On 2024-02-26 05:13, Uwe Kleine-König wrote:
On Wed, Jan 31, 2024 at 04:40:41PM -0500, Trevor Gamblin wrote:
From: Drew Fustini <dfustini@xxxxxxxxxxxx>
Add support for the Analog Devices AXI PWM Generator. This device is an
FPGA-implemented peripheral used as PWM signal generator and can be
interfaced with AXI4. The register map of this peripheral makes it
possible to configure the period and duty cycle of the output signal.
Link: https://wiki.analog.com/resources/fpga/docs/axi_pwm_gen
Co-developed-by: Sergiu Cuciurean <sergiu.cuciurean@xxxxxxxxxx>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@xxxxxxxxxx>
Co-developed-by: David Lechner <dlechner@xxxxxxxxxxxx>
Signed-off-by: David Lechner <dlechner@xxxxxxxxxxxx>
Signed-off-by: Drew Fustini <dfustini@xxxxxxxxxxxx>
Co-developed-by: Trevor Gamblin <tgamblin@xxxxxxxxxxxx>
Acked-by: Nuno Sa <nuno.sa@xxxxxxxxxx>
Signed-off-by: Trevor Gamblin <tgamblin@xxxxxxxxxxxx>
---
v3 changes:
* Address feedback for driver in v2:
* Remove unnecessary blank line in axi_pwmgen_apply
* Use macros already defined in <linux/fpga/adi-axi-common.h> for
version checking
v2 changes:
* Address feedback for driver and device tree in v1:
* Use more reasonable Kconfig approach
* Use common prefixes for all functions
* Rename axi_pwmgen struct to axi_pwmgen_ddata
* Change use of "pwm" to "ddata"
* Set and check state->polarity
* Multiply safely with mul_u64_u64_div_u64()
* Improve handling of max and zero periods
* Error if clk_rate_hz > NSEC_PER_SEC
* Add "Limitations" section at top of pwm-axi-pwmgen.c
* Don't disable outputs by default
* Remove unnecessary macros for period, duty, offset
* Fix axi_pwmgen_ddata alignment
* Don't artificially limit npwm to four
* Use clk_rate_exclusive_get(), balance with clk_rate_exclusive_put()
* Cache clk rate in axi_pwmgen_ddata
* Don't assign pwm->chip.base, do assign pwm->chip.atomic
* Remove redundant calls to clk_get_rate
* Test contents of AXI_PWMGEN_REG_CORE_MAGIC instead of
arbitrary AXI_PWMGEN_TEST_DATA in AXI_PWMGEN_REG_SCRATCHPAD
* Remove redundant clk struct from axi_pwmgen_ddata
* Add self as module author
* Add major version check for IP core
---
MAINTAINERS | 1 +
drivers/pwm/Kconfig | 13 ++
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-axi-pwmgen.c | 242 +++++++++++++++++++++++++++++++++++
4 files changed, 257 insertions(+)
create mode 100644 drivers/pwm/pwm-axi-pwmgen.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 8a4ed5545680..2baa7a0a1c8c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3438,6 +3438,7 @@ L: linux-pwm@xxxxxxxxxxxxxxx
S: Supported
W: https://ez.analog.com/linux-software-drivers
F: Documentation/devicetree/bindings/pwm/adi,axi-pwmgen.yaml
+F: drivers/pwm/pwm-axi-pwmgen.c
AXXIA I2C CONTROLLER
M: Krzysztof Adamski <krzysztof.adamski@xxxxxxxxx>
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 4b956d661755..d44b0e86adee 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -98,6 +98,19 @@ config PWM_ATMEL_TCB
To compile this driver as a module, choose M here: the module
will be called pwm-atmel-tcb.
+config PWM_AXI_PWMGEN
+ tristate "Analog Devices AXI PWM generator"
+ depends on MICROBLAZE || NIOS2 || ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_INTEL_SOCFPGA || COMPILE_TEST
+ select REGMAP_MMIO
+ help
+ This enables support for the Analog Devices AXI PWM generator.
+
+ This is a configurable PWM generator with variable pulse width and
+ period.
+
+ To compile this driver as a module, choose M here: the module will be
+ called pwm-axi-pwmgen.
+
config PWM_BCM_IPROC
tristate "iProc PWM support"
depends on ARCH_BCM_IPROC || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index c5ec9e168ee7..8322089954e9 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_PWM_APPLE) += pwm-apple.o
obj-$(CONFIG_PWM_ATMEL) += pwm-atmel.o
obj-$(CONFIG_PWM_ATMEL_HLCDC_PWM) += pwm-atmel-hlcdc.o
obj-$(CONFIG_PWM_ATMEL_TCB) += pwm-atmel-tcb.o
+obj-$(CONFIG_PWM_AXI_PWMGEN) += pwm-axi-pwmgen.o
obj-$(CONFIG_PWM_BCM_IPROC) += pwm-bcm-iproc.o
obj-$(CONFIG_PWM_BCM_KONA) += pwm-bcm-kona.o
obj-$(CONFIG_PWM_BCM2835) += pwm-bcm2835.o
diff --git a/drivers/pwm/pwm-axi-pwmgen.c b/drivers/pwm/pwm-axi-pwmgen.c
new file mode 100644
index 000000000000..44e62e90b227
--- /dev/null
+++ b/drivers/pwm/pwm-axi-pwmgen.c
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Analog Devices AXI PWM generator
+ *
+ * Copyright 2024 Analog Devices Inc.
+ * Copyright 2024 Baylibre SAS
+ *
+ * Limitations:
+ * - The writes to registers for period and duty are shadowed until
+ * LOAD_CONFIG is written to AXI_PWMGEN_REG_CONFIG at the end of the
+ * current period.
+ * - Writing LOAD_CONFIG also has the effect of re-synchronizing all
+ * enabled channels, which could cause glitching on other channels. It
+ * is therefore expected that channels are assigned harmonic periods
+ * and all have a single user coordinating this.
That means that when I reconfigure pwm2 the currently running period of
pwm2 is completed and then all pwmX's counters are reset to zero?
Right.
The patch looks good to me now. It needs a rework to use
pwmchip_alloc(). If you could care for that, that would be great.
Otherwise I'd pick up your patch later and add the conversion myself.
Will do. Working on the change now. Once I've done some testing I'll
submit the v4.
Best regards
Uwe
