Re: [PATCH v6 3/5] mmc: dw_mmc: add support for hi3798mv200

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 21 Feb 2024 at 13:45, Yang Xiwen via B4 Relay
<devnull+forbidden405.outlook.com@xxxxxxxxxx> wrote:
>
> From: Yang Xiwen <forbidden405@xxxxxxxxxxx>
>
> Add support for Hi3798MV200 specific extension.
>
> Signed-off-by: Yang Xiwen <forbidden405@xxxxxxxxxxx>
> ---
>  drivers/mmc/host/Kconfig              |   9 ++
>  drivers/mmc/host/Makefile             |   1 +
>  drivers/mmc/host/dw_mmc-hi3798mv200.c | 239 ++++++++++++++++++++++++++++++++++
>  3 files changed, 249 insertions(+)
>
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 81f2c4e05287..aebc587f77a7 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -798,6 +798,15 @@ config MMC_DW_HI3798CV200
>           Synopsys DesignWare Memory Card Interface driver. Select this option
>           for platforms based on HiSilicon Hi3798CV200 SoC.
>
> +config MMC_DW_HI3798MV200
> +       tristate "Hi3798MV200 specific extensions for Synopsys DW Memory Card Interface"
> +       depends on MMC_DW
> +       select MMC_DW_PLTFM
> +       help
> +         This selects support for HiSilicon Hi3798MV200 SoC specific extensions to the
> +         Synopsys DesignWare Memory Card Interface driver. Select this option
> +         for platforms based on HiSilicon Hi3798MV200 SoC.
> +
>  config MMC_DW_K3
>         tristate "K3 specific extensions for Synopsys DW Memory Card Interface"
>         depends on MMC_DW
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index d0be4465f3ec..f53f86d200ac 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -51,6 +51,7 @@ obj-$(CONFIG_MMC_DW_PLTFM)    += dw_mmc-pltfm.o
>  obj-$(CONFIG_MMC_DW_BLUEFIELD) += dw_mmc-bluefield.o
>  obj-$(CONFIG_MMC_DW_EXYNOS)    += dw_mmc-exynos.o
>  obj-$(CONFIG_MMC_DW_HI3798CV200) += dw_mmc-hi3798cv200.o
> +obj-$(CONFIG_MMC_DW_HI3798MV200) += dw_mmc-hi3798mv200.o
>  obj-$(CONFIG_MMC_DW_K3)                += dw_mmc-k3.o
>  obj-$(CONFIG_MMC_DW_PCI)       += dw_mmc-pci.o
>  obj-$(CONFIG_MMC_DW_ROCKCHIP)  += dw_mmc-rockchip.o
> diff --git a/drivers/mmc/host/dw_mmc-hi3798mv200.c b/drivers/mmc/host/dw_mmc-hi3798mv200.c
> new file mode 100644
> index 000000000000..73aaa21040ea
> --- /dev/null
> +++ b/drivers/mmc/host/dw_mmc-hi3798mv200.c
> @@ -0,0 +1,239 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Modified from dw_mmc-hi3798cv200.c
> + *
> + * Copyright (c) 2024 Yang Xiwen <forbidden405@xxxxxxxxxxx>
> + * Copyright (c) 2018 HiSilicon Technologies Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/mmc/host.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include "dw_mmc.h"
> +#include "dw_mmc-pltfm.h"
> +
> +#define SDMMC_TUNING_CTRL      0x118
> +#define SDMMC_TUNING_FIND_EDGE BIT(5)
> +
> +#define ALL_INT_CLR            0x1ffff
> +
> +/* DLL ctrl reg */
> +#define SAP_DLL_CTRL_DLLMODE   BIT(16)
> +
> +struct dw_mci_hi3798mv200_priv {
> +       struct clk *sample_clk;
> +       struct clk *drive_clk;
> +       struct regmap *crg_reg;
> +       u32 sap_dll_offset;
> +       struct mmc_clk_phase_map phase_map;
> +};
> +
> +static void dw_mci_hi3798mv200_set_ios(struct dw_mci *host, struct mmc_ios *ios)
> +{
> +       struct dw_mci_hi3798mv200_priv *priv = host->priv;
> +       struct mmc_clk_phase phase = priv->phase_map.phase[ios->timing];
> +       u32 val;
> +
> +       val = mci_readl(host, ENABLE_SHIFT);
> +       if (ios->timing == MMC_TIMING_MMC_DDR52
> +           || ios->timing == MMC_TIMING_UHS_DDR50)
> +               val |= SDMMC_ENABLE_PHASE;
> +       else
> +               val &= ~SDMMC_ENABLE_PHASE;
> +       mci_writel(host, ENABLE_SHIFT, val);
> +
> +       val = mci_readl(host, DDR_REG);
> +       if (ios->timing == MMC_TIMING_MMC_HS400)
> +               val |= SDMMC_DDR_HS400;
> +       else
> +               val &= ~SDMMC_DDR_HS400;
> +       mci_writel(host, DDR_REG, val);
> +
> +       if (clk_set_rate(host->ciu_clk, ios->clock))
> +               dev_warn(host->dev, "Failed to set rate to %u\n", ios->clock);
> +       else
> +               // CLK_MUX_ROUND_NEAREST is enabled for this clock
> +               // The actual clock rate is not what we setted, but a rounded value
> +               // so we should get the rate once again

