From: Yang Xiwen <forbidden405@xxxxxxxxxxx> Convert the old text binding to new YAML. While at it, make some changes to the binding: - The version numbers are not documented publicly. The version also does not change programming interface. Remove it until it's really needed. - A few clocks are missing in old binding file. Add them to match the real hardware. Signed-off-by: Yang Xiwen <forbidden405@xxxxxxxxxxx> --- .../bindings/net/hisilicon,hisi-femac.yaml | 87 ++++++++++++++++++++++ .../devicetree/bindings/net/hisilicon-femac.txt | 41 ---------- 2 files changed, 87 insertions(+), 41 deletions(-) diff --git a/Documentation/devicetree/bindings/net/hisilicon,hisi-femac.yaml b/Documentation/devicetree/bindings/net/hisilicon,hisi-femac.yaml new file mode 100644 index 000000000000..3344d3bfefb8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon,hisi-femac.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/hisilicon,hisi-femac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hisilicon Fast Ethernet MAC controller + +maintainers: + - Yang Xiwen <forbidden405@xxxxxxxxxxx> + +allOf: + - $ref: ethernet-controller.yaml + +properties: + compatible: + enum: + - hisilicon,hi3516cv300-femac + + reg: + items: + - description: The first region is the MAC core register base and size. + - description: The second region is the global MAC control register. + + interrupts: + maxItems: 1 + + clocks: + items: + - description: MAC main clock + - description: MAC bus interface clock + - description: PHY clock + + clock-names: + items: + - const: mac + - const: macif + - const: phy + + resets: + items: + - description: MAC reset signal + - description: PHY reset signal + + reset-names: + items: + - const: mac + - const: phy + + hisilicon,phy-reset-delays-us: + description: PHY reset timing requirement (in micro seconds). + The integrated PHY usually have a special reset timing sequence and must + interact with MAC controller to accomplish the entire reset procedure. So + these properties belong to MAC controller, not PHY. + items: + - description: pre-reset delay for PHY + - description: reset pulse for PHY + - description: post-reset delay for PHY + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - reset-names + - phy-mode + - phy-handle + - hisilicon,phy-reset-delays-us + +unevaluatedProperties: false + +examples: + - | + ethernet@10090000 { + compatible = "hisilicon,hi3516cv300-femac"; + reg = <0x10090000 0x1000>, <0x10091300 0x200>; + interrupts = <12>; + clocks = <&clk_femac>, <&clk_femacif>, <&clk_fephy>; + clock-names = "mac", "macif", "phy"; + resets = <&crg 0xec 0>, <&crg 0xec 3>; + reset-names = "mac", "phy"; + mac-address = [00 00 00 00 00 00]; + phy-mode = "mii"; + phy-handle = <&fephy>; + hisilicon,phy-reset-delays-us = <10000 20000 20000>; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac.txt b/Documentation/devicetree/bindings/net/hisilicon-femac.txt deleted file mode 100644 index 5f96976f3cea..000000000000 --- a/Documentation/devicetree/bindings/net/hisilicon-femac.txt +++ /dev/null @@ -1,41 +0,0 @@ -Hisilicon Fast Ethernet MAC controller - -Required properties: -- compatible: should contain one of the following version strings: - * "hisilicon,hisi-femac-v1" - * "hisilicon,hisi-femac-v2" - and the soc string "hisilicon,hi3516cv300-femac". -- reg: specifies base physical address(s) and size of the device registers. - The first region is the MAC core register base and size. - The second region is the global MAC control register. -- interrupts: should contain the MAC interrupt. -- clocks: A phandle to the MAC main clock. -- resets: should contain the phandle to the MAC reset signal(required) and - the PHY reset signal(optional). -- reset-names: should contain the reset signal name "mac"(required) - and "phy"(optional). -- phy-mode: see ethernet.txt [1]. -- phy-handle: see ethernet.txt [1]. -- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. - The 1st cell is reset pre-delay in micro seconds. - The 2nd cell is reset pulse in micro seconds. - The 3rd cell is reset post-delay in micro seconds. - -The MAC address will be determined using the optional properties -defined in ethernet.txt[1]. - -[1] Documentation/devicetree/bindings/net/ethernet.txt - -Example: - hisi_femac: ethernet@10090000 { - compatible = "hisilicon,hi3516cv300-femac","hisilicon,hisi-femac-v2"; - reg = <0x10090000 0x1000>,<0x10091300 0x200>; - interrupts = <12>; - clocks = <&crg HI3518EV200_ETH_CLK>; - resets = <&crg 0xec 0>,<&crg 0xec 3>; - reset-names = "mac","phy"; - mac-address = [00 00 00 00 00 00]; - phy-mode = "mii"; - phy-handle = <&phy0>; - hisilicon,phy-reset-delays-us = <10000 20000 20000>; - }; -- 2.43.0
