Bindings say DMA channels are in order Rx, Tx. Adjust the DT nodes accordingly. While at it, use defines for the flags. Signed-off-by: Alexander Stein <alexander.stein@xxxxxxxxxxxxxxx> --- Changes in v2: * Use defines from dt-bindings/dma/fsl-edma.h * Switch DMA channel flags as well arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi index a180893ac81e0..cab3468b1875e 100644 --- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi @@ -5,6 +5,7 @@ */ #include <dt-bindings/clock/imx8-lpcg.h> +#include <dt-bindings/dma/fsl-edma.h> #include <dt-bindings/firmware/imx/rsrc.h> dma_ipg_clk: clock-dma-ipg { @@ -93,8 +94,8 @@ lpuart0: serial@5a060000 { assigned-clocks = <&clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <80000000>; power-domains = <&pd IMX_SC_R_UART_0>; - dma-names = "tx","rx"; - dmas = <&edma2 9 0 0>, <&edma2 8 0 1>; + dma-names = "rx", "tx"; + dmas = <&edma2 8 0 FSL_EDMA_RX>, <&edma2 9 0 0>; status = "disabled"; }; @@ -107,8 +108,8 @@ lpuart1: serial@5a070000 { assigned-clocks = <&clk IMX_SC_R_UART_1 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <80000000>; power-domains = <&pd IMX_SC_R_UART_1>; - dma-names = "tx","rx"; - dmas = <&edma2 11 0 0>, <&edma2 10 0 1>; + dma-names = "rx", "tx"; + dmas = <&edma2 10 0 FSL_EDMA_RX>, <&edma2 11 0 0>; status = "disabled"; }; @@ -121,8 +122,8 @@ lpuart2: serial@5a080000 { assigned-clocks = <&clk IMX_SC_R_UART_2 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <80000000>; power-domains = <&pd IMX_SC_R_UART_2>; - dma-names = "tx","rx"; - dmas = <&edma2 13 0 0>, <&edma2 12 0 1>; + dma-names = "rx", "tx"; + dmas = <&edma2 12 0 FSL_EDMA_RX>, <&edma2 13 0 0>; status = "disabled"; }; @@ -135,8 +136,8 @@ lpuart3: serial@5a090000 { assigned-clocks = <&clk IMX_SC_R_UART_3 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <80000000>; power-domains = <&pd IMX_SC_R_UART_3>; - dma-names = "tx","rx"; - dmas = <&edma2 15 0 0>, <&edma2 14 0 1>; + dma-names = "rx", "tx"; + dmas = <&edma2 14 0 FSL_EDMA_RX>, <&edma2 15 0 0>; status = "disabled"; }; -- 2.34.1