Re: [PATCH 2/3] dt-bindings: fpga: xlnx,fpga-slave-selectmap: add DT schema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 29/01/2024 23:56, Charles Perry wrote:
> Document the slave SelectMAP interface of Xilinx 7 series FPGA.
> 
> Signed-off-by: Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx>
> ---
>  .../fpga/xlnx,fpga-slave-selectmap.yaml       | 85 +++++++++++++++++++
>  1 file changed, 85 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-selectmap.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-selectmap.yaml b/Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-selectmap.yaml
> new file mode 100644
> index 0000000000000..20cea24e3e39a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-selectmap.yaml
> @@ -0,0 +1,85 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fpga/xlnx,fpga-slave-selectmap.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Xilinx Slave SelectMAP FPGA
> +
> +description: |
> +  Xilinx 7 Series FPGAs support a method of loading the bitstream over a
> +  parallel port named the slave SelectMAP interface in the documentation. Only
> +  the x8 mode is supported where data is loaded at one byte per rising edge of
> +  the clock, with the MSB of each byte presented to the D0 pin.
> +
> +  Datasheets:
> +    https://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - xlnx,fpga-slave-selectmap

You did not test bindings, so only limited review.

> +
> +  reg:
> +    description:
> +      At least 1 byte of memory mapped IO
> +    maxItems: 1
> +
> +  prog_b-gpios:


No underscores in names.


> +    description:
> +      config pin (referred to as PROGRAM_B in the manual)
> +    maxItems: 1
> +
> +  done-gpios:
> +    description:
> +      config status pin (referred to as DONE in the manual)
> +    maxItems: 1
> +
> +  init-b-gpios:

Is there init-a? Open other bindings and look how these are called there.


> +    description:
> +      initialization status and configuration error pin
> +      (referred to as INIT_B in the manual)
> +    maxItems: 1
> +
> +  csi-b-gpios:

Where is csi-a?

> +    description:
> +      chip select pin (referred to as CSI_B in the manual)
> +      Optional gpio for if the bus controller does not provide a chip select.
> +    maxItems: 1
> +
> +  rdwr-b-gpios:
> +    description:
> +      read/write select pin (referred to as RDWR_B in the manual)
> +      Optional gpio for if the bus controller does not provide this pin.
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - prog_b-gpios
> +  - done-gpios
> +  - init-b-gpios
> +
> +additionalProperties: true

Nope, this cannot bue true.

> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    &weim {

Drop or use some generic soc

> +      status = "okay";

Drop

> +      ranges = <0 0 0x08000000 0x04000000>;

Drop

> +
> +      fpga_mgr: fpga_programmer@0,0 {

No underscores in names, drop label.

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +        compatible = "xlnx,fpga-slave-selectmap";
> +        reg = <0 0 0x4000000>;
> +        fsl,weim-cs-timing = <0x00070031 0x00000142
> +              0x00020000 0x00000000
> +              0x0c000645 0x00000000>;

NAK.

Please run your patch through Xilinx folks before sending.

Best regards,
Krzysztof





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux