On Sun, 28 Jan 2024 00:32:46 +0800
Chen-Yu Tsai <wens@xxxxxxxxxx> wrote:
> From: Chen-Yu Tsai <wens@xxxxxxxx>
>
> The DMA controllers found on the H616 and H618 are the same as the one
> found on the A100. The only difference is the DMA endpoint (DRQ) layout.
>
> Add a device node for it, and add DMA channels for existing peripherals.
Thanks for the changes! I compared all bits against the manual: they match.
> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
Reviewed-by: Andre Przywara <andre.przywara@xxxxxxx>
Cheers,
Andre
> ---
> Changes since v1:
> - Fall back to A100 instead of H6
> - Add DMA channels for r_i2c
>
> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 41 +++++++++++++++++++
> 1 file changed, 41 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> index d549d277d972..885809137b9d 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> @@ -133,6 +133,19 @@ ccu: clock@3001000 {
> #reset-cells = <1>;
> };
>
> + dma: dma-controller@3002000 {
> + compatible = "allwinner,sun50i-h616-dma",
> + "allwinner,sun50i-a100-dma";
> + reg = <0x03002000 0x1000>;
> + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
> + clock-names = "bus", "mbus";
> + dma-channels = <16>;
> + dma-requests = <49>;
> + resets = <&ccu RST_BUS_DMA>;
> + #dma-cells = <1>;
> + };
> +
> sid: efuse@3006000 {
> compatible = "allwinner,sun50i-h616-sid", "allwinner,sun50i-a64-sid";
> reg = <0x03006000 0x1000>;
> @@ -339,6 +352,8 @@ uart0: serial@5000000 {
> reg-shift = <2>;
> reg-io-width = <4>;
> clocks = <&ccu CLK_BUS_UART0>;
> + dmas = <&dma 14>, <&dma 14>;
> + dma-names = "tx", "rx";
> resets = <&ccu RST_BUS_UART0>;
> status = "disabled";
> };
> @@ -350,6 +365,8 @@ uart1: serial@5000400 {
> reg-shift = <2>;
> reg-io-width = <4>;
> clocks = <&ccu CLK_BUS_UART1>;
> + dmas = <&dma 15>, <&dma 15>;
> + dma-names = "tx", "rx";
> resets = <&ccu RST_BUS_UART1>;
> status = "disabled";
> };
> @@ -361,6 +378,8 @@ uart2: serial@5000800 {
> reg-shift = <2>;
> reg-io-width = <4>;
> clocks = <&ccu CLK_BUS_UART2>;
> + dmas = <&dma 16>, <&dma 16>;
> + dma-names = "tx", "rx";
> resets = <&ccu RST_BUS_UART2>;
> status = "disabled";
> };
> @@ -372,6 +391,8 @@ uart3: serial@5000c00 {
> reg-shift = <2>;
> reg-io-width = <4>;
> clocks = <&ccu CLK_BUS_UART3>;
> + dmas = <&dma 17>, <&dma 17>;
> + dma-names = "tx", "rx";
> resets = <&ccu RST_BUS_UART3>;
> status = "disabled";
> };
> @@ -383,6 +404,8 @@ uart4: serial@5001000 {
> reg-shift = <2>;
> reg-io-width = <4>;
> clocks = <&ccu CLK_BUS_UART4>;
> + dmas = <&dma 18>, <&dma 18>;
> + dma-names = "tx", "rx";
> resets = <&ccu RST_BUS_UART4>;
> status = "disabled";
> };
> @@ -394,6 +417,8 @@ uart5: serial@5001400 {
> reg-shift = <2>;
> reg-io-width = <4>;
> clocks = <&ccu CLK_BUS_UART5>;
> + dmas = <&dma 19>, <&dma 19>;
> + dma-names = "tx", "rx";
> resets = <&ccu RST_BUS_UART5>;
> status = "disabled";
> };
> @@ -405,6 +430,8 @@ i2c0: i2c@5002000 {
> reg = <0x05002000 0x400>;
> interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C0>;
> + dmas = <&dma 43>, <&dma 43>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_I2C0>;
> pinctrl-names = "default";
> pinctrl-0 = <&i2c0_pins>;
> @@ -420,6 +447,8 @@ i2c1: i2c@5002400 {
> reg = <0x05002400 0x400>;
> interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C1>;
> + dmas = <&dma 44>, <&dma 44>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_I2C1>;
> status = "disabled";
> #address-cells = <1>;
> @@ -433,6 +462,8 @@ i2c2: i2c@5002800 {
> reg = <0x05002800 0x400>;
> interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C2>;
> + dmas = <&dma 45>, <&dma 45>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_I2C2>;
> status = "disabled";
> #address-cells = <1>;
> @@ -446,6 +477,8 @@ i2c3: i2c@5002c00 {
> reg = <0x05002c00 0x400>;
> interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C3>;
> + dmas = <&dma 46>, <&dma 46>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_I2C3>;
> status = "disabled";
> #address-cells = <1>;
> @@ -459,6 +492,8 @@ i2c4: i2c@5003000 {
> reg = <0x05003000 0x400>;
> interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C4>;
> + dmas = <&dma 47>, <&dma 47>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_I2C4>;
> status = "disabled";
> #address-cells = <1>;
> @@ -472,6 +507,8 @@ spi0: spi@5010000 {
> interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> clock-names = "ahb", "mod";
> + dmas = <&dma 22>, <&dma 22>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_SPI0>;
> status = "disabled";
> #address-cells = <1>;
> @@ -485,6 +522,8 @@ spi1: spi@5011000 {
> interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> clock-names = "ahb", "mod";
> + dmas = <&dma 23>, <&dma 23>;
> + dma-names = "rx", "tx";
> resets = <&ccu RST_BUS_SPI1>;
> status = "disabled";
> #address-cells = <1>;
> @@ -734,6 +773,8 @@ r_i2c: i2c@7081400 {
> reg = <0x07081400 0x400>;
> interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&r_ccu CLK_R_APB2_I2C>;
> + dmas = <&dma 48>, <&dma 48>;
> + dma-names = "rx", "tx";
> resets = <&r_ccu RST_R_APB2_I2C>;
> status = "disabled";
> #address-cells = <1>;
