AM62P supports image capture via the MIPI CSI-2 protocol, it uses three
IPs to achieve this: Cadence DPHY, Cadence CSI-RX, and TI's pixelgrabber
wrapper on top. Enable all of these IPs in the devicetree.
Signed-off-by: Jai Luthra <j-luthra@xxxxxx>
---
arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 61 +++++++++++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
index 57ec4ef334e4..fdd835a04327 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
@@ -928,4 +928,65 @@ mcasp2: audio-controller@2b20000 {
power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
status = "disabled";
};
+
+ ti_csi2rx0: ticsi2rx@30102000 {
+ compatible = "ti,j721e-csi2rx-shim";
+ reg = <0x00 0x30102000 0x00 0x1000>;
+ ranges;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ dmas = <&main_bcdma_csi 0 0x5000 0>;
+ dma-names = "rx0";
+ power-domains = <&k3_pds 182 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+
+ cdns_csi2rx0: csi-bridge@30101000 {
+ compatible = "ti,j721e-csi2rx", "cdns,csi2rx";
+ reg = <0x00 0x30101000 0x00 0x1000>;
+ clocks = <&k3_clks 182 0>, <&k3_clks 182 3>, <&k3_clks 182 0>,
+ <&k3_clks 182 0>, <&k3_clks 182 4>, <&k3_clks 182 4>;
+ clock-names = "sys_clk", "p_clk", "pixel_if0_clk",
+ "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk";
+ phys = <&dphy0>;
+ phy-names = "dphy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "disabled";
+ };
+
+ csi0_port1: port@1 {
+ reg = <1>;
+ status = "disabled";
+ };
+
+ csi0_port2: port@2 {
+ reg = <2>;
+ status = "disabled";
+ };
+
+ csi0_port3: port@3 {
+ reg = <3>;
+ status = "disabled";
+ };
+
+ csi0_port4: port@4 {
+ reg = <4>;
+ status = "disabled";
+ };
+ };
+ };
+ };
+
+ dphy0: phy@30110000 {
+ compatible = "cdns,dphy-rx";
+ reg = <0x00 0x30110000 0x00 0x1100>;
+ #phy-cells = <0>;
+ power-domains = <&k3_pds 185 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
};
--
2.43.0
