On Tue, Jan 30, 2024 at 11:41:11AM +0530, Viresh Kumar wrote:
> On 29-01-24, 21:34, Manivannan Sadhasivam wrote:
> > On Fri, Jan 12, 2024 at 07:52:04PM +0530, Krishna chaitanya chundru wrote:
> > > PCIe needs to choose the appropriate performance state of RPMH power
> > > domain and interconnect bandwidth based up on the PCIe gen speed.
> > >
> > > Add the OPP table support to specify RPMH performance states and
> > > interconnect peak bandwidth.
> > >
> > > Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> > > ---
> > > arch/arm64/boot/dts/qcom/sm8450.dtsi | 74 ++++++++++++++++++++++++++++++++++++
> > > 1 file changed, 74 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> > > index 6b1d2e0d9d14..eab85ecaeff0 100644
> > > --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> > > @@ -1827,7 +1827,32 @@ pcie0: pcie@1c00000 {
> > > pinctrl-names = "default";
> > > pinctrl-0 = <&pcie0_default_state>;
> > >
> > > + operating-points-v2 = <&pcie0_opp_table>;
> > > +
> > > status = "disabled";
> > > +
> > > + pcie0_opp_table: opp-table {
> > > + compatible = "operating-points-v2";
> > > +
> > > + opp-2500000 {
> > > + opp-hz = /bits/ 64 <2500000>;
> > > + required-opps = <&rpmhpd_opp_low_svs>;
> > > + opp-peak-kBps = <250000 250000>;
> >
> > This is a question for Viresh: We already have macros in the driver to derive
> > the bandwidth based on link speed. So if OPP core exposes a callback to allow
> > the consumers to set the bw on its own, we can get rid of this entry.
> >
> > Similar to config_clks()/config_regulators(). Is that feasible?
>
> I don't have any issues with a new callback for bw. But, AFAIU, the DT
> is required to represent the hardware irrespective of what any OS
> would do with it. So DT should ideally have these values here, right ?
>
Not necessarily. Because, right now the bandwidth values of the all peripherals
are encoded within the drivers. Only OPP has the requirement to define the
values in DT.
> Also, the driver has already moved away from using those macros now
> and depend on the OPP core to do the right thing. It only uses the
> macro for the cases where the DT OPP table isn't available. And as
> said by few others as well already, the driver really should try to
> add OPPs dynamically in that case to avoid multiple code paths and
> stick to a single OPP based solution.
>
Still I prefer to use OPP for bandwidth control because both the voltage and
bandwidth values need to be updated at the same time. My only point here is, if
OPP exposes a callback for bw, then we can keep the DT behavior consistent.
- Mani
> --
> viresh
--
மணிவண்ணன் சதாசிவம்
