The formally correct node names have "ethernet-*" prefix on
switch, ports, port and phy, fix it up.
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts | 26 +++++++++++------------
1 file changed, 13 insertions(+), 13 deletions(-)
diff --git a/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
index 396149664297..30c931415680 100644
--- a/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
@@ -187,7 +187,7 @@ touchkeys@26 {
};
/* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */
- switch {
+ ethernet-switch {
compatible = "realtek,rtl8366rb";
/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
@@ -204,36 +204,36 @@ switch_intc: interrupt-controller {
#interrupt-cells = <1>;
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "lan0";
phy-handle = <&phy0>;
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan1";
phy-handle = <&phy1>;
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan2";
phy-handle = <&phy2>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan3";
phy-handle = <&phy3>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "wan";
phy-handle = <&phy4>;
};
- rtl8366rb_cpu_port: port@5 {
+ rtl8366rb_cpu_port: ethernet-port@5 {
reg = <5>;
label = "cpu";
ethernet = <&gmac0>;
@@ -252,27 +252,27 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- phy0: phy@0 {
+ phy0: ethernet-phy@0 {
reg = <0>;
interrupt-parent = <&switch_intc>;
interrupts = <0>;
};
- phy1: phy@1 {
+ phy1: ethernet-phy@1 {
reg = <1>;
interrupt-parent = <&switch_intc>;
interrupts = <1>;
};
- phy2: phy@2 {
+ phy2: ethernet-phy@2 {
reg = <2>;
interrupt-parent = <&switch_intc>;
interrupts = <2>;
};
- phy3: phy@3 {
+ phy3: ethernet-phy@3 {
reg = <3>;
interrupt-parent = <&switch_intc>;
interrupts = <3>;
};
- phy4: phy@4 {
+ phy4: ethernet-phy@4 {
reg = <4>;
interrupt-parent = <&switch_intc>;
interrupts = <12>;
--
2.34.1
