On Thu, Jan 25, 2024 at 01:57:20PM +0800, Jie Luo wrote: > > > On 1/25/2024 5:36 AM, Christian Marangi wrote: > > This was a long journey to arrive and discover this problem. > > > > To not waste too much char, there is a race problem with PHY and driver > > probe. This was observed with Aquantia PHY firmware loading. > > > > With some hacks the race problem was workarounded but an interesting > > thing was notice. It took more than a minute for the firmware to load > > via MDIO. > > > > This was strange as the same operation was done by UBoot in at max 5 > > second and the same data was loaded. > > > > A similar problem was observed on a mtk board that also had an > > Aquantia PHY where the load was very slow. It was notice that the cause > > was the MDIO bus running at a very low speed and the firmware > > was missing a property (present in mtk sdk) that set the right frequency > > to the MDIO bus. > > > > It was fun to find that THE VERY SAME PROBLEM is present on IPQ in a > > different form. The MDIO apply internally a division to the feed clock > > resulting in the bus running at 390KHz instead of 6.25Mhz. > > > > Searching around the web for some documentation and some include and > > analyzing the uboot codeflow resulted in the divider being set wrongly > > at /256 instead of /16 as the value was actually never set. > > Applying the value restore the original load time for the Aquantia PHY. > > > > This series mainly handle this by adding support for the "clock-frequency" > > property. > > > > Christian Marangi (3): > > dt-bindings: net: ipq4019-mdio: document now supported clock-frequency > > net: mdio: ipq4019: add support for clock-frequency property > > arm64: dts: qcom: ipq8074: add clock-frequency to MDIO node > > > > .../bindings/net/qcom,ipq4019-mdio.yaml | 10 +++ > > arch/arm64/boot/dts/qcom/ipq8074.dtsi | 2 + > > drivers/net/mdio/mdio-ipq4019.c | 68 +++++++++++++++++-- > > 3 files changed, 75 insertions(+), 5 deletions(-) > > > > Hi Christian, > Just a gentle reminder. > Hi Jie, hope you can understand my reason. > The MDIO frequency config is already added by the following patch series. > https://lore.kernel.org/netdev/28c8b31c-8dcb-4a19-9084-22c77a74b9a1@xxxxxxxxxx/T/#m840cb8d269dca133c3ad3da3d112c63382ec2058 > Wasn't aware of this, as I said in the cover letter this all comes by a problem we notice in the Aquantia firmware load that was slow as hell and we just notice the misconfiguration of the divisor. The feature in this series is really a simple one and almost ready (I already have v2 ready for the request from Andrew to follow 802.3 spec) and we really need it ASAP as we are trying to move our ipq807x targets to upstream driver and finally start using the integrated firmware loading for Aquantia PHY. Also I can see some fundamental difference between the 2 patch, mainly in how the value is applied and setting a sane divisor by default instead of using 0xff. (probably Andrew would have pointed out the same thing in some later revision to your series) Looking at the linked series I notice there are still some thing to polish and to clarify with DT and driver and I think it's only beneficial if this feature is worked separately as it's not only needed for ipq50xx but affects every user of this (ipq40xx, ipq807x, ipq60xx) and it would be a pitty to wait the entire ipq50xx series to be handled just to fix a long lasting misconfiguration on various SoC family. Hope you can understand these reasons, it's all for the sake of making this driver more mature quicker. > This MDIO patch series will be updated to just keep the MDIO frequency > patch and DT document for this MDIO frequency property added. > > For CMN PLL config will be moved to the CMN PLL clock driver and the UNIPHY > clock config will be moved the uniphy driver as suggested by > Sergey's suggestions. > > Thanks. > > -- Ansuel
