Re: [PATCH] media: i2c: add support for omnivision's ov2659 sensor

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Prabhakar,

Thank you for the patch. Here's a partial review.

On Thursday 15 January 2015 23:39:23 Lad, Prabhakar wrote:
> From: Benoit Parrot <bparrot@xxxxxx>
> 
> this patch adds support for omnivision's ov2659
> sensor.
> 
> Signed-off-by: Benoit Parrot <bparrot@xxxxxx>
> Signed-off-by: Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx>
> ---
>  .../devicetree/bindings/media/i2c/ov2659.txt       |   33 +
>  .../devicetree/bindings/vendor-prefixes.txt        |    1 +
>  MAINTAINERS                                        |   10 +
>  drivers/media/i2c/Kconfig                          |   11 +
>  drivers/media/i2c/Makefile                         |    1 +
>  drivers/media/i2c/ov2659.c                         | 1623 +++++++++++++++++
>  include/media/ov2659.h                             |   33 +
>  7 files changed, 1712 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov2659.txt
>  create mode 100644 drivers/media/i2c/ov2659.c
>  create mode 100644 include/media/ov2659.h
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt
> b/Documentation/devicetree/bindings/media/i2c/ov2659.txt new file mode
> 100644
> index 0000000..fc49f44
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
> @@ -0,0 +1,33 @@
> +* OV2659 1/5-Inch 2Mp SOC Camera
> +
> +The OV2659 is a 1/5-inch SOC camera, with an active array size of 1632H x
> 1212V.
> +It is programmable through a SCCB.
> +
> +Required Properties:
> +- compatible: Must be "ovt,ov2659"
> +
> +- reg: I2C slave address
> +
> +- clock-frequency: Input clock frequency.
> +
> +For further reading on port node refer to
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +
> +	i2c0@1c22000 {
> +		...
> +		...
> +		 ov2659@30 {
> +			compatible = "ovt,ov2659";
> +			reg = <0x30>;
> +
> +			port {
> +				ov2659_0: endpoint {
> +					clock-frequency = <12000000>;
> +					remote-endpoint = <&vpfe_ep>;
> +				};
> +			};
> +		};
> +		...
> +	};

[snip]

> diff --git a/drivers/media/i2c/ov2659.c b/drivers/media/i2c/ov2659.c
> new file mode 100644
> index 0000000..ce8ec8d
> --- /dev/null
> +++ b/drivers/media/i2c/ov2659.c
> @@ -0,0 +1,1623 @@

[snip]

> +static int debug;
> +module_param(debug, int, 0644);
> +MODULE_PARM_DESC(debug, "Debug level (0-2)");

The debug parameter is printed in the probe function and then unused. You can 
remove it.

[snip]

> +struct ov2659 {
> +	struct v4l2_subdev sd;
> +	struct media_pad pad;
> +	enum v4l2_mbus_type bus_type;
> +	const struct ov2659_platform_data *pdata;
> +
> +	/* Protects the struct fields below */
> +	struct mutex lock;
> +
> +	struct i2c_client *client;
> +
> +	unsigned short id;

The id field is only used at probe time, you can make it a local variable.

> +	const struct ov2659_framesize *frame_size;
> +	/* Current Output format Register Value (REG_FORMAT_CTRL00) */
> +	struct sensor_register *format_ctrl_regs;
> +
> +	struct v4l2_mbus_framefmt format;
> +
> +	/* Sensor specific feq/pll config */
> +	struct ov2659_pll_ctrl pll;
> +
> +	int streaming;
> +	int power;
> +};

[snip]

> +static const struct ov2659_framesize ov2659_framesizes[] = {
> +	{ /* QVGA */
> +		.width		= 320,
> +		.height		= 240,
> +		.regs		= ov2659_qvga,
> +		.max_exp_lines	= 248,
> +	}, { /* VGA */
> +		.width		= 640,
> +		.height		= 480,
> +		.regs		= ov2659_vga,
> +		.max_exp_lines	= 498,
> +	}, { /* SVGA */
> +		.width		= 800,
> +		.height		= 600,
> +		.regs		= ov2659_svga,
> +		.max_exp_lines	= 498,
> +	}, { /* XGA */
> +		.width		= 1024,
> +		.height		= 768,
> +		.regs		= ov2659_xga,
> +		.max_exp_lines	= 498,
> +	}, { /* 720P */
> +		.width		= 1280,
> +		.height		= 720,
> +		.regs		= ov2659_720p,
> +		.max_exp_lines	= 498,
> +	}, { /* SXGA */
> +		.width		= 1280,
> +		.height		= 1024,
> +		.regs		= ov2659_sxga,
> +		.max_exp_lines	= 1048,
> +	}, { /* UXGA */
> +		.width		= 1600,
> +		.height		= 1200,
> +		.regs		= ov2659_uxga,
> +		.max_exp_lines	= 498,
> +	},
> +};

That's what bothers me the most about drivers for Omnivision sensors. For some 
reason (I'd bet on lack of proper documentation) they list a couple of 
supported resolutions with corresponding register values, instead of computing 
the register values from the format configured by userspace. That's not the 
way we want to go. Prabhakar, do you have enough documentation to fix that ?