Please use proper comments sections (/* .... */) and not "//".

> +               host->bus_hz = clk_get_rate(host->ciu_clk);
> +
> +       if (phase.valid) {
> +               clk_set_phase(priv->drive_clk, phase.out_deg);
> +               clk_set_phase(priv->sample_clk, phase.in_deg);
> +       } else {
> +               dev_warn(host->dev,
> +                        "The phase entry for timing mode %d is missing in device tree.\n",
> +                        ios->timing);
> +       }
> +}
> +
> +static inline int dw_mci_hi3798mv200_enable_tuning(struct dw_mci_slot *slot)
> +{
> +       struct dw_mci_hi3798mv200_priv *priv = slot->host->priv;
> +
> +       return regmap_clear_bits(priv->crg_reg, priv->sap_dll_offset, SAP_DLL_CTRL_DLLMODE);
> +}
> +
> +static inline int dw_mci_hi3798mv200_disable_tuning(struct dw_mci_slot *slot)
> +{
> +       struct dw_mci_hi3798mv200_priv *priv = slot->host->priv;
> +
> +       return regmap_set_bits(priv->crg_reg, priv->sap_dll_offset, SAP_DLL_CTRL_DLLMODE);
> +}
> +
> +static int dw_mci_hi3798mv200_execute_tuning_mix_mode(struct dw_mci_slot *slot,
> +                                            u32 opcode)
> +{
> +       static const int degrees[] = { 0, 45, 90, 135, 180, 225, 270, 315 };
> +       struct dw_mci *host = slot->host;
> +       struct dw_mci_hi3798mv200_priv *priv = host->priv;
> +       int raise_point = -1, fall_point = -1;
> +       int err, prev_err = -1;
> +       int found = 0;
> +       int regval;
> +       int i;
> +       int ret;
> +
> +       // enable tuning

Looks like a redundant comment, please drop it.

> +       ret = dw_mci_hi3798mv200_enable_tuning(slot);
> +       if (ret < 0)
> +               return ret;

A newline here would improve the readability I think.

> +       for (i = 0; i < ARRAY_SIZE(degrees); i++) {
> +               clk_set_phase(priv->sample_clk, degrees[i]);
> +               mci_writel(host, RINTSTS, ALL_INT_CLR);
> +
> +               err = mmc_send_tuning(slot->mmc, opcode, NULL);
> +               if (!err) {
> +                       regval = mci_readl(host, TUNING_CTRL);
> +                       if (regval & SDMMC_TUNING_FIND_EDGE)
> +                               err = 1;
> +                       else
> +                               found = 1;
> +               };
> +
> +               if (i > 0) {
> +                       if (err && !prev_err)
> +                               fall_point = i - 1;
> +                       if (!err && prev_err)
> +                               raise_point = i;
> +               }
> +
> +               if (raise_point != -1 && fall_point != -1)
> +                       goto tuning_out;
> +
> +               prev_err = err;
> +               err = 0;
> +       }
> +
> +tuning_out:
> +       ret = dw_mci_hi3798mv200_disable_tuning(slot);
> +       if (ret < 0)
> +               return ret;
> +       if (found) {
> +               if (raise_point == -1)
> +                       raise_point = 0;
> +               if (fall_point == -1)
> +                       fall_point = ARRAY_SIZE(degrees) - 1;
> +               if (fall_point < raise_point) {
> +                       if ((raise_point + fall_point) >
> +                           (ARRAY_SIZE(degrees) - 1))
> +                               i = fall_point / 2;
> +                       else
> +                               i = (raise_point + ARRAY_SIZE(degrees) - 1) / 2;
> +               } else {
> +                       i = (raise_point + fall_point) / 2;
> +               }
> +
> +               // use the same phase table for both HS200 and HS400

Don't use "//" for comments.

> +               priv->phase_map.phase[MMC_TIMING_MMC_HS200].in_deg = degrees[i];
> +               priv->phase_map.phase[MMC_TIMING_MMC_HS400].in_deg = degrees[i];
> +
> +               clk_set_phase(priv->sample_clk, degrees[i]);
> +               dev_dbg(host->dev, "Tuning clk_sample[%d, %d], set[%d]\n",
> +                       raise_point, fall_point, degrees[i]);
> +               err = 0;
> +       } else {
> +               dev_err(host->dev, "No valid clk_sample shift! use default\n");
> +               err = -EINVAL;
> +       }
> +
> +       mci_writel(host, RINTSTS, ALL_INT_CLR);
> +       return err;

The entire code in dw_mci_hi3798mv200_execute_tuning_mix_mode() looks
rather messy to me. A lot of variables are being used, set and reset
from everywhere.

Would you mind having a closer look and try to improve it a bit, so it
becomes easier to follow what is going on?

> +}
> +
> +static int dw_mci_hi3798mv200_init(struct dw_mci *host)
> +{
> +       struct dw_mci_hi3798mv200_priv *priv;
> +       struct device_node *np = host->dev->of_node;
> +       int ret;
> +
> +       priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
> +       if (!priv)
> +               return -ENOMEM;
> +
> +       mmc_of_parse_clk_phase(host->dev, &priv->phase_map);
> +
> +       priv->sample_clk = devm_clk_get_enabled(host->dev, "ciu-sample");
> +       if (IS_ERR(priv->sample_clk))
> +               return dev_err_probe(host->dev, PTR_ERR(priv->sample_clk),
> +                                    "failed to get enabled ciu-sample clock\n");
> +
> +       priv->drive_clk = devm_clk_get_enabled(host->dev, "ciu-drive");
> +       if (IS_ERR(priv->drive_clk))
> +               return dev_err_probe(host->dev, PTR_ERR(priv->drive_clk),
> +                                    "failed to get enabled ciu-drive clock\n");
> +
> +       priv->crg_reg = syscon_regmap_lookup_by_phandle(np, "hisilicon,sap-dll-reg");
> +       if (IS_ERR(priv->crg_reg))
> +               return dev_err_probe(host->dev, PTR_ERR(priv->crg_reg),
> +                                    "failed to get CRG reg\n");
> +
> +       ret = of_property_read_u32_index(np, "hisilicon,sap-dll-reg", 1, &priv->sap_dll_offset);
> +       if (ret)
> +               return dev_err_probe(host->dev, ret, "failed to get sample DLL register offset\n");
> +
> +       host->priv = priv;
> +       return 0;
> +}
> +
> +static const struct dw_mci_drv_data hi3798mv200_data = {
> +       .common_caps = MMC_CAP_CMD23,
> +       .init = dw_mci_hi3798mv200_init,
> +       .set_ios = dw_mci_hi3798mv200_set_ios,
> +       .execute_tuning = dw_mci_hi3798mv200_execute_tuning_mix_mode,
> +};
> +
> +static const struct of_device_id dw_mci_hi3798mv200_match[] = {
> +       { .compatible = "hisilicon,hi3798mv200-dw-mshc" },
> +       {},
> +};
> +
> +static int dw_mci_hi3798mv200_probe(struct platform_device *pdev)
> +{
> +       return dw_mci_pltfm_register(pdev, &hi3798mv200_data);
> +}
> +
> +static void dw_mci_hi3798mv200_remove(struct platform_device *pdev)
> +{
> +       dw_mci_pltfm_remove(pdev);
> +}
> +
> +MODULE_DEVICE_TABLE(of, dw_mci_hi3798mv200_match);
> +static struct platform_driver dw_mci_hi3798mv200_driver = {
> +       .probe = dw_mci_hi3798mv200_probe,
> +       .remove_new = dw_mci_hi3798mv200_remove,
> +       .driver = {
> +               .name = "dwmmc_hi3798mv200",
> +               .probe_type = PROBE_PREFER_ASYNCHRONOUS,
> +               .of_match_table = dw_mci_hi3798mv200_match,
> +       },
> +};
> +module_platform_driver(dw_mci_hi3798mv200_driver);
> +
> +MODULE_DESCRIPTION("HiSilicon Hi3798MV200 Specific DW-MSHC Driver Extension");
> +MODULE_LICENSE("GPL");
>

Kind regards
Uffe




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux