On Thu, 2024-02-22 at 11:25 +0800, Kelly Hung wrote:
> Base on aspeed-g6.dtsi and can boot into BMC console.
>
> Signed-off-by: Kelly Hung <Kelly_Hung@xxxxxxxx>
> ---
> arch/arm/boot/dts/aspeed/Makefile | 3 +-
> .../boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts | 651 ++++++++++++++++++
> 2 files changed, 653 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
>
> diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
> index d3ac20e316d0..f7cc69b636fc 100644
> --- a/arch/arm/boot/dts/aspeed/Makefile
> +++ b/arch/arm/boot/dts/aspeed/Makefile
> @@ -62,4 +62,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-ufispace-ncplite.dtb \
> aspeed-bmc-vegman-n110.dtb \
> aspeed-bmc-vegman-rx20.dtb \
> - aspeed-bmc-vegman-sx20.dtb
> + aspeed-bmc-vegman-sx20.dtb \
> + aspeed-bmc-asus-x4tf.dtb
Please keep the list sorted alphabetically.
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
> new file mode 100644
> index 000000000000..fbe39eaec154
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
> @@ -0,0 +1,651 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 ASUS Corp.
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include "aspeed-g6-pinctrl.dtsi"
> +#include <dt-bindings/i2c/i2c.h>
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "ASUS-X4TF";
> + compatible = "asus,x4tf", "aspeed,ast2600";
> +
> + aliases {
> + serial4 = &uart5;
> + };
> +
> + chosen {
> + stdout-path = "serial4:115200n8";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x40000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + video_engine_memory: video {
> + size = <0x04000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
> + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
> + <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
> + <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-heartbeat {
> + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led-uid {
> + gpios = <&gpio0 ASPEED_GPIO(P, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
> + default-state = "off";
> + };
> +
> + led-status_Y {
> + gpios = <&gpio1 ASPEED_GPIO(B, 1) GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + };
> +
> + led-sys_boot_status {
> + gpios = <&gpio1 ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + };
> + };
> +};
> +
> +&adc0 {
> + vref = <2500>;
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
> + &pinctrl_adc2_default &pinctrl_adc3_default
> + &pinctrl_adc4_default &pinctrl_adc5_default
> + &pinctrl_adc6_default &pinctrl_adc7_default>;
> +};
> +
> +&adc1 {
> + vref = <2500>;
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
> + &pinctrl_adc10_default &pinctrl_adc11_default
> + &pinctrl_adc12_default &pinctrl_adc13_default
> + &pinctrl_adc14_default &pinctrl_adc15_default>;
> +};
> +
> +&peci0 {
> + status = "okay";
> +};
> +
> +&lpc_snoop {
> + snoop-ports = <0x80>;
> + status = "okay";
> +};
> +
> +&mdio2 {
> + status = "okay";
> +
> + ethphy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio3 {
> + status = "okay";
> +
> + ethphy3: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
Are these necessary given you have `use-ncsi` specified for the MACs
below?
> +
> +&mac2 {
> + status = "okay";
> + phy-mode = "rmii";
> + use-ncsi;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii3_default>;
> +};
> +
> +&mac3 {
> + status = "okay";
> + phy-mode = "rmii";
> + use-ncsi;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii4_default>;
> +};
> +
> +&fmc {
> + status = "okay";
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc-spi";
> + spi-max-frequency = <50000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + bmc@0 {
> + label = "bmc";
> + reg = <0x0 0x4000000>;
> + };
> +
> + u-boot@0 {
> + label = "u-boot";
> + reg = <0x0 0x200000>;
> + };
> +
> + u-boot-env@1f0000 {
> + label = "u-boot-env";
> + reg = <0x1f0000 0x10000>;
> + };
> +
> + kernel@200000 {
> + label = "kernel";
> + reg = <0x200000 0xc00000>;
> + };
> +
> + rofs@a00000 {
> + label = "rofs";
> + reg = <0xa00000 0x2a00000>;
> + };
> +
> + rwfs@2a00000 {
> + label = "rwfs";
> + reg = <0x2a00000 0x43f0000>;
> + };
Is this different to the default OpenBMC layouts? Can you use the
appropriate DTSI?
> + };
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash@0 {
> + status = "okay";
> + label = "bios-spi";
> + spi-max-frequency = <50000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + biosfullimg@0 {
> + reg = <0x0 0x2000000>; //32768 *1024 = 32 MB
> + label = "biosfullimg";
> + };
> + };
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +
> + temperature-sensor@48 {
> + compatible = "ti,tmp75";
> + reg = <0x48>;
> + };
> +
> + temperature-sensor@49 {
> + compatible = "ti,tmp75";
> + reg = <0x49>;
> + };
> +
> + pca9555_4_20: gpio@20 {
> + compatible = "nxp,pca9555";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + pca9555_4_22: gpio@22 {
> + compatible = "nxp,pca9555";
> + reg = <0x22>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + pca9555_4_24: gpio@24 {
> + compatible = "nxp,pca9555";
> + reg = <0x24>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + /*A0 - A3 0*/ "", "STRAP_BMC_BATTERY_GPIO1", "", "",
> + /*A4 - A7 4*/ "", "", "", "",
> + /*B0 - B7 8*/ "", "", "", "", "", "", "", "";
> + };
> +
> + pca9555_4_26: gpio@26 {
> + compatible = "nxp,pca9555";
> + reg = <0x26>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + i2c-mux@70 {
> + compatible = "nxp,pca9546";
> + status = "okay";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel_1: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + channel_2: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + channel_3: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + channel_4: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +
> + pca9555_5_24: gpio@24 {
> + compatible = "nxp,pca9555";
> + reg = <0x24>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + i2c-mux@70 {
> + compatible = "nxp,pca9546";
> + status = "okay";
> + reg = <0x70 >;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel_5: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + pca9555_5_5_20: gpio@20 {
> + compatible = "nxp,pca9555";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + "", "", "", "", "", "", "", "",
> + "", "", "SYS_FAN6", "SYS_FAN5",
> + "SYS_FAN4", "SYS_FAN3",
> + "SYS_FAN2", "SYS_FAN1";
> + };
> +
> + pca9555_5_5_21: gpio@21 {
> + compatible = "nxp,pca9555";
> + reg = <0x21>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + power-monitor@44 {
> + compatible = "ti,ina219";
> + reg = <0x44>;
> + shunt-resistor = <2>;
> + };
> + };
> +
> + channel_6: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + channel_7: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + channel_8: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c6 {
> + status = "okay";
> +
> + pca9555_6_27: gpio@27 {
> + compatible = "nxp,pca9555";
> + reg = <0x27>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + pca9555_6_20: gpio@20 {
> + compatible = "nxp,pca9555";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + /*A0 0*/ "", "", "", "", "", "", "", "",
> + /*B0 8*/ "Drive_NVMe1", "Drive_NVMe2", "", "",
> + /*B4 12*/ "", "", "", "";
> + };
> +
> + pca9555_6_21: gpio@21 {
> + compatible = "nxp,pca9555";
> + reg = <0x21>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + i2c-mux@70 {
> + compatible = "nxp,pca9546";
> + status = "okay";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + idle-state = <1>;
> +
> + channel_9: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + temperature-sensor@48 {
> + compatible = "ti,tmp75";
> + reg = <0x48>;
> + };
> +
> + temperature-sensor@49 {
> + compatible = "ti,tmp75";
> + reg = <0x49>;
> + };
> +
> + power-monitor@40 {
> + compatible = "ti,ina219";
> + reg = <0x40>;
> + shunt-resistor = <2>;
> + };
> +
> + power-monitor@41 {
> + compatible = "ti,ina219";
> + reg = <0x41>;
> + shunt-resistor = <5>;
> + };
> + };
> +
> + channel_10: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + channel_11: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + channel_12: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +
> + i2c-mux@71 {
> + compatible = "nxp,pca9546";
> + status = "okay";
> + reg = <0x71>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect;
> +
> + channel_13: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + channel_14: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + channel_15: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + channel_16: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c8 {
> + status = "okay";
> +
> + i2c-mux@70 {
> + compatible = "nxp,pca9546";
> + status = "okay";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect;
> +
> + channel_17: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + channel_18: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + temperature-sensor@48 {
> + compatible = "ti,tmp75";
> + reg = <0x48>;
> + };
> +
> + power-monitor@41 {
> + compatible = "ti,ina219";
> + reg = <0x41>;
> + shunt-resistor = <5>;
> + };
> + };
> +
> + channel_19: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + channel_20: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c9 {
> + status = "okay";
> +};
> +
> +&i2c10 {
> + status = "okay";
> +};
> +
> +&i2c11 {
> + status = "okay";
> +};
> +
> +&i2c14 {
> + status = "okay";
> + multi-master;
> +
> + eeprom@50 {
> + compatible = "atmel,24c08";
> + reg = <0x50>;
> + };
> +
> + eeprom@51 {
> + compatible = "atmel,24c08";
> + reg = <0x51>;
> + };
> +};
> +
> +&sgpiom0 {
> + status = "okay";
> + ngpios = <128>;
> +};
> +
> +&video {
> + status = "okay";
> + memory-region = <&video_engine_memory>;
> +};
> +
> +&sdc {
> + status = "okay";
> +};
> +
> +&lpc_snoop {
> + status = "okay";
> + snoop-ports = <0x80>;
> +};
> +
> +&kcs1 {
> + aspeed,lpc-io-reg = <0xca0>;
> + status = "okay";
> +};
> +
> +&kcs2 {
> + aspeed,lpc-io-reg = <0xca8>;
> + status = "okay";
> +};
> +
> +&kcs3 {
> + aspeed,lpc-io-reg = <0xca2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> + /* GPIOB6 will be used in ASD function, do not set to be TXD4 */
> + pinctrl-0 = <&pinctrl_txd2_default &pinctrl_rxd2_default>;
Are you sure this works? You're configuring the pins for UART2 on the
node for UART4. Enable UART2 instead?
Andrew
