On Sun 17 Mar 2024 at 17:17, Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx> wrote:
> On 3/15/24 11:58, Jerome Brunet wrote:
>>
>> On Fri 15 Mar 2024 at 02:21, Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx> wrote:
>>
>>> Existing values were insufficient to produce accurate clock for audio
>>> devices. New values are safe and most suitable to produce 48000Hz sample
>>> rate.
>>
>> The hifi pll is not about 48k only. I see no reason to restrict the PLL
>> to a single setting.
>> > You've provided no justification why the PLL driver can't reach the same
>> setting for 48k. The setting below is just the crude part. the fine
>> tuning is done done with the frac parameter so I doubt this provides a
>> more accurate rate.
>>
>
> You are right, it is not about 48k only. However, there are two issues.
>
> First, indeed, I could just extend the range of multipliers to 1..255.
Why 1..255 ? This is not what I'm pointing out
According to the datasheet - the range is 32 - 64, as currently
set in the driver.
The change you have provided request a multipler of 128/5 = 25,6
If you put assigned-rate = 614400000 in DT, I see no reason can find the
same solution on its own.
> But I am unsure if hifi_pll is able to handle whole range of
> mulptipliers. The value 128 is taken from Amlogic's branch, and I am
> pretty sure that it works.
>
> Second, unfortunately frac parameter currently doesn't work. When frac
> is used enabling of hifi_pll fails in meson_clk_pll_wait_lock(). I see
> it when try to use 44100Hz and multipliers' range is set to 1..255. So,
> support of other rates than 48k requires extra effort.
Then your change is even more problematic because it certainly does not
disable frac ... which you say is broken.
That parameter should be removed with a proper comment explaining why
you are disabling it. That type a limitation / known issue should be
mentionned in your change.
>
>>>
>>> Signed-off-by: Jan Dakinevich <jan.dakinevich@xxxxxxxxxxxxxxxxx>
>>> ---
>>> drivers/clk/meson/a1-pll.c | 8 ++++----
>>> 1 file changed, 4 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
>>> index 4325e8a6a3ef..00e06d03445b 100644
>>> --- a/drivers/clk/meson/a1-pll.c
>>> +++ b/drivers/clk/meson/a1-pll.c
>>> @@ -74,9 +74,9 @@ static struct clk_regmap fixed_pll = {
>>> },
>>> };
>>>
>>> -static const struct pll_mult_range hifi_pll_mult_range = {
>>> - .min = 32,
>>> - .max = 64,
>>> +static const struct pll_params_table hifi_pll_params_table[] = {
>>> + PLL_PARAMS(128, 5),
>>> + { },
>>> };
>>>
>>> static const struct reg_sequence hifi_init_regs[] = {
>>> @@ -124,7 +124,7 @@ static struct clk_regmap hifi_pll = {
>>> .shift = 6,
>>> .width = 1,
>>> },
>>> - .range = &hifi_pll_mult_range,
>>> + .table = hifi_pll_params_table,
>>> .init_regs = hifi_init_regs,
>>> .init_count = ARRAY_SIZE(hifi_init_regs),
>>> },
>>
>>
--
Jerome
