The devices in the wkup domain are capable of waking up the system from suspend. We can configure the wkup domain devices in a generic way using the ti-sysc interconnect target module driver like we have done with the earlier TI SoCs. As ti-sysc manages the SYSCONFIG related registers independent of the child hardware device, the wake-up configuration is also set even if wkup_uart0 is reserved by sysfw. The wkup_uart0 device has interconnect target module register mapping like dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP block in the target module. The power domain and clock affects the whole interconnect target module. Note we change the functional clock name to follow the ti-sysc binding and use "fck" instead of "fclk". Also note that we need to disable the target module reset as noted by Markus. Otherwise the sysfw using wkup_uart0 can get confused on some devices leading to boot time issues such as mbox timeouts. Tested-by: Dhruva Gole <d-gole@xxxxxx> Reviewed-by: Kevin Hilman <khilman@xxxxxxxxxxxx> Tested-by: Markus Schneider-Pargmann <msp@xxxxxxxxxxxx> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx> --- Changes since v4: - Add ti,no-reset-on-init as noted by Markus Changes since v3: - Use the first reg for the target module node name to avoid a make W=1 dtbs warning as noted by Nishanth Changes since v2: - Fix node name for 8250 IP, it's at offset 0 from the target module - Added Kevin's Reviewed-by from v2 as the node name change is mostly cosmetic Changes since v1: - Added Tested-by from Dhruva --- arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi | 34 ++++++++++++++++++---- 1 file changed, 28 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi --- a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi @@ -5,6 +5,8 @@ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/ */ +#include <dt-bindings/bus/ti-sysc.h> + &cbass_wakeup { wkup_conf: syscon@43000000 { bootph-all; @@ -21,14 +23,34 @@ chipid: chipid@14 { }; }; - wkup_uart0: serial@2b300000 { - compatible = "ti,am64-uart", "ti,am654-uart"; - reg = <0x00 0x2b300000 0x00 0x100>; - interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; + target-module@2b300050 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0 0x2b300050 0 0x4>, + <0 0x2b300054 0 0x4>, + <0 0x2b300058 0 0x4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP | + SYSC_OMAP2_SOFTRESET | + SYSC_OMAP2_AUTOIDLE)>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + ti,syss-mask = <1>; + ti,no-reset-on-init; power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 114 0>; - clock-names = "fclk"; - status = "disabled"; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x2b300000 0x100000>; + + wkup_uart0: serial@0 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0 0x100>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; }; wkup_i2c0: i2c@2b200000 { -- 2.43.1