Re: [PATCH/RFC v10 08/19] leds: Add support for max77693 mfd flash cell

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Jacek,

A few comments below.

On Fri, Jan 09, 2015 at 04:22:58PM +0100, Jacek Anaszewski wrote:
> This patch adds led-flash support to Maxim max77693 chipset.
> A device can be exposed to user space through LED subsystem
> sysfs interface. Device supports up to two leds which can
> work in flash and torch mode. The leds can be triggered
> externally or by software.
> 
> Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> Cc: Bryan Wu <cooloney@xxxxxxxxx>
> Cc: Richard Purdie <rpurdie@xxxxxxxxx>
> Cc: Lee Jones <lee.jones@xxxxxxxxxx>
> Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
> ---
>  drivers/leds/Kconfig         |   10 +
>  drivers/leds/Makefile        |    1 +
>  drivers/leds/leds-max77693.c | 1045 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 1056 insertions(+)
>  create mode 100644 drivers/leds/leds-max77693.c
> 
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index 95029df..ff9c21b 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -464,6 +464,16 @@ config LEDS_TCA6507
>  	  LED driver chips accessed via the I2C bus.
>  	  Driver support brightness control and hardware-assisted blinking.
>  
> +config LEDS_MAX77693
> +	tristate "LED support for MAX77693 Flash"
> +	depends on LEDS_CLASS_FLASH
> +	depends on MFD_MAX77693
> +	depends on OF
> +	help
> +	  This option enables support for the flash part of the MAX77693
> +	  multifunction device. It has build in control for two leds in flash
> +	  and torch mode.
> +
>  config LEDS_MAX8997
>  	tristate "LED support for MAX8997 PMIC"
>  	depends on LEDS_CLASS && MFD_MAX8997
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index cbba921..57ca62b 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -52,6 +52,7 @@ obj-$(CONFIG_LEDS_MC13783)		+= leds-mc13783.o
>  obj-$(CONFIG_LEDS_NS2)			+= leds-ns2.o
>  obj-$(CONFIG_LEDS_NETXBIG)		+= leds-netxbig.o
>  obj-$(CONFIG_LEDS_ASIC3)		+= leds-asic3.o
> +obj-$(CONFIG_LEDS_MAX77693)		+= leds-max77693.o
>  obj-$(CONFIG_LEDS_MAX8997)		+= leds-max8997.o
>  obj-$(CONFIG_LEDS_LM355x)		+= leds-lm355x.o
>  obj-$(CONFIG_LEDS_BLINKM)		+= leds-blinkm.o
> diff --git a/drivers/leds/leds-max77693.c b/drivers/leds/leds-max77693.c
> new file mode 100644
> index 0000000..3ba07c4
> --- /dev/null
> +++ b/drivers/leds/leds-max77693.c
> @@ -0,0 +1,1045 @@
> +/*
> + * LED Flash class driver for the flash cell of max77693 mfd.
> + *
> + *	Copyright (C) 2015, Samsung Electronics Co., Ltd.
> + *
> + *	Authors: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
> + *		 Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + */
> +
> +#include <asm/div64.h>
> +#include <linux/led-class-flash.h>
> +#include <linux/mfd/max77693.h>
> +#include <linux/mfd/max77693-private.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +
> +#define MODE_OFF		0
> +#define MODE_FLASH(a)		(1 << (a))
> +#define MODE_TORCH(a)		(1 << (2 + (a)))
> +#define MODE_FLASH_EXTERNAL(a)	(1 << (4 + (a)))
> +
> +#define MODE_FLASH_MASK		(MODE_FLASH(FLED1) | MODE_FLASH(FLED2) | \
> +				 MODE_FLASH_EXTERNAL(FLED1) | \
> +				 MODE_FLASH_EXTERNAL(FLED2))
> +#define MODE_TORCH_MASK		(MODE_TORCH(FLED1) | MODE_TORCH(FLED2))
> +
> +#define FLED1_IOUT		(1 << 0)
> +#define FLED2_IOUT		(1 << 1)
> +
> +enum max77693_fled {
> +	FLED1,
> +	FLED2,
> +};
> +
> +enum max77693_led_mode {
> +	FLASH,
> +	TORCH,
> +};
> +
> +struct max77693_sub_led {
> +	/* related FLED output identifier */
> +	int fled_id;
> +	/* related LED Flash class device */
> +	struct led_classdev_flash fled_cdev;
> +	/* assures led-triggers compatibility */
> +	struct work_struct work_brightness_set;
> +
> +	/* brightness cache */
> +	unsigned int torch_brightness;
> +	/* flash timeout cache */
> +	unsigned int flash_timeout;
> +};
> +
> +struct max77693_led_device {
> +	/* parent mfd regmap */
> +	struct regmap *regmap;
> +	/* platform device data */
> +	struct platform_device *pdev;
> +	/* configuration data for the device */
> +	struct max77693_led_config_data *cfg_data;

Where is this defined?

> +	/* secures access to the device */
> +	struct mutex lock;
> +
> +	/* sub led data */
> +	struct max77693_sub_led sub_leds[2];
> +
> +	/* current flash timeout cache */
> +	unsigned int current_flash_timeout;
> +	/* ITORCH register cache */
> +	u8 torch_iout_reg;
> +	/* mode of fled outputs */
> +	unsigned int mode_flags;
> +	/* recently strobed fled */
> +	int strobing_sub_led_id;
> +	/* bitmask of fled outputs use state (bit 0. - FLED1, bit 1. - FLED2) */
> +	u8 fled_mask;
> +	/* fled modes that can be set */
> +	u8 allowed_modes;
> +
> +	/* arrangement of current outputs */
> +	bool iout_joint;
> +};
> +
> +struct max77693_led_settings {
> +	struct led_flash_setting torch_brightness;
> +	struct led_flash_setting flash_brightness;
> +	struct led_flash_setting flash_timeout;
> +};
> +
> +static u8 max77693_led_iout_to_reg(u32 ua)
> +{
> +	if (ua < FLASH_IOUT_MIN)
> +		ua = FLASH_IOUT_MIN;
> +	return (ua - FLASH_IOUT_MIN) / FLASH_IOUT_STEP;
> +}
> +
> +static u8 max77693_flash_timeout_to_reg(u32 us)
> +{
> +	return (us - FLASH_TIMEOUT_MIN) / FLASH_TIMEOUT_STEP;
> +}
> +
> +static inline struct max77693_sub_led *flcdev_to_sub_led(
> +					struct led_classdev_flash *fled_cdev)
> +{
> +	return container_of(fled_cdev, struct max77693_sub_led, fled_cdev);
> +}
> +
> +static inline struct max77693_led_device *sub_led_to_led(
> +					struct max77693_sub_led *sub_led)
> +{
> +	return container_of(sub_led, struct max77693_led_device,
> +				sub_leds[sub_led->fled_id]);
> +}
> +
> +static inline u8 max77693_led_vsys_to_reg(u32 mv)
> +{
> +	return ((mv - MAX_FLASH1_VSYS_MIN) / MAX_FLASH1_VSYS_STEP) << 2;
> +}
> +
> +static inline u8 max77693_led_vout_to_reg(u32 mv)
> +{
> +	return (mv - FLASH_VOUT_MIN) / FLASH_VOUT_STEP + FLASH_VOUT_RMIN;
> +}
> +
> +static inline bool max77693_fled_used(struct max77693_led_device *led,
> +					 int fled_id)
> +{
> +	u8 fled_bit = (fled_id == FLED1) ? FLED1_IOUT : FLED2_IOUT;
> +
> +	return led->fled_mask & fled_bit;
> +}
> +
> +/* split composite current @i into two @iout according to @imax weights */

Do you still consider this as the right thing to do?

If there's a single LED driven by multiple outputs, what is the value
provided by board-specific current distribution between these outputs?

> +static void __max77693_calc_iout(u32 iout[2], u32 i, u32 imax[2])
> +{
> +	u64 t = i;
> +
> +	t *= imax[1];
> +	do_div(t, imax[0] + imax[1]);
> +
> +	iout[1] = (u32)t / FLASH_IOUT_STEP * FLASH_IOUT_STEP;
> +	iout[0] = i - iout[1];
> +}
> +
> +static int max77693_set_mode(struct max77693_led_device *led, u8 mode)
> +{
> +	struct regmap *rmap = led->regmap;
> +	int ret, v = 0, i;
> +
> +	for (i = FLED1; i <= FLED2; ++i) {
> +		if (mode & MODE_TORCH(i))
> +			v |= FLASH_EN_ON << TORCH_EN_SHIFT(i);
> +
> +		if (mode & MODE_FLASH(i)) {
> +			v |= FLASH_EN_ON << FLASH_EN_SHIFT(i);
> +		} else if (mode & MODE_FLASH_EXTERNAL(i)) {
> +			v |= FLASH_EN_FLASH << FLASH_EN_SHIFT(i);
> +			/*
> +			 * Enable hw triggering also for torch mode, as some
> +			 * camera sensors use torch led to fathom ambient light
> +			 * conditions before strobing the flash.
> +			 */
> +			v |= FLASH_EN_TORCH << TORCH_EN_SHIFT(i);
> +		}
> +	}
> +
> +	/* Reset the register only prior setting flash modes */
> +	if (mode & ~(MODE_TORCH(FLED1) | MODE_TORCH(FLED2))) {
> +		ret = regmap_write(rmap, MAX77693_LED_REG_FLASH_EN, 0);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	return regmap_write(rmap, MAX77693_LED_REG_FLASH_EN, v);
> +}
> +
> +static void max77693_set_sync_strobe(struct max77693_led_device *led,
> +					u8 *mode)
> +{
> +	struct max77693_sub_led *sub_leds = led->sub_leds;
> +	struct led_classdev_flash *fled_cdev;
> +	u8 m = *mode;
> +
> +	if (led->iout_joint)
> +		return;
> +
> +	/* Check if the other sub-led wants to be strobed simultaneously. */
> +	if (m & (MODE_FLASH(FLED1) | MODE_FLASH_EXTERNAL(FLED1))) {
> +		fled_cdev = &sub_leds[FLED2].fled_cdev;
> +		if (fled_cdev->sync_led_id)
> +			m |= m << 1;
> +	} else if (m & (MODE_FLASH(FLED2) | MODE_FLASH_EXTERNAL(FLED2))) {
> +		fled_cdev = &sub_leds[FLED1].fled_cdev;
> +		if (fled_cdev->sync_led_id)
> +			m |= m >> 1;
> +	}
> +
> +	*mode = m;
> +}
> +
> +static int max77693_add_mode(struct max77693_led_device *led, u8 mode)
> +{
> +	int i, ret;
> +
> +	mode &= led->allowed_modes;
> +
> +	/*
> +	 * Torch mode once enabled remains active until turned off. If the FLED2
> +	 * output isn't to be disabled check if the torch mode to be set isn't
> +	 * already activated and avoid re-setting it.
> +	 */
> +	if ((!(mode ^ led->mode_flags)) & MODE_TORCH(FLED2)) {
> +		for (i = FLED1; i <= FLED2; ++i)
> +			if ((mode & MODE_TORCH(i)) &&
> +			    (led->mode_flags & MODE_TORCH(i)))
> +				return 0;
> +	}
> +
> +	/* Span the mode on FLED2 for joint iouts case */
> +	if (led->iout_joint)
> +		mode |= (mode << 1);
> +
> +	/* Span the flash mode on the other led if it is to be synchronized */
> +	max77693_set_sync_strobe(led, &mode);
> +
> +	/*
> +	 * FLASH_EXTERNAL mode activates FLASHEN and TORCHEN pins in the device.
> +	 * The related register bits fields interfere with SW triggerred modes,
> +	 * thus clear them to ensure proper device configuration.
> +	 */
> +	for (i = FLED1; i <= FLED2; ++i)
> +		if (mode & MODE_FLASH_EXTERNAL(i))
> +			led->mode_flags &= (~MODE_TORCH(i) & ~MODE_FLASH(i));
> +
> +	led->mode_flags |= mode;
> +	led->mode_flags &= led->allowed_modes;
> +
> +	ret = max77693_set_mode(led, led->mode_flags);
> +	if (ret < 0)
> +		return ret;
> +
> +	/*
> +	 * Clear flash mode flag after setting the mode to avoid spurious flash
> +	 * strobing on each subsequent torch mode setting.
> +	 */
> +	if (mode & MODE_FLASH_MASK)
> +		led->mode_flags &= ~mode;
> +
> +	return ret;
> +}
> +
> +static int max77693_clear_mode(struct max77693_led_device *led,
> +				u8 mode)
> +{
> +	int ret;
> +
> +	if (led->iout_joint)
> +		/* Clear mode also on FLED2 for joint iouts case */
> +		mode |= (mode << 1);
> +	else
> +		/*
> +		 * Clear a flash mode on the other led
> +		 * if it is to be synchronized.
> +		 */
> +		max77693_set_sync_strobe(led, &mode);
> +
> +	led->mode_flags &= ~mode;
> +
> +	ret = max77693_set_mode(led, led->mode_flags);
> +
> +	return ret;
> +}
> +
> +static void max77693_calc_iout(struct max77693_led_device *led, int fled_id,
> +				u32 iout[2], u32 micro_amp, u32 iout_max[2],
> +				enum max77693_led_mode mode)
> +{
> +	u8 blocked_modes;
> +
> +	if (fled_id == FLED1) {
> +		if (led->iout_joint) {
> +			/*
> +			 * FLED2 must not be turned on to get
> +			 * 15625 uA of total current.
> +			 */
> +			if (micro_amp == FLASH_IOUT_MIN) {
> +				if (mode == FLASH)
> +					blocked_modes =
> +						MODE_FLASH(FLED2) |
> +						MODE_FLASH_EXTERNAL(FLED2);
> +				else
> +					blocked_modes = MODE_TORCH(FLED2);
> +
> +				led->allowed_modes &= ~blocked_modes;
> +			}
> +		} else {
> +			/*
> +			 * Preclude splitting current to FLED2 if we
> +			 * are driving two separate leds.
> +			 */
> +			iout_max[FLED2] = 0;
> +		}
> +		__max77693_calc_iout(iout, micro_amp, iout_max);
> +	} else if (fled_id == FLED2) {
> +		/*
> +		 * Preclude splitting current to FLED1 if we
> +		 * are driving two separate leds.
> +		 */
> +		iout_max[FLED1] = 0;
> +		__max77693_calc_iout(iout, micro_amp, iout_max);
> +	}
> +}
> +
> +static int max77693_set_torch_current(struct max77693_led_device *led,
> +				int fled_id, u32 micro_amp)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	struct regmap *rmap = led->regmap;
> +	u32 iout[2], iout_max[2];
> +	u8 iout1_reg = 0, iout2_reg = 0;
> +
> +	iout_max[FLED1] = cfg->iout_torch[FLED1];
> +	iout_max[FLED2] = cfg->iout_torch[FLED2];
> +
> +	led->allowed_modes |= MODE_TORCH_MASK;
> +
> +	max77693_calc_iout(led, fled_id, iout, micro_amp, iout_max,

Could you use cfg->iout_torch directly?

> +				TORCH);
> +
> +	if (fled_id == FLED1 || led->iout_joint) {
> +		iout1_reg = max77693_led_iout_to_reg(iout[FLED1]);
> +		led->torch_iout_reg &= 0xf0;

I think it'd be cleaner to use register bit names and led-specific shift
here. Up to you.

