Hi Roger,
On 02/03/24 02:59, Roger Quadros wrote:
>
>
> On 01/03/2024 22:58, Roger Quadros wrote:
>>
>>
>> On 29/02/2024 18:25, Roger Quadros wrote:
>>> The RESET GPIO pinmux should be part of MDIO bus node
>>> so that they can be in the right state before the PHY
>>> can be probed via MDIO bus scan.
>>>
>>> Add GPIO reset for the Gigabit Ethernet PHY. As per
>>> RTL8211F datasheet, reset assert width is 10ms and
>>> PHY registers can be access accessed after 50ms of
>>> reset deassert.
>>>
>>> Signed-off-by: Roger Quadros <rogerq@xxxxxxxxxx>
>>> ---
>>> arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts | 8 ++++++--
>>> 1 file changed, 6 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
>>> index a34e0df2ab86..77240cf3ae4d 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
>>> +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
>>> @@ -292,6 +292,8 @@ mdio0_pins_default: mdio0-default-pins {
>>> pinctrl-single,pins = <
>>> AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
>>> AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
>>> + AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25) GPMC0_AD0.GPIO0_15 */
>>
>> This should be PIN_OUTPUT.
>> Will fix in next spin.
>
> Actually PIN_INPUT is correct else we won't be able to read the correct GPIO pin status
> on gpio read.
> I observe this issue on u-boot at least.
>
>>
>>> + AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
>
> This one needs to be fixed to PIN_INPUT.
While at it, please fix the $subject prefix:
arm64: dts: ti: beagleplay: ...
Do we need a Fixes: Tag too?
>
>>> >;
>>> };
>>>
>>> @@ -383,7 +385,6 @@ AM62X_IOPAD(0x017c, PIN_INPUT, 1) /* (AD22) RGMII2_RX_CTL.RMII2_RX_ER */
>>> AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
>>> AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
>>> AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
>>> - AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
>>> AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
>>> AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
>>> >;
>>> @@ -597,6 +598,9 @@ &cpsw3g_mdio {
>>>
>>> cpsw3g_phy0: ethernet-phy@0 {
>>> reg = <0>;
>>> + reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
>>> + reset-assert-us = <10000>;
>>> + reset-deassert-us = <50000>;
>>> };
>>>
>>> cpsw3g_phy1: ethernet-phy@1 {
>>> @@ -615,7 +619,7 @@ &main_gpio0 {
>>> "USR0", "USR1", "USR2", "USR3", "", "", "USR4", /* 3-9 */
>>> "EEPROM_WP", /* 10 */
>>> "CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2", /* 11-12 */
>>> - "CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "", /* 13-17 */
>>> + "CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "", /* 13-17 */
>>> "USR_BUTTON", "", "", "", "", "", "", "", "", /* 18-26 */
>>> "", "", "", "", "", "", "", "", "", "HDMI_INT", /* 27-36 */
>>> "", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
>>>
>>> ---
>>> base-commit: bbef42084cc170cbfc035bf784f2ff055c939d7e
>>> change-id: 20240229-b4-for-v6-9-am65-beagleplay-ethernet-reset-098f274fbf15
>>>
>>> Best regards,
>>
>
--
Regards
Vignesh
