Enable the UFS found on the SM7125 Xiaomi smartphones. Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx> Signed-off-by: David Wronek <davidwronek@xxxxxxxxx> --- arch/arm64/boot/dts/qcom/sm7125-xiaomi-common.dtsi | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm7125-xiaomi-common.dtsi b/arch/arm64/boot/dts/qcom/sm7125-xiaomi-common.dtsi index e55cd83c19b8..0dfd1e3730e9 100644 --- a/arch/arm64/boot/dts/qcom/sm7125-xiaomi-common.dtsi +++ b/arch/arm64/boot/dts/qcom/sm7125-xiaomi-common.dtsi @@ -152,6 +152,9 @@ vreg_l4a_0p88: ldo4 { regulator-min-microvolt = <824000>; regulator-max-microvolt = <928000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l5a_2p7: ldo5 { @@ -188,6 +191,9 @@ vreg_l12a_1p8: ldo12 { regulator-min-microvolt = <1696000>; regulator-max-microvolt = <1952000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l13a_1p8: ldo13 { @@ -230,6 +236,9 @@ vreg_l19a_3p0: ldo19 { regulator-min-microvolt = <2696000>; regulator-max-microvolt = <3304000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; }; @@ -258,6 +267,9 @@ vreg_l3c_1p23: ldo3 { regulator-min-microvolt = <1144000>; regulator-max-microvolt = <1304000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l4c_1p8: ldo4 { @@ -398,6 +410,22 @@ sd-cd-pins { }; }; +&ufs_mem_hc { + vcc-supply = <&vreg_l19a_3p0>; + vcc-max-microamp = <600000>; + vccq2-supply = <&vreg_l12a_1p8>; + vccq2-max-microamp = <600000>; + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l4a_0p88>; + vdda-pll-supply = <&vreg_l3c_1p23>; + vdda-phy-max-microamp = <62900>; + vdda-pll-max-microamp = <18300>; + status = "okay"; +}; + &usb_1 { qcom,select-utmi-as-pipe-clk; status = "okay"; -- 2.43.0