> +	}
> +	if (fled_id == FLED2 || led->iout_joint) {
> +		iout2_reg = max77693_led_iout_to_reg(iout[FLED2]);
> +		led->torch_iout_reg &= 0x0f;
> +	}
> +
> +	led->torch_iout_reg |= ((iout1_reg << TORCH_IOUT1_SHIFT) |
> +				(iout2_reg << TORCH_IOUT2_SHIFT));
> +
> +	return regmap_write(rmap, MAX77693_LED_REG_ITORCH,
> +						led->torch_iout_reg);
> +}
> +
> +static int max77693_set_flash_current(struct max77693_led_device *led,
> +					int fled_id,
> +					u32 micro_amp)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	struct regmap *rmap = led->regmap;
> +	u32 iout[2], iout_max[2];
> +	u8 iout1_reg, iout2_reg;
> +	int ret = -EINVAL;
> +
> +	iout_max[FLED1] = cfg->iout_flash[FLED1];
> +	iout_max[FLED2] = cfg->iout_flash[FLED2];
> +
> +	led->allowed_modes |= MODE_FLASH_MASK;
> +
> +	max77693_calc_iout(led, fled_id, iout, micro_amp, iout_max,
> +				FLASH);
> +
> +	if (fled_id == FLED1 || led->iout_joint) {
> +		iout1_reg = max77693_led_iout_to_reg(iout[FLED1]);
> +		ret = regmap_write(rmap, MAX77693_LED_REG_IFLASH1,
> +							iout1_reg);
> +		if (ret < 0)
> +			return ret;
> +	}
> +	if (fled_id == FLED2 || led->iout_joint) {
> +		iout2_reg = max77693_led_iout_to_reg(iout[FLED2]);
> +		ret = regmap_write(rmap, MAX77693_LED_REG_IFLASH2,
> +							iout2_reg);
> +	}
> +
> +	return ret;
> +}
> +
> +static int max77693_set_timeout(struct max77693_led_device *led, u32 microsec)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	struct regmap *rmap = led->regmap;
> +	u8 v;
> +	int ret;
> +
> +	v = max77693_flash_timeout_to_reg(microsec);
> +
> +	if (cfg->trigger_type == MAX77693_LED_TRIG_TYPE_LEVEL)
> +		v |= FLASH_TMR_LEVEL;
> +
> +	ret = regmap_write(rmap, MAX77693_LED_REG_FLASH_TIMER, v);
> +	if (ret < 0)
> +		return ret;
> +
> +	led->current_flash_timeout = microsec;
> +
> +	return 0;
> +}
> +
> +static int max77693_strobe_status_get(struct max77693_led_device *led,
> +					bool *state)
> +{
> +	struct regmap *rmap = led->regmap;
> +	unsigned int v;
> +	int ret;
> +
> +	ret = regmap_read(rmap, MAX77693_LED_REG_FLASH_STATUS, &v);
> +	if (ret < 0)
> +		return ret;
> +
> +	*state = v & FLASH_STATUS_FLASH_ON;
> +
> +	return ret;
> +}
> +
> +static int max77693_int_flag_get(struct max77693_led_device *led,
> +					unsigned int *v)
> +{
> +	struct regmap *rmap = led->regmap;
> +
> +	return regmap_read(rmap, MAX77693_LED_REG_FLASH_INT, v);
> +}
> +
> +static int max77693_setup(struct max77693_led_device *led)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	struct regmap *rmap = led->regmap;
> +	int i, first_led, last_led, ret;
> +	u32 max_flash_curr[2];
> +	u8 v;
> +
> +	/*
> +	 * Initialize only flash current. Torch current doesn't
> +	 * require initialization as ITORCH register is written with
> +	 * new value each time brightness_set op is called.
> +	 */
> +	if (led->iout_joint) {
> +		first_led = FLED1;
> +		last_led = FLED1;
> +		max_flash_curr[FLED1] = cfg->iout_flash[FLED1] +
> +					cfg->iout_flash[FLED2];
> +	} else {
> +		first_led = max77693_fled_used(led, FLED1) ? FLED1 : FLED2;
> +		last_led = led->cfg_data->num_leds == 2 ? FLED2 : first_led;
> +		max_flash_curr[FLED1] = cfg->iout_flash[FLED1];
> +		max_flash_curr[FLED2] = cfg->iout_flash[FLED2];
> +	}
> +
> +	for (i = first_led; i <= last_led; ++i) {
> +		ret = max77693_set_flash_current(led, i,
> +					max_flash_curr[i]);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	v = TORCH_TMR_NO_TIMER | MAX77693_LED_TRIG_TYPE_LEVEL;
> +	ret = regmap_write(rmap, MAX77693_LED_REG_ITORCHTIMER, v);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* initially set FLED1 timeout */
> +	ret = max77693_set_timeout(led, cfg->flash_timeout[FLED1]);
> +	if (ret < 0)
> +		return ret;
> +
> +	if (cfg->low_vsys > 0)
> +		v = max77693_led_vsys_to_reg(cfg->low_vsys) |
> +						MAX_FLASH1_MAX_FL_EN;
> +	else
> +		v = 0;
> +
> +	ret = regmap_write(rmap, MAX77693_LED_REG_MAX_FLASH1, v);
> +	if (ret < 0)
> +		return ret;
> +	ret = regmap_write(rmap, MAX77693_LED_REG_MAX_FLASH2, 0);
> +	if (ret < 0)
> +		return ret;
> +
> +	if (cfg->boost_mode == MAX77693_LED_BOOST_FIXED)
> +		v = FLASH_BOOST_FIXED;
> +	else
> +		v = cfg->boost_mode | cfg->boost_mode << 1;
> +
> +	if (max77693_fled_used(led, FLED1) && max77693_fled_used(led, FLED2))
> +		v |= FLASH_BOOST_LEDNUM_2;
> +
> +	ret = regmap_write(rmap, MAX77693_LED_REG_VOUT_CNTL, v);
> +	if (ret < 0)
> +		return ret;
> +
> +	v = max77693_led_vout_to_reg(cfg->boost_vout);
> +	ret = regmap_write(rmap, MAX77693_LED_REG_VOUT_FLASH1, v);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Allow all modes on both fled outputs */