[snip]

> +/* sensor register write */
> +static int ov2659_write(struct i2c_client *client, u16 reg, u8 val)
> +{
> +	struct i2c_msg msg[1];
> +	int ret, i;
> +	u8 buf[3];
> +
> +	buf[0] = reg >> 8;
> +	buf[1] = reg & 0xFF;
> +	buf[2] = val;
> +
> +	msg->addr = client->addr;
> +	msg->flags = client->flags;
> +	msg->buf = buf;
> +	msg->len = sizeof(buf);
> +
> +	for (i = 0; i < 5; i++) {

Is the loop really needed, or just copied from a different driver ?

> +		ret = i2c_transfer(client->adapter, msg, 1);
> +		if (ret >= 0)
> +			return 0;
> +
> +		dev_dbg(&client->dev,
> +			"ov2659 write reg(0x%x val:0x%x) failed !\n", reg, val);
> +		udelay(10);
> +	}
> +
> +	return ret;
> +}
> +
> +/* sensor register read */
> +static int ov2659_read(struct i2c_client *client, u16 reg, u8 *val)
> +{
> +	struct i2c_msg msg[2];
> +	int ret, i;
> +	u8 buf[2];
> +
> +	buf[0] = reg >> 8;
> +	buf[1] = reg & 0xFF;
> +
> +	msg[0].addr = client->addr;
> +	msg[0].flags = client->flags;
> +	msg[0].buf = buf;
> +	msg[0].len = sizeof(buf);
> +
> +	msg[1].addr = client->addr;
> +	msg[1].flags = client->flags|I2C_M_RD;

checkpatch.pl should have warned about this. Could you please fix checkpatch 
errors and warnings ?

> +	msg[1].buf = buf;
> +	msg[1].len = 1;
> +
> +	for (i = 0; i < 5; i++) {
> +		ret = i2c_transfer(client->adapter, msg, 2);
> +		if (ret >= 0) {
> +			*val = buf[0];
> +			return 0;
> +		}
> +
> +		dev_dbg(&client->dev,
> +			"ov2659 read reg(0x%x val:0x%x) failed !\n", reg, *val);
> +		udelay(10);
> +	}
> +
> +	return ret;
> +}
> +
> +static int ov2659_write_array(struct i2c_client *client,
> +			      const struct sensor_register *regs)
> +{
> +	int i, ret = 0;
> +
> +	for (i = 0; ret == 0 && regs[i].addr; i++) {
> +		ret = ov2659_write(client, regs[i].addr, regs[i].value);
> +		usleep_range(5000, 6000);

That will result in a large delay when the array grows. Is it really needed ? 
Waiting might be needed after writing some of the registers, but most probably 
not most of them.

> +	}
> +
> +	return ret;
> +}
> +
> +static int dump_reg(struct i2c_client *client, u16 reg)
> +{
> +	u8 val = 0;
> +	int ret;
> +
> +	ret = ov2659_read(client, reg, &val);
> +	dev_dbg(&client->dev, "%s: 0x%04x: 0x%02x\n",
> +				__func__, reg, val);
> +	return ret;
> +}
> +
> +static void ov2659_reg_dump(struct i2c_client *client)
> +{
> +	int i;
> +
> +	dump_reg(client, REG_SOFTWARE_STANDBY);
> +	dump_reg(client, REG_SOFTWARE_RESET);
> +
> +	for (i = 0x3000; i <= 0x302f; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x3400; i <= 0x3406; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x3500; i <= 0x3513; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x3600; i <= 0x3640; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x3800; i <= 0x3821; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x3a00; i <= 0x3a26; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x4000; i <= 0x4009; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x4201; i <= 0x4202; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x4300; i <= 0x4301; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x4600; i <= 0x4609; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x4700; i <= 0x4709; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x5000; i <= 0x50a0; i++)
> +		dump_reg(client, i);
> +
> +	for (i = 0x5600; i <= 0x5606; i++)
> +		dump_reg(client, i);

That's pretty rough. I'm not sure such a detailed level of debugging is 
needed. You should at least return at the beginning of the function if DEBUG 
isn't defined, to avoid reading all registers without printing their value.

> +}

[snip]

> +static void __ov2659_set_power(struct ov2659 *ov2659, int on)
> +{
> +	struct i2c_client *client = ov2659->client;
> +
> +	on = !!on;
> +
> +	dev_dbg(&client->dev, "%s: on: %d\n", __func__, on);
> +
> +	if (ov2659->power == on)
> +		return;
> +
> +	ov2659->power = on;

This seems to be a no-op. I would either remove this function, or, better, add 
regulators support to the driver.

> +}
> +
> +static int ov2659_s_power(struct v4l2_subdev *sd, int on)
> +{
> +	struct ov2659 *ov2659 = to_ov2659(sd);
> +	struct i2c_client *client = ov2659->client;
> +
> +	dev_dbg(&client->dev, "%s: on: %d\n", __func__, on);
> +
> +	mutex_lock(&ov2659->lock);
> +	__ov2659_set_power(ov2659, on);
> +	mutex_unlock(&ov2659->lock);
> +
> +	return 0;
> +}

[snip]

> +static int ov2659_s_stream(struct v4l2_subdev *sd, int on)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(sd);
> +	struct ov2659 *ov2659 = to_ov2659(sd);
> +	int ret;
> +
> +	on = !!on;
> +
> +	dev_dbg(&client->dev, "%s: on: %d\n", __func__, on);
> +
> +	if (ov2659->streaming == on)
> +		return 0;
> +
> +	mutex_lock(&ov2659->lock);

Shouldn't you protect the above check as well ?

> +
> +	if (!on) {
> +		/* Stop Streaming Sequence */
> +		ov2659_set_streaming(ov2659, 0);
> +		ov2659->streaming = on;
> +		__ov2659_set_power(ov2659, 0);
> +		mutex_unlock(&ov2659->lock);
> +
> +		return 0;
> +	}
> +
> +	/* Start Streaming Sequence */
> +	__ov2659_set_power(ov2659, 1);
> +
> +	ret = ov2659_write_array(client, ov2659_init_regs);
> +	if (ret)
> +		return ret;
> +
> +	ov2659_set_pixel_clock(ov2659);
> +	ov2659_set_frame_size(ov2659);
> +	ov2659_set_format(ov2659);
> +
> +	ov2659_set_streaming(ov2659, 1);
> +
> +	ov2659_reg_dump(client);
> +	ov2659->streaming = on;
> +	mutex_unlock(&ov2659->lock);
> +
> +	return 0;
> +}

[snip]

> +static int ov2659_detect_sensor(struct v4l2_subdev *sd)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(sd);
> +	struct ov2659 *ov2659 = to_ov2659(sd);
> +	u8 pid, ver;
> +	int ret;
> +
> +	dev_dbg(&client->dev, "%s:\n", __func__);
> +
> +	mutex_lock(&ov2659->lock);

As sensor detection is only performed from the probe function before 
registering the subdev I don't think locking is needed here.

> +	 __ov2659_set_power(ov2659, 1);
> +	usleep_range(25000, 26000);
> +
> +	/* soft reset */
> +	ret = ov2659_write(client, REG_SOFTWARE_RESET, 0x01);
> +	if (ret != 0) {
> +		dev_err(&client->dev, "Sensor soft reset failed\n");
> +		ret = -ENODEV;

ret is then ignored.

> +	}
> +	mdelay(5);

Don't delay, please sleep.

> +
> +	/* Check sensor revision */
> +	ret = ov2659_read(client, REG_SC_CHIP_ID_H, &pid);
> +	if (!ret)
> +		ret = ov2659_read(client, REG_SC_CHIP_ID_L, &ver);
> +
> +	__ov2659_set_power(ov2659, 0);
> +
> +	if (!ret) {
> +		ov2659->id = OV265X_ID(pid, ver);
> +		if (ov2659->id != OV2659_ID) {
> +			dev_err(&client->dev,
> +				"Sensor detection failed (%04X, %d)\n",
> +				ov2659->id, ret);
> +			ret = -ENODEV;
> +		} else {
> +			dev_info(&client->dev, "Found OV%04X sensor\n",
> +				ov2659->id);
> +		}
> +	}
> +	mutex_unlock(&ov2659->lock);
> +
> +	return ret;
> +}
> +
> +static struct ov2659_platform_data *
> +ov2659_get_pdata(struct i2c_client *client)
> +{
> +	struct ov2659_platform_data *pdata;
> +	struct device_node *endpoint;
> +	int ret;
> +
> +	dev_dbg(&client->dev, "ov2659_get_pdata invoked\n");
> +
> +	if (!IS_ENABLED(CONFIG_OF) || !client->dev.of_node)
> +		return client->dev.platform_data;
> +
> +	dev_dbg(&client->dev, "ov2659_get_pdata: DT Node found\n");
> +
> +	endpoint = of_graph_get_next_endpoint(client->dev.of_node, NULL);
> +	if (!endpoint)
> +		return NULL;
> +
> +	dev_dbg(&client->dev, "ov2659_get_pdata: endpoint found\n");
> +
> +	pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL);
> +	if (!pdata)
> +		goto done;
> +
> +	ret = of_property_read_u32(endpoint, "clock-frequency",
> +				   &pdata->mclk_frequency);
> +	if (ret < 0) {
> +		pdata->mclk_frequency = OV2659_DEFAULT_MCLK_FREQ;
> +		dev_info(&client->dev, "using default %u Hz clock frequency\n",
> +			 pdata->mclk_frequency);
> +	}

The clock-frequency property is defined as mandatory, a default case is thus 
not needed.

