroBUS add-on board socket
+
+maintainers:
+ - Ayush Singh <ayushdevel1325@xxxxxxxxx>
+
+properties:
+ compatible:
+ const: mikrobus-connector
+
+ pinctrl-0: true
+ pinctrl-1: true
+ pinctrl-2: true
+ pinctrl-3: true
+ pinctrl-4: true
+ pinctrl-5: true
+ pinctrl-6: true
+ pinctrl-7: true
+ pinctrl-8: true
+
+ pinctrl-names:
+ items:
+ - const: default
+ - const: pwm_default
+ - const: pwm_gpio
+ - const: uart_default
+ - const: uart_gpio
+ - const: i2c_default
+ - const: i2c_gpio
+ - const: spi_default
+ - const: spi_gpio
+
+ mikrobus-gpios:
+ minItems: 11
+ maxItems: 12
I don't see any of the issues resolved which I raised at v3. I think
Russell pointed that you do not have EEPROM and that some pins are
optional. You do not allow that.
So this patchset does not contain any EEPROM code. The bindings describe
mikroBUS connector and not mikroBUS addon board. While it is optional
for the mikroBUS addon board to not use sone pins (aka NC), the pins
still exist on the connector on the device side. It is not optional to
have pins in the host device.
Plus I don't see him being Cced but he had quite detailed look and
comments at your patchset, so *you are supposed to Cc* him.
I also do not see Rob's comments fully addressed.
Do not send next versions before resolving previous discusssion.
I apologize, I thought he was on the list by get_maintainers.pl, but it
seems I was mistaken. I will try to remember going forward.
+
+ i2c-adapter:
+ description: i2c adapter attached to the mikrobus socket.
+ $ref: /schemas/types.yaml#/definitions/phandle
+
+ spi-controller:
+ description: spi bus number of the spi-master attached to the mikrobus socket.
+ $ref: /schemas/types.yaml#/definitions/phandle
+
+ uart:
+ description: uart port attached to the mikrobus socket
+ $ref: /schemas/types.yaml#/definitions/phandle
+
+ pwms:
+ description: the pwm-controller corresponding to the mikroBUS PWM pin.
+ maxItems: 1
+
+ spi-cs:
+ description: spi chip-select numbers corresponding to the chip-selects on the mikrobus socket.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ - description: chip select corresponding to CS pin
+ - description: chip select corresponding to RST pin
+
+required:
+ - compatible
+ - pinctrl-0
+ - pinctrl-1
+ - pinctrl-2
+ - pinctrl-3
+ - pinctrl-4
+ - pinctrl-5
+ - pinctrl-6
+ - pinctrl-7
+ - pinctrl-8
+ - i2c-adapter
+ - spi-controller
+ - spi-cs
+ - uart
+ - pwms
+ - mikrobus-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ mikrobus {
+ compatible = "mikrobus-connector";
+ pinctrl-names = "default", "pwm_default", "pwm_gpio","uart_default", "uart_gpio", "i2c_default",
Please properly wrap your code according to Linux and DTS coding style
documents.
Best regards,
Krzysztof
Ayush Singh