> +	led->allowed_modes = MODE_FLASH_MASK | MODE_TORCH_MASK;
> +
> +	return max77693_set_mode(led, MODE_OFF);
> +}
> +
> +static int __max77693_led_brightness_set(struct max77693_led_device *led,
> +					int fled_id, enum led_brightness value)
> +{
> +	int ret;
> +
> +	mutex_lock(&led->lock);
> +
> +	if (value == 0) {
> +		ret = max77693_clear_mode(led, MODE_TORCH(fled_id));
> +		if (ret < 0)
> +			dev_dbg(&led->pdev->dev,
> +				"Failed to clear torch mode (%d)\n",
> +				ret);
> +		goto unlock;
> +	}
> +
> +	ret = max77693_set_torch_current(led, fled_id, value * TORCH_IOUT_STEP);
> +	if (ret < 0) {
> +		dev_dbg(&led->pdev->dev,
> +			"Failed to set torch current (%d)\n",
> +			ret);
> +		goto unlock;
> +	}
> +
> +	ret = max77693_add_mode(led, MODE_TORCH(fled_id));
> +	if (ret < 0)
> +		dev_dbg(&led->pdev->dev,
> +			"Failed to set torch mode (%d)\n",
> +			ret);
> +unlock:
> +	mutex_unlock(&led->lock);
> +	return ret;
> +}
> +
> +static void max77693_led_brightness_set_work(
> +					struct work_struct *work)
> +{
> +	struct max77693_sub_led *sub_led =
> +			container_of(work, struct max77693_sub_led,
> +					work_brightness_set);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +
> +	__max77693_led_brightness_set(led, sub_led->fled_id,
> +				sub_led->torch_brightness);
> +}
> +
> +/* LED subsystem callbacks */
> +
> +static int max77693_led_brightness_set_sync(
> +				struct led_classdev *led_cdev,
> +				enum led_brightness value)
> +{
> +	struct led_classdev_flash *fled_cdev = lcdev_to_flcdev(led_cdev);
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +
> +	return __max77693_led_brightness_set(led, sub_led->fled_id, value);
> +}
> +
> +static void max77693_led_brightness_set(
> +				struct led_classdev *led_cdev,
> +				enum led_brightness value)
> +{
> +	struct led_classdev_flash *fled_cdev = lcdev_to_flcdev(led_cdev);
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +
> +	sub_led->torch_brightness = value;
> +	schedule_work(&sub_led->work_brightness_set);
> +}
> +
> +static int max77693_led_flash_brightness_set(
> +				struct led_classdev_flash *fled_cdev,
> +				u32 brightness)
> +{
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +	int ret;
> +
> +	mutex_lock(&led->lock);
> +	ret = max77693_set_flash_current(led, sub_led->fled_id, brightness);
> +	mutex_unlock(&led->lock);
> +
> +	return ret;
> +}
> +
> +static int max77693_led_flash_strobe_set(
> +				struct led_classdev_flash *fled_cdev,
> +				bool state)
> +{
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +	int fled_id = sub_led->fled_id;
> +	int ret;
> +
> +	mutex_lock(&led->lock);
> +
> +	if (!state) {
> +		ret = max77693_clear_mode(led, MODE_FLASH(fled_id));
> +		goto unlock;
> +	}
> +
> +	if (sub_led->flash_timeout != led->current_flash_timeout) {
> +		ret = max77693_set_timeout(led, sub_led->flash_timeout);
> +		if (ret < 0)
> +			goto unlock;
> +	}
> +
> +	led->strobing_sub_led_id = fled_id;
> +
> +	ret = max77693_add_mode(led, MODE_FLASH(fled_id));
> +
> +unlock:
> +	mutex_unlock(&led->lock);
> +	return ret;
> +}
> +
> +static int max77693_led_flash_fault_get(
> +				struct led_classdev_flash *fled_cdev,
> +				u32 *fault)
> +{
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +	unsigned int v;
> +	int ret;
> +
> +	ret = max77693_int_flag_get(led, &v);
> +	if (ret < 0)
> +		return ret;
> +
> +	*fault = 0;
> +
> +	if (v & ((sub_led->fled_id == FLED1) ? FLASH_INT_FLED1_OPEN :
> +					       FLASH_INT_FLED2_OPEN))
> +		*fault |= LED_FAULT_OVER_VOLTAGE;
> +	if (v & ((sub_led->fled_id == FLED1) ? FLASH_INT_FLED1_SHORT :
> +					       FLASH_INT_FLED2_SHORT))
> +		*fault |= LED_FAULT_SHORT_CIRCUIT;
> +	if (v & FLASH_INT_OVER_CURRENT)
> +		*fault |= LED_FAULT_OVER_CURRENT;
> +
> +	return 0;
> +}
> +
> +static int max77693_led_flash_strobe_get(
> +				struct led_classdev_flash *fled_cdev,
> +				bool *state)
> +{
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +	int ret;
> +
> +	if (!state)
> +		return -EINVAL;
> +
> +	mutex_lock(&led->lock);
> +
> +	ret = max77693_strobe_status_get(led, state);
> +
> +	*state = !!(*state && (led->strobing_sub_led_id == sub_led->fled_id));
> +
> +
> +	mutex_unlock(&led->lock);
> +
> +	return ret;
> +}
> +
> +static int max77693_led_flash_timeout_set(
> +				struct led_classdev_flash *fled_cdev,
> +				u32 timeout)
> +{
> +	struct max77693_sub_led *sub_led = flcdev_to_sub_led(fled_cdev);
> +	struct max77693_led_device *led = sub_led_to_led(sub_led);
> +
> +	mutex_lock(&led->lock);
> +	sub_led->flash_timeout = timeout;
> +	mutex_unlock(&led->lock);
> +
> +	return 0;
> +}
> +
> +static int max77693_led_parse_dt(struct max77693_led_device *led,
> +				 struct device_node *node)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	struct max77693_sub_led *sub_leds = led->sub_leds;
> +	struct device *dev = &led->pdev->dev;
> +	struct device_node *child_node;
> +	u32 led_sources[2];
> +	int fled_id, ret;
> +
> +	of_property_read_u32(node, "maxim,trigger-type", &cfg->trigger_type);
> +	of_property_read_u32(node, "maxim,boost-mode", &cfg->boost_mode);
> +	of_property_read_u32(node, "maxim,boost-vout", &cfg->boost_vout);
> +	of_property_read_u32(node, "maxim,vsys-min", &cfg->low_vsys);
> +
> +	for_each_available_child_of_node(node, child_node) {
> +		ret = of_property_read_u32_array(child_node, "led-sources",
> +							led_sources, 2);
> +		if (ret < 0) {
> +			dev_err(dev,
> +				"Error reading \"led-sources\" DT property\n");
> +			return ret;
> +		}
> +
> +		if (led_sources[0] && led_sources[1]) {
> +			fled_id = FLED1;
> +			led->fled_mask = FLED1_IOUT | FLED2_IOUT;
> +		} else if (led_sources[0] && !led_sources[1]) {
> +			fled_id = FLED1;
> +			led->fled_mask |= FLED1_IOUT;
> +		} else if (!led_sources[0] && led_sources[1]) {
> +			fled_id = FLED2;
> +			led->fled_mask |= FLED2_IOUT;
> +		} else {
> +			dev_err(dev,
> +				"Wrong \"led-sources\" DT property value\n");
> +			return -EINVAL;
> +		}
> +
> +		sub_leds[fled_id].fled_id = fled_id;
> +
> +		ret = of_property_read_string(child_node, "label",
> +					(const char **) &cfg->label[fled_id]);
> +		if (ret < 0) {
> +			dev_err(dev, "Error reading \"label\" DT property\n");
> +			return ret;
> +		}
> +
> +		of_property_read_u32(child_node, "max-microamp",
> +						&cfg->iout_torch[fled_id]);
> +		of_property_read_u32(child_node, "flash-max-microamp",
> +						&cfg->iout_flash[fled_id]);
> +		of_property_read_u32(child_node, "flash-timeout-us",
> +						&cfg->flash_timeout[fled_id]);
> +
> +		if (++led->cfg_data->num_leds == 2 ||
> +		    (max77693_fled_used(led, FLED1) &&
> +		     max77693_fled_used(led, FLED2)))
> +			break;
> +	}
> +
> +	return 0;
> +}
> +
> +static void clamp_align(u32 *v, u32 min, u32 max, u32 step)
> +{
> +	*v = clamp_val(*v, min, max);
> +	if (step > 1)
> +		*v = (*v - min) / step * step + min;
> +}
> +
> +static void max77693_led_validate_configuration(struct max77693_led_device *led)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	int i;
> +
> +	if (led->cfg_data->num_leds == 1 &&
> +	    max77693_fled_used(led, FLED1) && max77693_fled_used(led, FLED2))
> +		led->iout_joint = true;
> +
> +	cfg->boost_mode = clamp_val(cfg->boost_mode, MAX77693_LED_BOOST_NONE,
> +			    MAX77693_LED_BOOST_FIXED);
> +
> +	/* Boost must be enabled if both current outputs are used */
> +	if ((cfg->boost_mode == MAX77693_LED_BOOST_NONE) && led->iout_joint)
> +		cfg->boost_mode = MAX77693_LED_BOOST_FIXED;
> +
> +	/* Split max current settings to both outputs in case of joint leds */
> +	if (led->iout_joint) {
> +		cfg->iout_torch[FLED1] /= 2;
> +		cfg->iout_torch[FLED2] = cfg->iout_torch[FLED1];
> +		cfg->iout_flash[FLED1] /= 2;
> +		cfg->iout_flash[FLED2] = cfg->iout_flash[FLED1];
> +	}
> +
> +	for (i = FLED1; i <= FLED2; ++i) {
> +		if (max77693_fled_used(led, i)) {
> +			clamp_align(&cfg->iout_torch[i], TORCH_IOUT_MIN,
> +					TORCH_IOUT_MAX, TORCH_IOUT_STEP);
> +			clamp_align(&cfg->iout_flash[i], FLASH_IOUT_MIN,
> +					cfg->boost_mode ? FLASH_IOUT_MAX_2LEDS :
> +							FLASH_IOUT_MAX_1LED,
> +					FLASH_IOUT_STEP);
> +		} else {
> +			cfg->iout_torch[i] = cfg->iout_flash[i] = 0;
> +		}
> +	}
> +
> +	for (i = 0; i < ARRAY_SIZE(cfg->flash_timeout); ++i)
> +		clamp_align(&cfg->flash_timeout[i], FLASH_TIMEOUT_MIN,
> +				FLASH_TIMEOUT_MAX, FLASH_TIMEOUT_STEP);
> +
> +	cfg->trigger_type = clamp_val(cfg->trigger_type,
> +					MAX77693_LED_TRIG_TYPE_EDGE,
> +					MAX77693_LED_TRIG_TYPE_LEVEL);
> +
> +	clamp_align(&cfg->boost_vout, FLASH_VOUT_MIN, FLASH_VOUT_MAX,
> +							FLASH_VOUT_STEP);
> +
> +	if (cfg->low_vsys)
> +		clamp_align(&cfg->low_vsys, MAX_FLASH1_VSYS_MIN,
> +				MAX_FLASH1_VSYS_MAX, MAX_FLASH1_VSYS_STEP);
> +}
> +
> +static int max77693_led_get_configuration(struct max77693_led_device *led)
> +{
> +	struct device *dev = &led->pdev->dev;
> +	int ret;
> +
> +	if (!dev->of_node)
> +		return -EINVAL;
> +
> +	led->cfg_data = devm_kzalloc(dev, sizeof(*led->cfg_data), GFP_KERNEL);
> +	if (!led->cfg_data)
> +		return -ENOMEM;
> +
> +	ret = max77693_led_parse_dt(led, dev->of_node);
> +	if (ret < 0)
> +		return ret;
> +
> +	max77693_led_validate_configuration(led);
> +
> +	return 0;
> +}
> +
> +static const struct led_flash_ops flash_ops = {
> +	.flash_brightness_set	= max77693_led_flash_brightness_set,
> +	.strobe_set		= max77693_led_flash_strobe_set,
> +	.strobe_get		= max77693_led_flash_strobe_get,
> +	.timeout_set		= max77693_led_flash_timeout_set,
> +	.fault_get		= max77693_led_flash_fault_get,
> +};
> +
> +static void max77693_init_flash_settings(struct max77693_led_device *led,
> +					 struct max77693_led_settings *s,
> +					 int fled_id)
> +{
> +	struct max77693_led_config_data *cfg = led->cfg_data;
> +	struct led_flash_setting *setting;
> +
> +	/* Init torch intensity setting */
> +	setting = &s->torch_brightness;
> +	setting->min = TORCH_IOUT_MIN;
> +	setting->max = cfg->iout_torch[fled_id];
> +	setting->max = led->iout_joint ?
> +			cfg->iout_torch[FLED1] + cfg->iout_torch[FLED2] :
> +			cfg->iout_torch[fled_id];
> +	setting->step = TORCH_IOUT_STEP;
> +	setting->val = setting->max;
> +
> +	/* Init flash intensity setting */
> +	setting = &s->flash_brightness;
> +	setting->min = FLASH_IOUT_MIN;
> +	setting->max = led->iout_joint ?
> +			cfg->iout_flash[FLED1] + cfg->iout_flash[FLED2] :
> +			cfg->iout_flash[fled_id];
> +	setting->step = FLASH_IOUT_STEP;
> +	setting->val = setting->max;
> +
> +	/* Init flash timeout setting */
> +	setting = &s->flash_timeout;
> +	setting->min = FLASH_TIMEOUT_MIN;
> +	setting->max = cfg->flash_timeout[fled_id];
> +	setting->step = FLASH_TIMEOUT_STEP;
> +	setting->val = setting->max;
> +}
> +
> +static int max77693_set_available_sync_led(struct max77693_led_device *led,
> +						int fled_id)
> +{
> +	struct max77693_sub_led *sub_led = &led->sub_leds[fled_id];
> +	struct led_classdev_flash *fled_cdev = &sub_led->fled_cdev;
> +
> +	fled_cdev->sync_leds = devm_kzalloc(&led->pdev->dev, sizeof(fled_cdev),
> +					GFP_KERNEL);
> +	if (!fled_cdev->sync_leds)
> +		return -ENOMEM;
> +
> +	fled_cdev->sync_leds[0] = &led->sub_leds[!fled_id].fled_cdev;
> +	fled_cdev->num_sync_leds = 1;
> +
> +	return 0;
> +}
> +
> +static void max77693_init_fled_cdev(struct max77693_led_device *led,
> +					int fled_id)
> +{
> +	struct led_classdev_flash *fled_cdev;
> +	struct led_classdev *led_cdev;
> +	struct max77693_sub_led *sub_led = &led->sub_leds[fled_id];
> +	struct max77693_led_settings settings;
> +
> +	/* Initialize flash settings */
> +	max77693_init_flash_settings(led, &settings, fled_id);
> +
> +	/* Initialize LED Flash class device */
> +	fled_cdev = &sub_led->fled_cdev;
> +	fled_cdev->ops = &flash_ops;
> +	led_cdev = &fled_cdev->led_cdev;
> +	led_cdev->name = led->cfg_data->label[fled_id];
> +	led_cdev->brightness_set = max77693_led_brightness_set;
> +	led_cdev->brightness_set_sync = max77693_led_brightness_set_sync;
> +	INIT_WORK(&sub_led->work_brightness_set,
> +			max77693_led_brightness_set_work);
> +
> +	led_cdev->max_brightness = settings.torch_brightness.val /
> +					TORCH_IOUT_STEP;
> +	led_cdev->flags |= LED_DEV_CAP_FLASH;
> +	if (led->cfg_data->num_leds == 2)
> +		led_cdev->flags |= LED_DEV_CAP_SYNC_STROBE;
> +
> +	fled_cdev->brightness = settings.flash_brightness;
> +	fled_cdev->timeout = settings.flash_timeout;
> +	sub_led->flash_timeout = fled_cdev->timeout.val;
> +}
> +
> +static int max77693_led_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct max77693_dev *iodev = dev_get_drvdata(dev->parent);
> +	struct max77693_led_device *led;
> +	struct max77693_sub_led *sub_leds;
> +	int init_fled_cdev[2], i, ret;
> +
> +	led = devm_kzalloc(dev, sizeof(*led), GFP_KERNEL);
> +	if (!led)
> +		return -ENOMEM;
> +
> +	led->pdev = pdev;
> +	led->regmap = iodev->regmap;
> +	sub_leds = led->sub_leds;
> +
> +	platform_set_drvdata(pdev, led);
> +	ret = max77693_led_get_configuration(led);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = max77693_setup(led);
> +	if (ret < 0)
> +		return ret;
> +
> +	init_fled_cdev[FLED1] =
> +			led->iout_joint || max77693_fled_used(led, FLED1);
> +	init_fled_cdev[FLED2] =
> +			!led->iout_joint && max77693_fled_used(led, FLED2);
> +
> +	/* Initialize LED Flash class device(s) */
> +	for (i = FLED1; i <= FLED2; ++i)
> +		if (init_fled_cdev[i])
> +			max77693_init_fled_cdev(led, i);
> +
> +	/* Setup sub-leds available for flash strobe synchronization */
> +	if (led->cfg_data->num_leds == 2) {
> +		for (i = FLED1; i <= FLED2; ++i) {
> +			ret = max77693_set_available_sync_led(led, i);
> +			if (ret < 0)
> +				return ret;
> +		}
> +	}
> +
> +	mutex_init(&led->lock);
> +
> +	/* Register LED Flash class device(s) */
> +	for (i = FLED1; i <= FLED2; ++i) {
> +		if (init_fled_cdev[i]) {