I would add CCF support to the driver and request the input clock (which is 
called xvclk and not mclk) at probe time. You could then set the clock 
frequency to the value specified in DT, and read it back to get the exact 
frequency provided by the clock source.

> +done:
> +	of_node_put(endpoint);
> +	return pdata;
> +}
> +
> +static int ov2659_probe(struct i2c_client *client,
> +			const struct i2c_device_id *id)
> +{
> +	const struct ov2659_platform_data *pdata = ov2659_get_pdata(client);
> +	struct v4l2_subdev *sd;
> +	struct ov2659 *ov2659;
> +	int ret;
> +
> +	dev_info(&client->dev, "ov2659_probe: debug: %d\n", debug);
> +
> +	if (!pdata) {
> +		dev_err(&client->dev, "platform data not specified\n");
> +		return -EINVAL;
> +	}
> +
> +	ov2659 = devm_kzalloc(&client->dev, sizeof(*ov2659), GFP_KERNEL);
> +	if (!ov2659)
> +		return -ENOMEM;
> +
> +	ov2659->pdata = pdata;
> +	mutex_init(&ov2659->lock);
> +	ov2659->client = client;
> +
> +	sd = &ov2659->sd;
> +	client->flags |= I2C_CLIENT_SCCB;
> +	v4l2_i2c_subdev_init(sd, client, &ov2659_subdev_ops);
> +	strlcpy(sd->name, DRIVER_NAME, sizeof(sd->name));
> +
> +	sd->internal_ops = &ov2659_subdev_internal_ops;
> +	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE |
> +		     V4L2_SUBDEV_FL_HAS_EVENTS;
> +
> +#if defined(CONFIG_MEDIA_CONTROLLER)
> +	ov2659->pad.flags = MEDIA_PAD_FL_SOURCE;
> +	sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR;
> +	ret = media_entity_init(&sd->entity, 1, &ov2659->pad, 0);
> +	if (ret < 0)
> +		return ret;
> +#endif
> +
> +	ov2659_get_default_format(&ov2659->format);
> +	ov2659->frame_size = &ov2659_framesizes[2];
> +	ov2659->format_ctrl_regs = ov2659_formats[0].format_ctrl_regs;
> +
> +	ret = ov2659_detect_sensor(sd);
> +	if (ret < 0)
> +		goto error;
> +
> +	/* Calculate the PLL register value needed */
> +	ov2659_pll_calc_params(ov2659);
> +
> +	ret = v4l2_async_register_subdev(&ov2659->sd);
> +	if (ret)
> +		goto error;
> +
> +	dev_info(&client->dev, "%s sensor driver registered !!\n", sd->name);
> +
> +	return 0;
> +
> +error:
> +#if defined(CONFIG_MEDIA_CONTROLLER)
> +	media_entity_cleanup(&sd->entity);
> +#endif
> +	return ret;
> +}
> +
> +static int ov2659_remove(struct i2c_client *client)
> +{
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +
> +	v4l2_device_unregister_subdev(sd);
> +#if defined(CONFIG_MEDIA_CONTROLLER)
> +	media_entity_cleanup(&sd->entity);
> +#endif
> +	return 0;
> +}
> +
> +static const struct i2c_device_id ov2659_id[] = {
> +	{ "ov2659", 0 },
> +	{ /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(i2c, ov2659_id);
> +
> +#if IS_ENABLED(CONFIG_OF)
> +static const struct of_device_id ov2659_of_match[] = {
> +	{ .compatible = "ovt,ov2659", },
> +	{ /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, ov2659_of_match);
> +#endif
> +
> +static struct i2c_driver ov2659_i2c_driver = {
> +	.driver = {
> +		.owner = THIS_MODULE,
> +		.name	= DRIVER_NAME,
> +		.of_match_table = of_match_ptr(ov2659_of_match),
> +	},
> +	.probe		= ov2659_probe,
> +	.remove		= ov2659_remove,
> +	.id_table	= ov2659_id,
> +};
> +
> +module_i2c_driver(ov2659_i2c_driver);
> +
> +MODULE_AUTHOR("Benoit Parrot <bparrot@xxxxxx>");
> +MODULE_DESCRIPTION("OV2659 CMOS Image Sensor driver");
> +MODULE_LICENSE("GPL");

-- 
Regards,

Laurent Pinchart

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux