Re: [PATCH 02/10] dt-bindings: PCI: qcom: Do not require 'msi-map-mask'

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Feb 21, 2024 at 11:30:58AM +0100, Johan Hovold wrote:
> On Wed, Feb 21, 2024 at 10:56:07AM +0530, Manivannan Sadhasivam wrote:
> > On Tue, Feb 20, 2024 at 08:41:25AM +0100, Johan Hovold wrote:
> > > On Fri, Feb 16, 2024 at 10:24:06PM +0530, Manivannan Sadhasivam wrote:
> 
> > > > msi-map-mask is definitely needed as it would allow all the devices under the
> > > > same bus to reuse the MSI identifier. Currently, excluding this property will
> > > > not cause any issue since there is a single device under each bus. But we cannot
> > > > assume that is going to be the case on all boards.
> > > 
> > > Are you saying that there is never a use case for an identity mapping?
> > > Just on Qualcomm hardware or in general?
> > > 
> > > It looks like we have a fairly large number of mainline devicetrees that
> > > do use an identity mapping here (i.e. do not specify 'msi-map-mask') and
> > > the binding document also has an explicit example of this.
> > > 
> > > 	Documentation/devicetree/bindings/pci/pci-msi.txt
> > 
> > I don't know how other platforms supposed to work without this property for more
> > than one devices. Maybe they were not tested enough?
> 
> Seems a bit far fetched since it's also an example in the binding.
> 
> In fact, only the two Qualcomm platforms that you added 'msi-map-mask'
> for use it.
> 
> > But for sure, Qcom SoCs require either per device MSI identifier or
> > msi-map-mask.
> 
> But isn't the mapping set up by the boot firmware and can differ between
> platforms?
> 
> The mapping on sc8280xp looks quite different from sm8450/sm8650:
> 
> 	msi-map = <0x0 &gic_its 0x5981 0x1>,
> 		  <0x100 &gic_its 0x5980 0x1>;
> 	msi-map-mask = <0xff00>;
> 
> Here it's obvious that the mask is needed, whereas for sc8280xp:
> 
> 	msi-map = <0x0 &its 0xa0000 0x10000>;
> 
> it's not obvious what the mask should be. In fact, it looks like
> Qualcomm intended a linear mapping here as the length is 0x10000 and
> they left out the mask.
> 
> And after digging through the X13s ACPI tables, this is indeed how the
> hardware is configured, which means that we should not use a
> 'msi-map-mask' property for sc8280xp and that this patch is correct.
> 

Right. Confirmed the same with the hw team. On Qcom SoCs ITS mapping is
relatively similar to SMMU stream IDs. So on SM8450 and other mobile targets
making use of SMMUv2, only 128 SIDs are available, hence only 128 MSI
identifiers. But on SC8280XP and other similar ones, SMMUv3 is used, so there
are 65536 SIDs available and also the MSI identifiers. So yes, this SoC indeed
supports linear mapping of MSI identifiers and so the mask is not required.

Thanks!

- Mani

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux