Re: [PATCH 3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support

Andre Przywara <andre.przywara@xxxxxxx> · Tue, 6 Feb 2024 00:47:05 +0000

Hi Jernej,

thanks for having a look!

On 05/02/2024 19:20, Jernej Škrabec wrote:
Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
Hi Andre!

Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
	- 1 or 2 GB DRAM
	- 8 or 16 GB eMMC flash
	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
	- RTL8723BS WiFi & Bluetooth chip
	- HDMI port
	- two USB 2.0 ports
	- 3.5mm AV port
	- microSD card slot

The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.

Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
---
  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
  .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
  2 files changed, 358 insertions(+)
  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 91d505b385de..2db3b15ad09f 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
new file mode 100644
index 000000000000..537923a541a8
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2018 ARM Ltd.

Shouldn't be 2024?

Well, that just documents that sad fact that I indeed created this file 
6 years ago, but just managed now to actually send this. Is there a 
requirement for this being "recent"?


+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+#include "sun50i-a64-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Remix Mini PC";
+	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
+		     "allwinner,sun50i-a64";
+
+	aliases {
+		ethernet1 = &rtl8723bs;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	reg_vcc5v: regulator-5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	cpvdd-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+/* Connects to the AC200 chip */
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&i2c0_pins {
+	bias-pull-up;
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_aldo1>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723bs: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};

Node without compatible doesn't help. Please remove it.

Huh, but where do I put the the IRQ line then? And every other RTL8723BS 
user seems to do the same?


+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_eldo1>;
+	bus-width = <8>;
+	non-removable;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;

Aren't these speed modes enabled by default?

Enabled by who? Our current sunxi-mmc driver? I cannot find anything in 
the binding that suggests that there would be some default settings.

Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
removed.

Mmh, I am confused: I thought after the H5 eMMC mishap we figured that 
all speed modes supported by the eMMC chip should be listed in the DT?
So any driver wouldn't need to make assumptions, and if a particular 
mode shows problems on a board, we just remove that mode from the DT.
Actually, thinking about that, I guess I should list HS-400 as well? The 
BSP kernel uses that mode.
Or do you mean to say that in particular DDR (@1.8V) is problematic? I 
cannot test at the moment, but could try later to force that mode.

Cheers,
Andre


+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_dcdc1>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pe-supply = <&reg_dcdc1>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_dldo4>;
+	vcc-ph-supply = <&reg_dcdc1>;
+};
+
+&r_ir {
+	status = "okay";
+};
+
+&r_pio {
+	/*
+	 * We cannot add that supply for now since it would create a circular
+	 * dependency between pinctrl, the regulator and the RSB Bus.
+	 *
+	 * vcc-pl-supply = <&reg_aldo2>;
+	 */
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+		vin5-supply = <&reg_vcc5v>;
+		vin6-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		dldoin-supply = <&reg_vcc5v>;
+		eldoin-supply = <&reg_vcc5v>;
+		fldoin-supply = <&reg_vcc5v>;
+		drivevbus-supply = <&reg_vcc5v>;
+		ips-supply = <&reg_vcc5v>;
+
+		status = "okay";
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+/* Deviates from the reset default of 1.1V. */
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_aldo2 {
+	/* Specifying R_PIO consumer would create circular dependency. */
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+/* AC200 power supply */
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-ave-33";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-cpvdd-dram-emmc";
+};
+
+/* Supplies the arisc management core, needed by TF-A to power off cores. */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dcdc1>;
+};
+
+&sound {
+	simple-audio-card,aux-devs = <&codec_analog>;
+	simple-audio-card,widgets = "Microphone", "Microphone Jack",
+				    "Headphone", "Headphone Jack";
+	simple-audio-card,routing =
+			"Left DAC", "DACL",
+			"Right DAC", "DACR",
+			"Headphone Jack", "HP",
+			"ADCL", "Left ADC",
+			"ADCR", "Right ADC",
+			"MIC2", "Microphone Jack";
+	status = "okay";
+};
+
+/* On the (unpopulated) UART pads. */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+		max-speed = <1500000>;
+	};
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_drivevbus>;
+	status = "okay";
+};

