if (!...)
	continue;

The rest of the loop would look nicer this way I think. Up to you.

> +			ret = led_classdev_flash_register(dev,
> +							&sub_leds[i].fled_cdev);
> +			if (ret < 0) {
> +				/*
> +				 * At this moment FLED1 might have been already
> +				 * registered and it needs to be released.
> +				 */
> +				if (i == FLED2)
> +					goto err_register_led2;
> +				else
> +					goto err_register_led1;
> +			}
> +		}
> +	}
> +
> +
> +	return 0;
> +
> +err_register_led2:
> +	/* It is possible than only FLED2 was to be registered */
> +	if (!init_fled_cdev[FLED1])
> +		goto err_register_led1;
> +	led_classdev_flash_unregister(&sub_leds[FLED1].fled_cdev);
> +err_register_led1:
> +	mutex_destroy(&led->lock);
> +
> +	return ret;
> +}
> +
> +static int max77693_led_remove(struct platform_device *pdev)
> +{
> +	struct max77693_led_device *led = platform_get_drvdata(pdev);
> +	struct max77693_sub_led *sub_leds = led->sub_leds;
> +
> +	if (led->iout_joint || max77693_fled_used(led, FLED1)) {
> +		led_classdev_flash_unregister(&sub_leds[FLED1].fled_cdev);
> +		cancel_work_sync(&sub_leds[FLED1].work_brightness_set);
> +	}
> +
> +	if (!led->iout_joint && max77693_fled_used(led, FLED2)) {
> +		led_classdev_flash_unregister(&sub_leds[FLED2].fled_cdev);
> +		cancel_work_sync(&sub_leds[FLED2].work_brightness_set);
> +	}
> +
> +	mutex_destroy(&led->lock);
> +
> +	return 0;
> +}
> +
> +static struct of_device_id max77693_led_dt_match[] = {
> +	{.compatible = "maxim,max77693-led"},
> +	{},
> +};
> +
> +static struct platform_driver max77693_led_driver = {
> +	.probe		= max77693_led_probe,
> +	.remove		= max77693_led_remove,
> +	.driver		= {
> +		.name	= "max77693-led",
> +		.owner	= THIS_MODULE,
> +		.of_match_table = max77693_led_dt_match,
> +	},
> +};
> +
> +module_platform_driver(max77693_led_driver);
> +
> +MODULE_AUTHOR("Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>");
> +MODULE_AUTHOR("Andrzej Hajda <a.hajda@xxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Maxim MAX77693 led flash driver");
> +MODULE_LICENSE("GPL v2");

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@xxxxxx	XMPP: sailus@xxxxxxxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux